Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P261029  ECM/PCM Engine Off Timer Performance Signal Invalid  


DESCRIPTION

The soak timer is built into the ECM. While the engine is running, the ECM monitors the synchronization of the soak timer and the CPU clock. If these two are not synchronized, the ECM will interpret this as a malfunction, illuminates the MIL and store this DTC.

A488684E01
0.146,1.885 1.979,2.083 1.833,0.198 10 false from Battery 2.75,1.583 3.406,1.792 0.656,0.208 10 false IGP NO.1 1.469,2.031 4.625,2.281 3.156,0.25 10 false from Certification ECU (Smart Key ECU Assembly) 3.646,1 4.656,1.198 1.01,0.198 10 false ENG-IGP NO.1 4.448,0.771 5.063,0.969 0.615,0.198 10 false IGP 5,1.125 5.75,1.625 0.75,0.5 10 false Soak Timer IC 4.177,2.896 4.771,3.115 0.594,0.219 10 false +B, +B2 5.063,2.781 5.698,3.531 0.635,0.75 10 false Power Source IC 4.292,3.698 4.906,3.896 0.615,0.198 10 false MREL 5,3.594 5.74,4.25 0.74,0.656 10 false Main Relay Control IC 5.698,4.323 6.156,4.521 0.458,0.198 10 false ECM 2.615,4.135 3.677,4.396 1.063,0.26 10 false EFI MAIN NO.1 1.563,3.563 2.719,3.781 1.156,0.219 10 false EFI MAIN NO. 1 3.76,3.156 4.625,3.406 0.865,0.25 10 false EFI-B NO.1 1.365,2.708 2.354,2.917 0.99,0.208 10 false SUB R/B-NO.1

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P261029 ECM/PCM Engine Off Timer Performance Signal Invalid ECM internal malfunction (2 trip detection logic). ECM Comes on SAE: P2610

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 10 minutes or more.

8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P261029.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

HINT:
·

DTC P261029 is set if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is required.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

2.CHECK WHETHER DTC OUTPUT RECURS (DTC P261029)
2.CHECK WHETHER DTC OUTPUT RECURS (DTC P261029)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

If no pending DTC is output, the repair has been successfully completed.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Proceed to
NEXT



NEXT

END