Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)
RM38G0E _55 Steering _100923 STEERING COLUMN _0469199 STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column)  DISASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (DISASSEMBLY)
C458620N01
4.813,2.792 4.969,2.521 4.969,2.521 5.135,2.521 true 5.938,1.583 5.667,1.583 true 4.792,0.865 4.521,0.865 true 3.385,1.563 3.49,1.854 3.49,1.854 3.688,1.854 true 1.74,0.573 1.906,0.573 1.906,0.573 2.167,1 true 5.104,3.51 5.26,3.51 5.26,3.51 5.385,3.344 true 5.521,3.25 5.906,3.49 0.385,0.24 10 false x 2 4.885,0.26 5.344,0.458 0.458,0.198 10 false x 2 5.458,2.354 5.833,2.667 0.375,0.313 18 false 1 4.854,0.75 5.229,1.063 0.375,0.313 18 false 3 6.094,1.469 6.469,1.781 0.375,0.313 18 false 2 4.823,3.427 5.135,3.635 0.313,0.208 10 false ●*1 1.563,0.479 1.875,0.688 0.313,0.208 10 false *2 3.76,1.76 4.146,1.979 0.385,0.219 10 false ●*3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 STEERING LOCK ACTUATOR WITH ECU ASSEMBLY 45020C (Click here) - -
2 MULTIPLEX TILT AND TELESCOPIC ECU - - - -
3 POWER STEERING ECU WITH MOTOR ASSEMBLY 89650F - - -

*1 STEERING LOCK SET BOLT *2 WIRE HARNESS BRACKET
*3 ELECTRIC POWER STEERING MOTOR SHAFT DAMPER - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

NOTICE:
·

Do not drop the steering lock actuator with ECU assembly, strike it with tools or subject it toimpacts.

·

If the steering lock actuator with ECU assembly is subjected to an impact, replace it with a newone.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 45020C 1.REMOVE STEERING LOCK ACTUATOR WITH ECU ASSEMBLY

a.
C456084C01
4.479,0.573 4.583,0.479 4.583,0.479 4.667,0.479 true 3.656,0.25 3.74,0.25 3.74,0.25 3.781,0.438 true 0.354,0.01 0.635,0.365 0.281,0.354 18 false i 2.875,0.031 3.115,0.313 0.24,0.281 18 true ii 5.438,0.01 6.042,0.333 0.604,0.323 18 true iii, iv 4.698,0.396 5.01,0.594 0.313,0.198 10 false *a 3.365,0.167 3.865,0.448 0.5,0.281 10 false SST
*a Center of the Steering Lock Set Bolt - -


i.

Secure the steering column assembly in a vise between aluminum plates.

NOTICE:
·

Do not overtighten the vise.

·

Do not clamp the steering lock actuator with ECU assembly in the vise.




ii.

Using SST, strike a punch mark for drilling in the center of the steering lock set bolt.

SST
09622-00010  

NOTICE:

When striking the punch mark, in order to prevent impact force from being applied to the steering lock actuator with ECU assembly, do not use a normal center punch.



iii.

Using a drill, drill a hole in 2 steering lock set bolts and insert a screw extractor.


iv.

Using the screw extractor, remove the 2 steering lock set bolts and steering lock actuator with ECU assembly.

NOTICE:

Push in the screw extractor by hand, and do not strike it with tools, etc.




Hide 2.REMOVE MULTIPLEX TILT AND TELESCOPIC ECU

a.
C456085


Hide 89650F 3.REMOVE POWER STEERING ECU WITH MOTOR ASSEMBLY

a.
C456733C01
3.604,2.885 3.917,2.667 3.917,2.667 4.083,2.667 true 4.083,3.417 4.417,3.417 true 4.135,2.573 4.448,2.771 0.313,0.198 10 false *2 4.5,3.323 4.813,3.521 0.313,0.198 10 false *1
*1 Power Steering ECU With Motor Assembly *2 Electric Power Steering Motor Shaft Damper
V100135

Bolt
V100136

Connector