Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P050031  Vehicle Speed Sensor "A" No Signal  


DESCRIPTION

Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU (brake actuator assembly) and speed sensor. The speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the certification ECU (smart key ECU assembly) and combination meter assembly. The ECM determines the vehicle speed based on the frequency of the pulse signal.

HINT:
·

Various systems use the vehicle speed signal distributed from the combination meter assembly. Check all the components possibly related to the speed signal.

·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly.

The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems using the speed signal will not operate normally.



A429588E01
4.24,1.958 5.469,2.729 1.229,0.771 10 false Combination Meter Assembly 6.375,1.979 6.833,2.177 0.458,0.198 10 false ECM 5.521,0.969 6.594,1.167 1.073,0.198 10 false 4-Pulse 3.76,0.938 4.833,1.135 1.073,0.198 10 false 4-Pulse 2.188,0.948 3.26,1.146 1.073,0.198 10 false 4-Pulse 1.063,1.99 3.51,2.188 2.448,0.198 10 false Skid Control ECU 0.115,1.313 0.885,1.854 0.771,0.542 10 false from Speed Sensor 2.479,1.99 4.052,2.792 1.573,0.802 10 false Certification ECU (Smart Key ECU Assembly)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P050031 Vehicle Speed Sensor "A" No Signal While vehicle being driven, no vehicle speed sensor signal transmitted to ECM (2 trip detection logic).
·

Open or short in speed signal circuit

·

Combination meter assembly

·

ECM


Comes on SAE: P0500

MONITOR DESCRIPTION

If there is no speed signal from the combination meter assembly even though the ECM determines that the vehicle is being driven, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores this DTC.

CONFIRMATION DRIVING PATTERN

A198825E25
1.281,0.875 1.833,1.104 0.552,0.229 10 24 km/h 1.427,2.031 1.927,2.24 0.5,0.208 10 Idling 0.625,2.375 1.823,2.552 1.198,0.177 10 Ignition Switch ON 2.406,2.229 2.635,2.396 0.229,0.167 10 [A] 4.708,0.417 4.917,0.583 0.208,0.167 10 [B] 6.229,3.229 6.427,3.427 0.198,0.198 10 [C] 3.729,2.99 5.646,3.135 1.917,0.146 10 Total of 30 seconds or more

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine.

7.

Drive the vehicle at 24 km/h (15 mph) or more for a total of 30 seconds or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P050031.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A342543E13
0.073,1.667 2.208,2.115 2.135,0.448 10 false from Certification ECU (Smart Key ECU Assembly) 2.219,2.406 4.094,2.76 1.875,0.354 10 false Combination Meter Assembly 5.563,2.448 6.125,2.677 0.563,0.229 10 false ECM 4.615,2.792 5.708,3.073 1.094,0.281 10 false to Other ECUs 2.219,2.271 4.188,2.49 1.969,0.219 10 false I6 2.281,1.375 2.875,1.698 0.594,0.323 10 false SI 2.042,1.375 2.635,1.698 0.594,0.323 10 false 18 3.573,1.375 4.167,1.698 0.594,0.323 10 false +S 3.813,1.375 4.406,1.698 0.594,0.323 10 false 35 5.094,1.333 5.688,1.656 0.594,0.323 10 false SPD 4.896,1.375 5.49,1.698 0.594,0.323 10 false 44 5.563,2.281 6.156,2.604 0.594,0.323 10 false B2

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED)
a.

Turn the ignition switch to ON.


b.

Drive the vehicle.


c.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Vehicle Speed
50003 372 212
Result:
Result Proceed to
Values displayed on GTS and speedometer display not equal A
Values displayed on GTS and speedometer display equal B




A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.



Result:
Proceed to
OK
NG



OK

3.CHECK COMBINATION METER SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK COMBINATION METER SYSTEM
a.

Check the circuits that send vehicle speed signals to this system in the combination meter system.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit


Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Start the engine.


e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
HINT:

If no DTCs (no pending DTCs) are output to the GTS, the repair has been successfully completed.


Result:
Proceed to
NEXT




NEXT

END