Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P160300  Engine Stall History  P160500  Rough Idling  


DESCRIPTION

P160300

After starting the engine, this DTC is stored when the engine stops without the ignition switch being operated.

Using the GTS, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

It is necessary to check if the vehicle has run out of fuel before performing troubleshooting, as this DTC is also stored when the engine stalls due to running out of fuel.

P160500

This DTC is stored if the engine speed drops below the set speed.

Using the GTS, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

It is necessary to check if the vehicle ran out of fuel before performing troubleshooting, as this DTC is also stored when idling is unstable due to running out of fuel.

DTC No. Detection Item DTC Detection Condition MIL Note
P160300 Engine Stall History After monitoring for startability problems (P160400) finishes and 5 seconds or more have elapsed after starting the engine, with the engine running, the engine stops (the engine speed drops to 200 rpm or less) without the ignition switch being operated for 0.5 seconds or more (1 trip detection logic). Does not come on SAE: P1603
P160500 Rough Idling After 5 seconds or more have elapsed after starting the engine, with the engine running, the engine speed drops to 400 rpm or less (1 trip detection logic). Does not come on SAE: P1605

Trouble Area
Ignition system
·

Spark plug

·

Ignition coil assembly


Fuel system
·

Fuel injector assembly

·

Fuel pump

·

Fuel pump control circuit

·

Fuel line

·

Purge VSV system

·

Fuel quality (existence of foreign matter, degradation)


Intake and exhaust systems
·

Mass air flow meter sub-assembly

·

Intake system

(Air leaks or deposit accumulation)

·

Throttle body with motor assembly

·

Air fuel ratio sensor

·

Heated oxygen sensor

·

Camshaft timing oil control valve assembly

·

Variable Valve Timing system (VVT system)

·

Brake booster assembly


Other control systems
·

ECM

·

Wire harness or connector

·

Knock control sensor

·

Engine coolant temperature sensor


Engine
·

Water inlet with thermostat sub-assembly

·

Engine assembly


High load from another system
·

Air conditioning system

·

Power steering system

·

Electrical load signal system

·

A/T system



CAUTION / NOTICE / HINT

HINT:
·

In contrast to normal malfunction diagnosis for components, circuits and systems, DTCs P160300 and P160500 are used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.

As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.

·

If any other DTCs are output, perform troubleshooting for those DTCs first.

·

Use any information from the customer problem analysis about the condition of the vehicle at the time when the problem occurred (how the engine stopped, conditions when the engine was restarted, etc.) as a reference.

Symptom Suspected Area
Engine vibration occurs and engine stops
·

Abnormal mass air flow meter sub-assembly output due to existence of foreign matter

·

Abnormal air fuel ratio due to malfunction of air fuel ratio sensor or heated oxygen sensor, air leaks in intake system or insufficient fuel supply


Engine stops with no engine vibration Ignition system, injection stoppage, high load from external parts
Engine can be started with accelerator pedal depressed Insufficient air volume
Engine stalls or is difficult to start immediately after engine stalled, regardless of whether engine is cold or warm Deposits in intake system or combustion chamber caught temporarily on intake or exhaust valve

·

Read freeze frame data using the GTS. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

·

When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA

·

When DTC P160300 (Engine Stall History) is stored, DTC P160500 (Rough Idling) is also stored. When confirming freeze frame data, check DTC P160500. The ECM stores DTC P160500 first. Therefore, 5 sets of freeze frame data can be confirmed through DTC P160500, enabling the technician to obtain more information.

·

When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.

·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare this data with the freeze frame data.

·

Inspections take into account the fact that the malfunction may not have recurred and place emphasis on checking the vehicle conditions present at the time when the malfunction occurred.

·

When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT
a.

Turn the ignition switch to ON.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
Only DTC P160300 and/or P160500 is output A
DTCs other than P160300 and/or P160500 are output B


HINT:
·

If any DTCs other than P160300 or P160500 are output, troubleshoot those DTCs first.

·

Using freeze frame data, confirm the conditions the moment the DTC was stored and after the DTC was stored. This information can be useful when troubleshooting.





A

2.READ FREEZE FRAME DATA (A/F (O2) SENSOR VOLTAGE B1S1 (B2S1), SHORT FT B1S1 (B2S1) AND LONG FT B1S1 (B2S1))

B

2.READ FREEZE FRAME DATA (A/F (O2) SENSOR VOLTAGE B1S1 (B2S1), SHORT FT B1S1 (B2S1) AND LONG FT B1S1 (B2S1))
a.

Turn the ignition switch to ON.


b.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA

Result:
Freeze Frame Data Item for DTC P160500 Suspected Area Action Proceed to
A/F (O2) Sensor Voltage B1S1 (B2S1) Short FT B1S1 (B2S1) Long FT B1S1 (B2S1)
3.8 V or higher 15% or higher - Fuel pump Go to ENGINE STALLS (from step 16) NEXT
Less than 2.8 V, or 3.8 V or higher Less than -15%, or 15% or higher Less than -15%, or 15% or higher
·

Mass air flow meter sub-assembly

·

Air fuel ratio sensor

·

Fuel pump


Go to ENGINE STALLS (from step 12)*
2.8 V to 3.8 V -15% to 15% -15% to 15% - Go to ENGINE STALLS


HINT:

*: If the value of A/F (O2) Sensor Voltage B1S1 (B2S1), Short FT B1S1 (B2S1) or Long FT B1S1 (B2S1) is as specified, malfunction of a component listed in the "Suspected Area" column of the table is suspected.




NEXT