The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the certification ECU (smart key ECU assembly) which uses this information to create the vehicle speed signal*a. The vehicle speed signal consists of pulses sent to the combination meter assembly from the certification ECU (smart key ECU assembly). To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter assembly. This voltage is sent to the No. 2 skid control ECU. The pulse signal is created by switching the transistor in the certification ECU (smart key ECU assembly) on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the certification ECU (smart key ECU assembly). When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on this pulse signal.
*a: This vehicle speed signal is created by the certification ECU (smart key ECU assembly). There is no actual component that is referred to as the vehicle speed sensor. In addition, for some systems, vehicle speed information may be received via CAN communication.
This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
When the combination meter assembly is replaced, update the ECU security key.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>UPDATE ECU SECURITY KEY
Check if entry and start system DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector (to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I6)Location & Routingewd_type=routing;type=c;code=I6 |
||
| I6-35 (+S) - Body ground | Ignition switch ON | 11 to 14 V |
If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly, the combination meter assembly will output a waveform.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the certification ECU (smart key ECU assembly) connector.
| *a | Front view of wire harness connector (to Certification ECU (Smart Key ECU Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I39)Location & Routingewd_type=routing;type=c;code=I39 |
||
| I39-28 (SPDO) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected (Combination Meter Assembly) |
| *b | Waveform |
Check the input waveform.
Remove the combination meter assembly with the connector(s) still connected.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
Connect an oscilloscope to terminal I6-18 (SI) and body ground.
Turn the ignition switch to ON.
Turn a wheel slowly.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Tester connection | I6-18 (SI) - Body ground |
| Tool setting | 5 V/DIV., 20 ms./DIV. |
| Condition | Ignition switch ON, wheel being rotated |
The waveform is similar to that shown in the illustration.
When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I6 combination meter assembly connector.
Disconnect the I39 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I6,I39)Location & Routingewd_type=routing;type=c,c;code=I6,I39 |
||
| I6-18 (SI) - I39-28 (SPDO) | Always | Below 1 Ω |
| I6-18 (SI) or I39-28 (SPDO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for Radio and Display Type
*2: w/ Navigation System
*3: for 12.3 Inch Display
*4: for Radio Receiver Type, with Multi-display
*5: for V35A-FTS
*6: for 1GR-FE
| *a | Front view of wire harness connector (to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the I11 radio and display receiver assembly connector.*1
Disconnect the I10 radio receiver assembly connector.*4
Disconnect the I21 navigation ECU connector.*2
Disconnect the S22 stereo component amplifier assembly connector.*3
Disconnect the B1*5, B2*6 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I6,I10,I11,I21,S22,B1,B2)Location & Routingewd_type=routing;type=c,c,c,c,c,c,c;code=I6,I10,I11,I21,S22,B1,B2 Click Connector(S22)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Amplifier Assemblyewd_type=component;type=c;code=S22;pinno=11 |
||
| I6-35 (+S) - I10-27 (SPD)*2 | Always | Below 1 Ω |
| I6-35 (+S) - I11-27 (SPD)*1 | Always | Below 1 Ω |
| I6-35 (+S) - I21-9 (SPD)*2 | Always | Below 1 Ω |
| I6-35 (+S) - S22-11 (SPD)*3 | Always | Below 1 Ω |
| I6-35 (+S) - B1-33 (SPD) | Always | Below 1 Ω |
| I6-35 (+S) or I10-27 (SPD)*2 or I11-27 (SPD)*1 or I21-9 (SPD)*2 or S22-11 (SPD)*3 or B1-33*5 or B2-44*6 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check vehicle condition.
| Result | Proceed to |
|---|---|
| w/ Navigation System | A |
| w/o Navigation System | B |
A
B
| *a | Front view of wire harness connector (to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the I21 navigation ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I6)Location & Routingewd_type=routing;type=c;code=I6 |
||
| I6-35 (+S) - Body ground | Ignition switch ON | 11 to 14 V |
If the result is as specified, there may be a short circuit in the navigation ECU.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check vehicle condition.
| Result | Proceed to |
|---|---|
| for Radio Receiver Type, with Multi-display | A |
| except Radio Receiver Type, with Multi-display | B |
A
B
| *a | Front view of wire harness connector (to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the I10 radio receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I6)Location & Routingewd_type=routing;type=c;code=I6 |
||
| I6-35 (+S) - Body ground | Ignition switch ON | 11 to 14 V |
If the result is as specified, there may be a short circuit in the radio receiver assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio Receiver Type)>REMOVAL
NG
Check vehicle condition.
| Result | Proceed to |
|---|---|
| for Radio and Display Type | A |
| except Radio and Display Type | B |
A
B
| *a | Front view of wire harness connector (to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the I11 radio and display receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I6)Location & Routingewd_type=routing;type=c;code=I6 |
||
| I6-35 (+S) - Body ground | Ignition switch ON | 11 to 14 V |
If the result is as specified, there may be a short circuit in the radio receiver assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
NG
Check vehicle condition.
| Result | Proceed to |
|---|---|
| for 12.3 Inch Display | A |
| except 12.3 Inch Display | B |
A
B
| *a | Front view of wire harness connector (to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the S22 stereo component amplifier assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I6)Location & Routingewd_type=routing;type=c;code=I6 |
||
| I6-35 (+S) - Body ground | Ignition switch ON | 11 to 14 V |
If the result is as specified, there may be a short circuit in the stereo component amplifier assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector (to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the B1*1, B2*2 ECM connector.
*1: for V35A-FTS
*2: for 1GR-FE
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I6)Location & Routingewd_type=routing;type=c;code=I6 |
||
| I6-35 (+S) - Body ground | Ignition switch ON | 11 to 14 V |
If the result is as specified, there may be a short circuit in the stereo component amplifier assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>ECM>REMOVAL