| *1 | NO. 1 BREATHER PLUG (ATM) | *2 | NO. 2 BREATHER PLUG (ATM) |
| *3 | BREATHER PLUG HOSE | - | - |
| ● | Non-reusable part | ★ | Precoated part |
| *1 | STRAIGHT PIN | - | - |
| ● | Non-reusable part | ★ | Precoated part |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 14 | AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY | 35106 | ( ) |
- | - |
| 15 | TRANSMISSION OIL CLEANER MAGNET | 35394 | ( ) |
- | - |
| 16 | TRANSMISSION WIRE | 82125J | - | - | - |
| *1 | AUTOMATIC TRANSMISSION OIL PAN GASKET | *2 | TEMPERATURE SENSOR CLAMP |
| *3 | DRAIN PLUG | *4 | OVERFLOW PLUG |
| *5 | TEMPERATURE SENSOR | - | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 17 | VALVE BODY OIL STRAINER ASSEMBLY | 35330 | - | - | - |
| 18 | TRANSMISSION VALVE BODY ASSEMBLY | 35410 | - | - | - |
| 19 | TRANSMISSION CASE GASKET | 35145C | - | - | - |
| 20 | BRAKE DRUM GASKET | 35159 | - | - | - |
| *1 | DETENT SPRING | *2 | DETENT SPRING COVER |
| ● | Non-reusable part | - | - |
| *1 | PARKING LOCK PAWL | *2 | SPRING |
| *3 | SPRING PIN | *4 | MANUAL VALVE LEVER SHAFT |
| ● | Non-reusable part | - | - |
| *1 | THRUST BEARING RACE | *2 | THRUST NEEDLE ROLLER BEARING |
| *3 | INPUT SHAFT SUB-ASSEMBLY | - | - |
| ● | Non-reusable part | - | - |
| *1 | NO. 1 CLUTCH PLATE | *2 | FORWARD CLUTCH FLANGE |
| ● | Non-reusable part | - | - |
| *1 | NO. 2 CLUTCH PLATE | *2 | DIRECT CLUTCH FLANGE |
| ● | Non-reusable part | - | - |
| *1 | THRUST BEARING RACE | *2 | THRUST NEEDLE ROLLER BEARING |
| *1 | THRUST BEARING RACE | *2 | THRUST NEEDLE ROLLER BEARING |
| *3 | FRONT PLANETARY RING GEAR | *4 | NO. 2 BRAKE CYLINDER |
| ● | Non-reusable part | - | - |
| *1 | NO. 2 BRAKE PLATE | *2 | NO. 2 BRAKE FLANGE |
| *3 | THRUST BEARING RACE | *4 | THRUST NEEDLE ROLLER BEARING |
| *5 | CENTER PLANETARY RING GEAR FLANGE | - | - |
| *1 | NO. 1 BRAKE PLATE | *2 | NO. 1 BRAKE FLANGE |
| *3 | NO. 1 BRAKE CYLINDER | - | - |
| ● | Non-reusable part | - | - |
| *1 | THRUST BEARING RACE | *2 | THRUST NEEDLE ROLLER BEARING |
| *1 | NO. 4 BRAKE PLATE | *2 | NO. 4 BRAKE FLANGE |
| *3 | THRUST BEARING RACE | *4 | THRUST NEEDLE ROLLER BEARING |
| ● | Non-reusable part | - | - |
1.REMOVE TRANSMISSION BREATHER HOSE ASSEMBLY
89413N 2.REMOVE TRANSMISSION REVOLUTION SENSOR (NT)
89413W 3.REMOVE TRANSMISSION REVOLUTION SENSOR (SP2)
35572 4.REMOVE TRANSMISSION CONTROL SHAFT LEVER RH
84540 5.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
Using a screwdriver, bend the tabs of the lock washer.
Remove the nut and lock washer.
Remove the bolt and park/neutral position switch assembly from the automatic transmission case sub-assembly.
Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch assembly as the detent spring may become detached from the manual valve lever shaft.
35015X 6.REMOVE REFILL PLUG
35104A 7.REMOVE AUTOMATIC TRANSMISSION CASE PLUG
Remove the 6 automatic transmission case plugs from the automatic transmission case sub-assembly.
Remove the 6 O-rings from the 6 automatic transmission case plugs.
Using a T55 "TORX" socket wrench, remove the automatic transmission case plug from the automatic transmission case sub-assembly.
Remove the O-ring from the automatic transmission case plug.
8.REMOVE OIL COOLER TUBE UNION
| *a | Turn | *b | Hold |
Remove the 2 oil cooler tube unions from the automatic transmission case sub-assembly.
Remove the 2 O-rings from the 2 oil cooler tube unions.
35015G 9.REMOVE REAR TRANSFER ADAPTER SUB-ASSEMBLY
Remove the 10 bolts and transfer adapter sub-assembly from the automatic transmission case sub-assembly.
Use a brass bar and hammer to remove the transfer adapter sub-assembly.
Remove the 2 straight pins from the transfer adapter sub-assembly.
It is not necessary to remove the straight pins unless they are being replaced.
36117A 10.REMOVE TRANSFER ADAPTER OIL SEAL
Using a screwdriver, pry out the transfer adapter oil seal from the transfer adapter sub-assembly.
Be careful not to damage the transfer adapter sub-assembly.
Tape the screwdriver tip before use.
35015F 11.REMOVE TRANSFER ADAPTER HOLE SNAP RING
Using snap ring pliers, remove the snap ring from the transfer adapter sub-assembly.
35111 12.REMOVE AUTOMATIC TRANSMISSION HOUSING
35104 13.SECURE AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY
Install the automatic transmission case sub-assembly to an overhaul attachment.
35106 14.REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY
|
|
Using a 5 mm socket hexagon wrench, remove the overflow plug and gasket.
Remove the drain plug and gasket.
Remove the 10 bolts, automatic transmission oil pan sub-assembly and automatic transmission oil pan gasket.
35394 15.REMOVE TRANSMISSION OIL CLEANER MAGNET
Remove the 4 transmission oil cleaner magnets from the automatic transmission oil pan sub-assembly.
Examine the particles in the automatic transmission oil pan sub-assembly.
Collect any steel chips with the removed transmission oil cleaner magnets. Carefully inspect the foreign matter and particles in the automatic transmission oil pan sub-assembly and on the transmission oil cleaner magnets to anticipate the type of wear you will find in the automatic transmission assembly.
Steel (magnetic): bearing, gear and clutch plate wear
Brass (non-magnetic): bush wear
82125J 16.REMOVE TRANSMISSION WIRE
| *1 | Temperature Sensor Clamp | *2 | Temperature Sensor |
|
Bolt |
|
Connector |
|
O-ring | - | - |
35330 17.REMOVE VALVE BODY OIL STRAINER ASSEMBLY
35410 18.REMOVE TRANSMISSION VALVE BODY ASSEMBLY
35145C 19.REMOVE TRANSMISSION CASE GASKET
35159 20.REMOVE BRAKE DRUM GASKET
35595 21.REMOVE PARKING LOCK PAWL BRACKET
35501 22.REMOVE PARKING LOCK ROD SUB-ASSEMBLY
35556 23.REMOVE PARKING LOCK PAWL SHAFT
| *1 | Parking Lock Pawl | *2 | E-ring |
| *3 | Parking Lock Pawl Shaft | *4 | Spring |
Pull out the parking lock pawl shaft from the front side, and remove the parking lock pawl and spring.
Remove the E-ring from the parking lock pawl shaft.
35505 24.REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY
Using a screwdriver and hammer, cut off the spacer and remove it from the manual valve lever shaft.
Be careful not to damage the manual valve lever shaft.
Tape the screwdriver tip before use.
Using a 3 mm pin punch and hammer, drive out the spring pin.
Slowly drive out the spring pin so that it does not fall into the automatic transmission case sub-assembly.
Pull the manual valve lever shaft out through the case and remove the manual valve lever sub-assembly.
35506F 25.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL
Using a screwdriver, pry out the 2 manual valve lever shaft oil seals from the automatic transmission case sub-assembly.
Be careful not to damage the automatic transmission case sub-assembly.
Tape the screwdriver tip before use.
26.REMOVE OIL PUMP ASSEMBLY
| *1 | Thrust Bearing Race | *2 | Thrust Needle Roller Bearing |
| *3 | Oil Pump O-ring | *4 | Oil Pump Assembly |
|
Turn | - | - |
Remove the 10 bolts.
Using SST, pull out the oil pump assembly from the automatic transmission case sub-assembly.
Remove the thrust bearing race and thrust needle roller bearing from the oil pump assembly.
Remove the oil pump O-ring from the oil pump assembly.
27.REMOVE DIRECT CLUTCH DRUM AND INPUT SHAFT ASSEMBLY
35605A 28.REMOVE DIRECT CLUTCH DRUM SUB-ASSEMBLY
35617 30.REMOVE CLUTCH DRUM OIL SEAL RING
35633B 31.REMOVE NO. 1 CLUTCH DISC (FORWARD CLUTCH DISC)
| *1 | Forward Clutch Flange | *2 | No. 1 Clutch Disc |
| *3 | No. 1 Clutch Plate | - | - |
Secure the input shaft sub-assembly in a vise between aluminum plates.
Do not overtighten the vise.
Using a screwdriver, remove the snap ring.
Be careful not to damage the input shaft sub-assembly.
Tape the screwdriver tip before use.
Remove the forward clutch flange, 5 No. 1 clutch discs and 5 No. 1 clutch plates from the input shaft sub-assembly.
35668 33.REMOVE NO. 1 CLUTCH BALANCER
| *1 | No. 1 Clutch Balancer | *2 | Forward Clutch Return Spring Sub-assembly |
| *3 | Input Shaft Sub-assembly | *4 | O-ring |
Place SST on the No. 1 clutch balancer, and compress the forward clutch return spring sub-assembly with a press.
Using SST, remove the snap ring.
Remove the No. 1 clutch balancer and forward clutch return spring sub-assembly from the input shaft sub-assembly.
Remove the O-ring from the No. 1 clutch balancer.
35612B 35.REMOVE FORWARD CLUTCH PISTON
| *1 | Forward Clutch Piston | *2 | Input Shaft Sub-assembly |
| *3 | O-ring | - | - |
| *a | Oil Hole | - | - |
While holding the forward clutch piston, apply compressed air to the oil hole of the input shaft sub-assembly to remove the forward clutch piston from the input shaft sub-assembly.
Remove the O-ring from the forward clutch piston.
Remove the O-ring from the input shaft sub-assembly.
35667A 38.REMOVE NO. 2 CLUTCH DISC (DIRECT CLUTCH DISC)
| *1 | Direct Clutch Flange | *2 | No. 2 Clutch Disc |
| *3 | No. 2 Clutch Plate | - | - |
Using a screwdriver, remove the snap ring from the direct clutch drum sub-assembly.
Be careful not to damage the direct clutch drum sub-assembly.
Tape the screwdriver tip before use.
Remove the direct clutch flange, 5 No. 2 clutch discs and 5 No. 2 clutch plates from the direct clutch drum sub-assembly.
35669 40.REMOVE NO. 2 CLUTCH BALANCER
| *1 | No. 2 Clutch Balancer | *2 | Direct Clutch Return Spring Sub-assembly |
| *3 | Direct Clutch Drum Sub-assembly | *4 | O-ring |
Place SST on the No. 2 clutch balancer, and compress the direct clutch return spring sub-assembly with a press.
Using SST, remove the snap ring.
Remove the No. 2 clutch balancer and direct clutch return spring sub-assembly from the direct clutch drum sub-assembly.
Remove the O-ring from the No. 2 clutch balancer.
35652C 42.REMOVE DIRECT CLUTCH PISTON
| *1 | Oil Pump Assembly | *2 | Torque Converter Assembly |
| *3 | Direct Clutch Piston | *4 | O-ring |
| *a | Oil Hole | - | - |
Place the oil pump assembly onto the torque converter assembly, and then place the direct clutch drum sub-assembly onto the oil pump assembly.
While holding the direct clutch piston, apply compressed air to the oil hole of the oil pump assembly to remove the direct clutch piston from the direct clutch drum sub-assembly.
Remove the 2 O-rings from the direct clutch piston.
35631 44.REMOVE MULTIPLE DISC CLUTCH HUB
35061 45.REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY
35709J 47.REMOVE SUN GEAR INPUT DRUM SUB-ASSEMBLY
35720 49.REMOVE FRONT PLANETARY GEAR ASSEMBLY
35743 51.REMOVE FRONT PLANETARY RING GEAR WITH FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY
35076C 52.REMOVE FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY
| *1 | Front Planetary Ring Gear | *2 | Snap Ring |
| *3 | Front Planetary Ring Gear Flange Sub-assembly | - | - |
Using needle-nose pliers, remove the snap ring and front planetary ring gear flange sub-assembly from the front planetary ring gear.
35699 55.REMOVE NO. 2 BRAKE CYLINDER WITH NO. 2 BRAKE PISTON
| *1 | No. 2 Brake Cylinder with No. 2 Brake Piston | *2 | No. 2 Brake Piston Return Spring Sub-assembly |
|
Turn | - | - |
Place SST on the No. 2 brake cylinder, and compress the No. 2 brake piston return spring sub-assembly with a press.
Using a screwdriver, remove the snap ring from the automatic transmission case sub-assembly.
Be careful not to damage the automatic transmission case sub-assembly.
Tape the screwdriver tip before use.
Remove the No. 2 brake cylinder with No. 2 brake piston and No. 2 brake piston return spring sub-assembly from the automatic transmission case sub-assembly.
35622G 57.REMOVE NO. 2 BRAKE PISTON
| *1 | No. 2 Brake Piston | *2 | O-ring |
While holding the No. 2 brake piston, apply compressed air to the oil hole of the No. 2 brake cylinder to remove the No. 2 brake piston from the No. 2 brake cylinder.
Remove the 2 O-rings from the No. 2 brake piston.
35682A 58.REMOVE NO. 2 BRAKE DISC
| *1 | No. 2 Brake Flange | *2 | No. 2 Brake Disc |
| *3 | No. 2 Brake Plate | - | - |
35769 60.REMOVE CENTER PLANETARY RING GEAR FLANGE WITH CENTER PLANETARY RING GEAR
35763 61.REMOVE CENTER PLANETARY RING GEAR
| *1 | Center Planetary Ring Gear Flange | *2 | Center Planetary Ring Gear |
Using a screwdriver, remove the snap ring from the center planetary ring gear flange with center planetary ring gear.
Be careful not to damage the center planetary ring gear flange with center planetary ring gear.
Tape the screwdriver tip before use.
Remove the center planetary ring gear from the center planetary ring gear flange.
35750 62.REMOVE CENTER PLANETARY GEAR ASSEMBLY
35719B 64.REMOVE PLANETARY SUN GEAR
35681A 66.REMOVE NO. 1 BRAKE DISC
| *1 | No. 1 Brake Flange | *2 | No. 1 Brake Disc |
| *3 | No. 1 Brake Plate | - | - |
Using a screwdriver, remove the snap ring from the automatic transmission case sub-assembly.
Be careful not to damage the automatic transmission case sub-assembly.
Tape the screwdriver tip before use.
Remove the No. 1 brake flange, 4 No. 1 brake discs and 4 No. 1 brake plates from the automatic transmission case sub-assembly.
35698 68.REMOVE NO. 1 BRAKE CYLINDER WITH NO. 1 BRAKE PISTON
| *1 | No. 1 Brake Piston Return Spring Sub-assembly | *2 | No. 1 Brake Cylinder with No. 1 Brake Piston |
|
Turn | - | - |
Place SST on the No. 1 brake piston return spring sub-assembly, and compress the No. 1 brake piston return spring sub-assembly with a press.
Using a screwdriver, remove the snap ring from the automatic transmission case sub-assembly.
Be careful not to damage the automatic transmission case sub-assembly.
Tape the screwdriver tip before use.
Remove the No. 1 brake piston return spring sub-assembly and No. 1 brake cylinder with No. 1 brake piston from the automatic transmission case sub-assembly.
35621V 70.REMOVE NO. 1 BRAKE PISTON
| *1 | No. 1 Brake Piston | *2 | O-ring |
While holding the No. 1 brake piston, apply compressed air to the oil hole of the No. 1 brake cylinder to remove the No. 1 brake piston from the No. 1 brake cylinder.
Remove the 2 O-rings from the No. 1 brake piston.
35713 72.REMOVE INTERMEDIATE SHAFT WITH NO. 3 ONE-WAY CLUTCH ASSEMBLY AND REAR PLANETARY RING GEAR
Using SST, remove the snap ring from the automatic transmission case sub-assembly.
Remove the intermediate shaft with No. 3 one-way clutch assembly and rear planetary ring gear from the automatic transmission case sub-assembly.
35770C 74.REMOVE NO. 3 ONE-WAY CLUTCH ASSEMBLY WITH ONE-WAY CLUTCH INNER RACE
35797B 75.REMOVE ONE-WAY CLUTCH INNER RACE
35077D 76.REMOVE REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY WITH REAR PLANETARY RING GEAR
35761 79.REMOVE REAR PLANETARY RING GEAR
| *1 | Rear Planetary Ring Gear Flange Sub-assembly | *2 | Rear Planetary Ring Gear |
Using a screwdriver, remove the snap ring from the rear planetary ring gear flange sub-assembly with rear planetary ring gear.
Be careful not to damage the rear planetary ring gear flange sub-assembly with rear planetary ring gear.
Tape the screwdriver tip before use.
Remove the rear planetary ring gear flange sub-assembly from the rear planetary ring gear.
35760 80.REMOVE REAR PLANETARY GEAR ASSEMBLY WITH NO. 4 BRAKE DISC
35684 82.REMOVE NO. 4 BRAKE DISC
| *1 | No. 4 Brake Flange | *2 | No. 4 Brake Disc |
| *3 | No. 4 Brake Plate | - | - |
35623H 84.REMOVE 1ST AND REVERSE BRAKE PISTON
| *1 | 1st and Reverse Brake Return Spring Sub-assembly | *2 | 1st and Reverse Brake Piston |
| *3 | O-ring | - | - |
Place SST on the 1st and reverse brake return spring sub-assembly and compress the 1st and reverse brake return spring sub-assembly.
Using SST, remove the snap ring from the automatic transmission case sub-assembly.
Remove the 1st and reverse brake return spring sub-assembly from the automatic transmission case sub-assembly.
Apply compressed air to the oil hole of the automatic transmission case sub-assembly to remove the 1st and reverse brake piston from the automatic transmission case sub-assembly.
Remove the O-ring from the 1st and reverse brake piston.
35626 86.REMOVE BRAKE REACTION SLEEVE
| *1 | Brake Reaction Sleeve | *2 | O-ring |
Using SST, remove the brake reaction sleeve from the automatic transmission case sub-assembly.
Remove the 2 O-rings from the brake reaction sleeve.
35629A 87.REMOVE NO. 4 BRAKE PISTON
| *1 | No. 4 Brake Piston | *2 | O-ring |
Using SST, remove the No. 4 brake piston from the automatic transmission case sub-assembly.
Remove the 2 O-rings from the No. 4 brake piston.
35639B 88.REMOVE BRAKE PLATE STOPPER SPRING