The fuel injector assemblies are located on the intake port. They inject fuel into the cylinders based on the signals from the ECM.
Inspect the fuses for circuits related to this system before performing the following procedure.
Disconnect the fuel injector assembly connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C72,C73,C74,C75,C76,C77)Location & Routingewd_type=routing;type=c,c,c,c,c,c;code=C72,C73,C74,C75,C76,C77 |
||
| C72-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C73-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C74-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C75-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C76-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C77-1 - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the fuel injector assembly.
Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL INJECTOR>INSPECTION
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the fuel injector assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C72,C92,C73,C74,C75,C76,C77)Location & Routingewd_type=routing;type=c,c,c,c,c,c,c;code=C72,C92,C73,C74,C75,C76,C77 |
||
| C72-2 - C92-86 (#10) | Always | Below 1 Ω |
| C73-2 - C92-109 (#20) | Always | Below 1 Ω |
| C74-2 - C92-85 (#30) | Always | Below 1 Ω |
| C75-2 - C92-108 (#40) | Always | Below 1 Ω |
| C76-2 - C92-84 (#50) | Always | Below 1 Ω |
| C77-2 - C92-107 (#60) | Always | Below 1 Ω |
| C72-2 or C92-86 (#10) - Body ground and other terminals | Always | 10 kΩ or higher |
| C73-2 or C92-109 (#20) - Body ground and other terminals | Always | 10 kΩ or higher |
| C74-2 or C92-85 (#30) - Body ground and other terminals | Always | 10 kΩ or higher |
| C75-2 or C92-108 (#40) - Body ground and other terminals | Always | 10 kΩ or higher |
| C76-2 or C92-84 (#50) - Body ground and other terminals | Always | 10 kΩ or higher |
| C77-2 or C92-107 (#60) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the relay (IGP NO.2).
Disconnect the fuel injector assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C72,C73,C74,C75,C76,C77)Location & Routingewd_type=routing;type=c,c,c,c,c,c;code=C72,C73,C74,C75,C76,C77 |
||
| 5 (IGP NO.2 relay) - C72-1 | Always | Below 1 Ω |
| 5 (IGP NO.2 relay) - C73-1 | Always | Below 1 Ω |
| 5 (IGP NO.2 relay) - C74-1 | Always | Below 1 Ω |
| 5 (IGP NO.2 relay) - C75-1 | Always | Below 1 Ω |
| 5 (IGP NO.2 relay) - C76-1 | Always | Below 1 Ω |
| 5 (IGP NO.2 relay) - C77-1 | Always | Below 1 Ω |
| 5 (IGP NO.2 relay) or C72-1 - Body ground and other terminals | Always | 10 kΩ or higher |
| 5 (IGP NO.2 relay) or C73-1 - Body ground and other terminals | Always | 10 kΩ or higher |
| 5 (IGP NO.2 relay) or C74-1 - Body ground and other terminals | Always | 10 kΩ or higher |
| 5 (IGP NO.2 relay) or C75-1 - Body ground and other terminals | Always | 10 kΩ or higher |
| 5 (IGP NO.2 relay) or C76-1 - Body ground and other terminals | Always | 10 kΩ or higher |
| 5 (IGP NO.2 relay) or C77-1 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG