Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P212012  Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Battery  P212014  Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Ground or Open  P21201F  Throttle/Pedal Position Sensor/Switch "D" Circuit Intermittent  P212512  Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Battery  P212514  Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Ground or Open  P21251F  Throttle/Pedal Position Sensor/Switch "E" Circuit Intermittent  P21382B  Throttle/Pedal Position Sensor/Switch "D"/"E" Voltage Correlation Signal Cross Coupled  


DESCRIPTION

HINT:

These DTCs relate to the accelerator pedal position sensor.


The accelerator pedal position sensor is built into the accelerator pedal and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type sensor and uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0.5 V and 4.75 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the accelerator pedal position sensor itself.

The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.

A255815E87
4.333,2.031 4.208,1.948 false 4.323,2.198 4.208,2.146 false 4.344,2.24 4.229,2.333 false 4.344,2.396 4.229,2.51 false 4.344,2.917 4.219,2.917 false 4.354,3.125 4.208,3.125 false 0.854,2.875 0.5,3.333 true 1.052,2.26 1.302,1.375 1.302,1.375 1.417,1.375 true 4.333,1.833 3.844,0.938 false 1.021,2.542 0.927,1.844 0.927,1.844 0.844,1.844 true 0.552,3.802 1.708,4.135 1.156,0.333 10 false Accelerator Pedal Position Sensor 1.458,1.302 1.938,1.479 0.479,0.177 10 false Magnet 0.313,1.76 0.844,1.938 0.531,0.177 10 false IC No. 1 0.313,3.344 0.844,3.521 0.531,0.177 10 false IC No. 2 2.063,1.74 2.531,1.917 0.469,0.177 10 false VPA 2.063,2.073 2.552,2.271 0.49,0.198 10 false EPA 2.063,2.385 2.583,2.563 0.521,0.177 10 false VCPA 2.063,2.688 2.573,2.865 0.51,0.177 10 false VPA2 2.063,3 2.563,3.198 0.5,0.198 10 false EPA2 2.063,3.323 2.583,3.5 0.521,0.177 10 false VCP2 2.677,3.76 3,3.938 0.323,0.177 10 false ECM 4.271,1.542 4.427,1.719 0.156,0.177 10 false *1 5.865,1.542 6.021,1.719 0.156,0.177 10 false *2 3.917,1.854 4.208,2.031 0.292,0.177 10 false 4.55 3.844,2.063 4.208,2.24 0.365,0.177 10 false 3.988 3.938,2.281 4.229,2.458 0.292,0.177 10 false 3.75 3.875,2.469 4.24,2.646 0.365,0.177 10 false 3.188 3.969,2.823 4.271,3 0.302,0.177 10 false 1.6 3.979,3.042 4.281,3.219 0.302,0.177 10 false 0.8 4.406,3.344 4.698,3.521 0.292,0.177 10 false 0.29 4.26,3.594 4.417,3.771 0.156,0.177 10 false 0 5.781,3.604 6.688,3.792 0.906,0.188 10 false 12.4 4.677,3.583 5.604,3.823 0.927,0.24 10 false Usable Range 4.51,4.063 6.615,4.292 2.104,0.229 10 false Accelerator Pedal Angle (°) 4.385,4.677 6.667,4.854 2.281,0.177 10 false *1: Accelerator Pedal Fully Released 4.385,5.052 6.771,5.219 2.385,0.167 10 false *2: Accelerator Pedal Fully Depressed 2.156,0.813 3.854,1.167 1.698,0.354 10 false Accelerator Pedal Position Sensor Output Voltage (V) 6.479,2.281 6.927,2.51 0.448,0.229 10 false VPA 6.438,1.823 6.865,2 0.427,0.177 10 false VPA2

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P212012 Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Battery VPA is 4.8 V or higher for 2 seconds or more (1 trip detection logic).
·

Accelerator pedal (with sensor) rod assembly

·

Open in EPA circuit

·

Short in VPA circuit

·

ECM


Comes on SAE: P2123
P212014 Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Ground or Open VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is depressed (1 trip detection logic).
·

Accelerator pedal (with sensor) rod assembly

·

Open in VCPA circuit

·

Open or ground short in VPA circuit

·

ECM


Comes on SAE: P2122
P21201F Throttle/Pedal Position Sensor/Switch "D" Circuit Intermittent VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
·

Accelerator pedal (with sensor) rod assembly

·

Open or short in accelerator pedal position sensor circuit

·

ECM


Comes on SAE: P2120
P212512 Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Battery Both of the following conditions are met for 2 seconds or more (1 trip detection logic):
(a) VPA2 is 4.8 V or higher.
(b) VPA is between 0.4 V and 3.45 V.
·

Accelerator pedal (with sensor) rod assembly

·

Open in EPA2 circuit

·

Short in VPA2 circuit

·

ECM


Comes on SAE: P2128
P212514 Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Ground or Open VPA2 is 1.2 V or less for 0.5 seconds or more when the accelerator pedal is depressed (1 trip detection logic).
·

Accelerator pedal (with sensor) rod assembly

·

Open in VCP2 circuit

·

Open or ground short in VPA2 circuit

·

ECM


Comes on SAE: P2127
P21251F Throttle/Pedal Position Sensor/Switch "E" Circuit Intermittent VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
·

Accelerator pedal (with sensor) rod assembly

·

Open or short in accelerator pedal position sensor circuit

·

ECM


Comes on SAE: P2125
P21382B Throttle/Pedal Position Sensor/Switch "D"/"E" Voltage Correlation Signal Cross Coupled Either of the following conditions continues for 2 seconds or more (1 trip detection logic):
(a) The difference between VPA and VPA2 is 0.02 V or less.
(b) VPA is 0.4 V or less, and VPA2 is 1.2 V or less.
·

Short between VPA and VPA2 circuits

·

Accelerator pedal (with sensor) rod assembly

·

ECM


Comes on SAE: P2138

HINT:

When any of these DTCs are output, check the accelerator pedal position sensor voltage using the GTS. Enter the following menus: Powertrain / Engine / Data List / All Data / Accelerator Position Sensor No.1 Voltage and Accelerator Position Sensor No.2 Voltage.

Trouble Area Accelerator Pedal Fully Released Accelerator Pedal Fully Depressed
Accelerator Position Sensor No.1 Voltage Accelerator Position Sensor No.2 Voltage Accelerator Position Sensor No.1 Voltage Accelerator Position Sensor No.2 Voltage
Open in VCP circuit 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V
Open or ground short in VPA circuit 0 to 0.2 V 1.2 to 2.0 V 0 to 0.2 V 3.4 to 4.75 V
Open or ground short in VPA2 circuit 0.5 to 1.1 V 0 to 0.2 V 2.6 to 4.5 V 0 to 0.2 V
Open in EPA circuit 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V
Normal condition 0.5 to 1.1 V 1.2 to 2.0 V 2.6 to 4.5 V 3.4 to 4.75 V


HINT:

Accelerator pedal positions are expressed as voltages.


MONITOR DESCRIPTION

When either output voltage of VPA or VPA2 deviates from the standard range, or the difference between the output voltages of the 2 sensor circuits is more than the threshold, the ECM determines that there is a malfunction in the accelerator pedal position sensor. The ECM then illuminates the MIL and stores a DTC.

Example:

When the output voltage of VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is fully depressed, DTC P212014 is stored.

CONFIRMATION DRIVING PATTERN

A199317E35
3.635,2.01 2.771,1.302 2.771,1.302 2.927,1.302 false 4.729,2.448 5.115,1.802 5.115,1.802 5.26,1.802 false 2.208,2.448 2.438,2.104 2.438,2.104 2.542,2.104 false 0.125,0.094 1.74,0.271 1.615,0.177 10 Accelerator Pedal State 0.865,0.417 1.583,0.563 0.719,0.146 10 Depressed 0.948,0.875 1.594,1.031 0.646,0.156 10 Released 0.427,2.406 1.635,2.573 1.208,0.167 10 Ignition Switch ON 2.094,2.49 2.292,2.677 0.198,0.188 10 [A] 4.385,3.438 4.646,3.646 0.26,0.208 10 [C] 5.365,1.729 6.01,1.885 0.646,0.156 10 Released 2.875,3.052 3.552,3.229 0.677,0.177 10 5 seconds 3.01,1.229 3.729,1.375 0.719,0.146 10 Depressed 3.865,1.125 4.104,1.333 0.24,0.208 10 [B] 2.594,2.031 3.24,2.188 0.646,0.156 10 Released

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Fully depress and release the accelerator pedal [B].

7.

Check that 5 seconds or more have elapsed since the ignition switch is turned to ON.

8.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P212012, P212014, P21201F, P212512, P212514, P21251F or P21382B.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.




FAIL-SAFE

When DTC P212012, P212014, P21201F, P212512, P212514, P21251F or P21382B is stored, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM limits the engine output. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.

Fail-safe mode continues until a pass condition is detected, and the ignition switch is turned off.

WIRING DIAGRAM

A399961E18
0.094,2.948 0.552,3.146 0.458,0.198 10 false B17 0.094,3.146 3.354,3.521 3.26,0.375 10 false Accelerator Pedal Position Sensor (Accelerator Pedal (with Sensor) Rod Assembly) 1.563,0.635 2.021,0.833 0.458,0.198 10 false VPA 1.99,0.542 2.146,0.74 0.156,0.198 10 false 6 1.583,1.031 2.042,1.229 0.458,0.198 10 false EPA 2,0.938 2.156,1.135 0.156,0.198 10 false 5 1.479,1.458 2.094,1.656 0.615,0.198 10 false VCPA 2,1.365 2.156,1.563 0.156,0.198 10 false 4 1.521,1.896 2.135,2.094 0.615,0.198 10 false VPA2 2.01,1.792 2.167,1.99 0.156,0.198 10 false 3 1.51,2.302 2.125,2.5 0.615,0.198 10 false EPA2 2.01,2.198 2.167,2.396 0.156,0.198 10 false 2 1.49,2.729 2.104,2.927 0.615,0.198 10 false VCP2 2.01,2.594 2.167,2.792 0.156,0.198 10 false 1 5.333,0.521 5.646,0.719 0.313,0.198 10 false 53 5.625,0.51 6.083,0.708 0.458,0.198 10 false VPA 5.333,0.948 5.646,1.146 0.313,0.198 10 false 54 5.615,1.188 6.073,1.385 0.458,0.198 10 false EPA 5.333,1.365 5.646,1.563 0.313,0.198 10 false 55 5.615,1.365 6.229,1.563 0.615,0.198 10 false VCPA 5.323,1.781 5.635,1.979 0.313,0.198 10 false 56 5.615,1.771 6.229,1.969 0.615,0.198 10 false VPA2 5.323,2.219 5.635,2.417 0.313,0.198 10 false 57 5.604,2.438 6.219,2.635 0.615,0.198 10 false EPA2 5.333,2.625 5.646,2.823 0.313,0.198 10 false 58 5.604,2.615 6.219,2.813 0.615,0.198 10 false VCP2 5.979,3.146 6.469,3.458 0.49,0.313 10 false B2 5.979,3.302 6.469,3.615 0.49,0.313 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR VOLTAGE)
A208621C05
0.719,1.75 1,1.969 0.281,0.219 10 *a 2.646,1.74 2.927,1.979 0.281,0.24 10 *b
*a Fully Depressed
*b Fully Released


a.

Turn the ignition switch to ON.


b.

Read the value displayed on the GTS.

Standard Voltage:
Accelerator Pedal Operation Accelerator Position Sensor No.1 Voltage Accelerator Position Sensor No.2 Voltage Difference between Accelerator Position Sensor No.1 Voltage and Accelerator Position Sensor No.2 Voltage
Fully Released 0.5 to 1.1 V 1.2 to 2.0 V Higher than 0.02 V
Fully Depressed 2.6 to 4.5 V 3.4 to 4.75 V


Powertrain > Engine > Data List
Tester Display
Accelerator Position Sensor No.1 Voltage
Accelerator Position Sensor No.2 Voltage
50003 372 87,88

Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL (WITH SENSOR) ROD ASSEMBLY - ECM)
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL (WITH SENSOR) ROD ASSEMBLY - ECM)
a.

Disconnect the accelerator pedal (with sensor) rod assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B17,B2)Location & Routing

Click Connector(B17)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Accelerator Pedal with Sensor Rod Assembly

Click Connector(B2)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B17-4 (VCPA) - B2-55 (VCPA) Always Below 1 Ω
B17-6 (VPA) - B2-53 (VPA) Always Below 1 Ω
B17-5 (EPA) - B2-54 (EPA) Always Below 1 Ω
B17-1 (VCP2) - B2-58 (VCP2) Always Below 1 Ω
B17-3 (VPA2) - B2-56 (VPA2) Always Below 1 Ω
B17-2 (EPA2) - B2-57 (EPA2) Always Below 1 Ω
B17-4 (VCPA) or B2-55 (VCPA) - Body ground and other terminals Always 10 kΩ or higher
B17-6 (VPA) or B2-53 (VPA) - Body ground and other terminals Always 10 kΩ or higher
B17-5 (EPA) or B2-54 (EPA) - Body ground and other terminals Always 10 kΩ or higher
B17-1 (VCP2) or B2-58 (VCP2) - Body ground and other terminals Always 10 kΩ or higher
B17-3 (VPA2) or B2-56 (VPA2) - Body ground and other terminals Always 10 kΩ or higher
B17-2 (EPA2) or B2-57 (EPA2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ACCELERATOR PEDAL POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal (with sensor) rod assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B17)Location & Routing

Click Connector(B17)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Accelerator Pedal with Sensor Rod Assembly

B17-4 (VCPA) - B17-5 (EPA) Ignition switch ON 4.5 to 5.5 V
B17-1 (VCP2) - B17-2 (EPA2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.REPLACE ACCELERATOR PEDAL (WITH SENSOR) ROD ASSEMBLY

NG

4.REPLACE ACCELERATOR PEDAL (WITH SENSOR) ROD ASSEMBLY
a.

Replace the accelerator pedal (with sensor) rod assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL SENSOR DTCS)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P212012, P212014, P21201F, P212512, P212514, P21251F and/or P21382B are output A
DTCs are not output B




A

B

END