Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)
RM38G0E _55 Steering _100923 STEERING COLUMN _0469199 STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column)  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (DISASSEMBLY)
C488732N02
5.25,0.25 6.083,0.417 0.833,0.167 0.333,1.125 1.167,1.292 0.833,0.167 5.427,3.344 5.583,3.073 5.583,3.073 5.75,3.073 true 5.917,1.594 5.646,1.594 true 4.823,0.885 4.552,0.885 true 4.781,2.76 4.938,2.5 4.938,2.5 5.104,2.5 true 5.25,0.333 4.802,0.333 true 2.24,1.073 2.396,0.802 2.396,0.802 2.563,0.802 true 1.438,1.208 1.167,1.208 true 3.406,1.563 3.583,1.896 3.583,1.896 3.75,1.896 true 5.531,3.281 5.99,3.479 0.458,0.198 10 false x 2 4.792,0.385 5.25,0.583 0.458,0.198 10 false x 2 5.99,1.448 6.365,1.76 0.375,0.313 18 false 3 4.219,1.781 4.594,2.094 0.375,0.313 18 false 1 5.188,0.76 5.563,1.073 0.375,0.313 18 false 2 5.792,3 6.25,3.25 0.458,0.25 10 false ●*1 2.604,0.75 2.979,0.99 0.375,0.24 10 false *2 5.302,0.26 6.333,0.5 1.031,0.24 8 false 18.5 (189, 14) 4.073,1.823 4.333,2.104 0.26,0.281 10 false ● 5.417,2.365 5.792,2.677 0.375,0.313 18 false 4 0.385,1.135 1.417,1.375 1.031,0.24 8 false 18.5 (189, 14)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 ELECTRIC POWER STEERING MOTOR SHAFT DAMPER 45254B (Click here) - -
2 POWER STEERING ECU WITH MOTOR ASSEMBLY 89650F (Click here) - -
3 MULTIPLEX TILT AND TELESCOPIC ECU - - - -
4 STEERING LOCK ACTUATOR WITH ECU ASSEMBLY 45020C (Click here) - -

*1 STEERING LOCK SET BOLT *2 WIRE HARNESS BRACKET
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

Grease - -

CAUTION / NOTICE / HINT

NOTICE:
·

Do not drop the steering lock actuator with ECU assembly, strike it with tools or subject it to impacts.

·

If the steering lock actuator with ECU assembly is subjected to an impact, replace it with a newone.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 45254B 1.INSTALL ELECTRIC POWER STEERING MOTOR SHAFT DAMPER

a.
C488733C02
0.427,0.073 0.74,0.458 0.313,0.385 18 false i 3.615,0.115 4.167,0.469 0.552,0.354 18 false ii
V100135

Grease - -


i.

Apply grease to a new electric power steering motor shaft damper.

NOTICE:

First wipe off the existing grease from the serrated part, and then apply the dedicated grease supplied with a new power steering ECU with motor assembly or electric power steering column sub-assembly.



ii.

Install the electric power steering motor shaft damper to the electric power steering column sub-assembly.



Hide 89650F 2.INSTALL POWER STEERING ECU WITH MOTOR ASSEMBLY

Z101186

NOTICE:
·

Do not drop the power steering ECU with motor assembly, strike it with tools or subject it to impacts.

·

If the power steering ECU with motor assembly is subjected to an impact, replace it with a new one.

·

Do not pull the wire harness of the electric power steering column sub-assembly.

·

Do not allow any moisture to come into contact with the power steering ECU with motor assembly.

·

Do not loosen any bolts not mentioned in the procedure.

·

Do not allow any foreign matter to contaminate the power steering ECU with motor assembly.




a.
C488734C02
2.24,2.938 2.573,2.938 true 2.24,3.083 2.583,3.083 2.583,3.083 2.583,2.802 true 2.24,2.802 2.833,2.802 true 0.813,2.917 1.146,2.917 true 2.896,2.729 3.208,2.927 0.313,0.198 10 false *a 0.625,2.844 0.938,3.042 0.313,0.198 10 false *b 0.406,2.052 0.938,2.469 0.531,0.417 18 false iii 4.146,0.083 4.677,0.5 0.531,0.417 18 false ii 4.146,1.99 4.531,2.375 0.385,0.385 18 false iv 0.385,0.083 0.74,0.396 0.354,0.313 18 false i
*a Wooden Block *b Cloth


i.

Temporarily install the power steering ECU with motor assembly to the electric power steering column sub-assembly with the 2 bolts.

NOTICE:

When temporarily installing the 2 bolts to the power steering ECU with motor assembly, do not tighten them all the way down.



ii.

Using a 10 mm hexagon socket wrench, install the steering wheel assembly set bolt to the steering main shaft.

NOTICE:

Do not apply excessive torque to the steering wheel assembly set bolt by using a tool such as an impact wrench.


HINT:

The steering wheel assembly set bolt is used for turning the steering main shaft during inspection of the steering main shaft rotating torque.

Remove the steering wheel assembly set bolt after performing this inspection.



iii.

Secure the steering column assembly in a vise using aluminum plates, cloths and wooden blocks.

NOTICE:
·

Do not overtighten the vise, as the steering column assembly may become deformed.

·

Secure the power steering ECU with motor assembly so that it is upright.

·

Support the steering column assembly with wooden blocks or similar items to ensure that it does not fall.




iv.

Rotate the steering main shaft 180 degrees counterclockwise and then 180 degrees clockwise at a speed of 60 rpm, and repeat 2 to 3 times to center the axis of the power steering ECU with motor assembly. [*1]



b.
C488735N02
0.135,2.188 0.969,2.542 0.833,0.354 18 false iv 4.135,0.083 4.74,0.448 0.604,0.365 18 false ii, iii 0.167,0.104 0.583,0.49 0.417,0.385 18 false i 4.073,2.208 4.49,2.594 0.417,0.385 18 false v

i.

Tighten the 2 bolts. [*2]

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


ii.

Using a torque wrench, measure the turning torque of the steering main shaft.

Preload:

0.6 to 1.4 N*m (7 to 14 kgf*cm, 6 to 12 in.*lbf)


NOTICE:

Ensure that there is no abnormal resistance during rotation.


If the turning torque is not as specified, loosen the 2 bolts and repeat steps [*1] and [*2] to recenter the axis of the power steering ECU with motor assembly.


iii.

Remove the steering wheel assembly set bolt.


iv.

Connect the connector.


v.

Install the wire harness bracket with the bolt.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)



Hide 3.INSTALL MULTIPLEX TILT AND TELESCOPIC ECU

Hide 45020C 4.INSTALL STEERING LOCK ACTUATOR WITH ECU ASSEMBLY

Z101186

NOTICE:

If the steering lock actuator with ECU assembly is replaced, refer to Service Bulletin.



a.
C456087N01
0.573,0.24 0.823,0.594 0.25,0.354 18 false i 4.427,0.219 4.677,0.573 0.25,0.354 18 false ii

i.

Secure the steering column assembly in a vise between aluminum plates.

NOTICE:
·

Do not overtighten the vise.

·

Do not clamp the steering lock actuator with ECU assembly in the vise.




ii.

Install the steering lock actuator with ECU assembly with 2 new steering lock set bolts, and tighten the bolts until they break off.