Home › Power Source / Network › 1GR-FE (BATTERY / CHARGING) › CHARGING SYSTEM
RM38G0E _57 Power Source / Network _101114 1GR-FE BATTERY / CHARGING _0469187 CHARGING SYSTEM G

1GR-FE BATTERY / CHARGING  CHARGING SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced when inspecting battery are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system If the back door is locked and therefore cannot be opened, it is necessary to unlock the back door using the door control switch, electrical key transmitter sub-assembly switch. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.CHECK BATTERY CONDITION

NOTICE:

If the battery is weak or if the engine is difficult to start, recharge the battery and perform inspections again before returning the vehicle to the customer.


a.

Check the battery for damage or deformation. If severe damage, deformation or leakage is found, replace the battery.


b.

Check the electrolyte level in each cell.

·

If the electrolyte level is below the lower line, replace the battery.

·

If the electrolyte level is below the lower line, add distilled water to each cell. Then, recharge the battery and check the electrolyte specific gravity.

Standard Specific Gravity:

1.25 or more at 20°C (68°F)




c.

Check the voltage.

i.

Turn the ignition switch off and turn on the headlights for 20 to 30 seconds. This will remove the surface charge from the battery.


ii.

Measure the battery voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Positive (+) terminal - Negative (-) terminal 20°C (68°F) 12.3 V or higher


If the result is not as specified, recharge or replace the battery.



Hide 3.INSPECT BATTERY TERMINAL AND FUSE

a.

Check whether the battery terminals and engine wire harness are loose or corroded.


b.

Check that the battery terminals are not loose or corroded.

If a terminal is loose or corroded, tighten or clean the terminal.

Torque:
Positive (+) Battery Terminal : 5.0 N*m (51 kgf*cm, 44 in.*lbf)
Negative (-) Battery Terminal : 5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.

Measure the resistance of each fuse for the charging system.

Standard Resistance:

Below 1 Ω


If the result is not as specified, replace the fuse.


Hide 5.INSPECT GENERATOR ASSEMBLY WIRING

a.

Visually check the generator assembly wiring.

i.

Check that the wiring is in good condition.



Hide 6.CHECK FOR ABNORMAL NOISE

a.

Check for abnormal noises from the generator assembly.

i.

Check that no abnormal noises are heard from the generator assembly while the engine is running.

If noise occurs, refer to Problem Symptoms Table.

HINT:

Click herePower Source / Network>1GR-FE (BATTERY / CHARGING)>CHARGING SYSTEM>PROBLEM SYMPTOMS TABLE




Hide 7.INSPECT CHARGING CIRCUIT WITHOUT LOAD

a.
A325166C03
2.313,1.927 2.531,0.448 2.531,0.448 2.719,0.448 false 0.344,2.208 0.656,2.406 0.313,0.198 10 false *1 2.542,2.24 2.854,2.438 0.313,0.198 10 false *2 2.771,0.365 3.083,0.563 0.313,0.198 10 false *a
*1 Battery
*2 Generator Assembly
*a Terminal B


Connect a voltmeter and an ammeter to the charging circuit as follows.

HINT:

If a battery/generator assembly tester is available, connect the tester to the charging circuit in accordance with the manufacturer's instructions.


i.

Disconnect the wire from terminal B of the generator assembly and connect it to the negative (-) lead of the ammeter.


ii.

Connect the ammeter positive (+) lead to terminal B of the generator assembly.


iii.

Connect the voltmeter positive (+) lead to the positive (+) terminal of the battery.


iv.

Ground the voltmeter negative (-) lead.



b.

Check the charging circuit.

i.

Maintain the engine speed at 2000 rpm and check the readings on the ammeter and voltmeter.

Standard Current:
Specified Condition
10 A or higher


Standard Voltage:
Specified Condition
13.5 to 14.35 V


If the result is not as specified, repair or replace the generator assembly.



Hide 8.INSPECT CHARGING CIRCUIT WITH LOAD

a.

With the engine running at 2000 rpm, turn the high beam headlights on and turn the heater blower switch to the "HI" position.


b.

Check the reading on the ammeter.

Standard Current:
Specified Condition
30 A or higher


If the result is not as specified, repair or replace the generator assembly.

HINT:

If the battery is fully charged, the reading will sometimes be less than the standard current. In this case, add more electrical load (operate the wipers, rear window defogger, etc.) and check the reading on the ammeter again.