| *1 | 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY | - | - |
| ● | Non-reusable part |
|
Toyota Genuine ATF WS |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 6 | REAR PLANETARY GEAR ASSEMBLY | 35760 | ( ) |
- | - |
| 7 | NO. 4 BRAKE DISC | 35684 | ( ) |
- | - |
| *1 | NO. 4 BRAKE PLATE | *2 | NO. 4 BRAKE FLANGE |
| *3 | THRUST BEARING RACE | *4 | THRUST NEEDLE ROLLER BEARING |
|
Toyota Genuine ATF WS | - | - |
| *1 | THRUST BEARING RACE | *2 | THRUST NEEDLE ROLLER BEARING |
| *3 | NO. 3 ONE-WAY CLUTCH ASSEMBLY | *4 | REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY |
|
Toyota Genuine ATF WS | - | - |
| *1 | NO. 1 BRAKE PLATE | *2 | NO. 1 BRAKE FLANGE |
| *3 | NO. 1 BRAKE CYLINDER | - | - |
| ● | Non-reusable part |
|
Toyota Genuine ATF WS |
| *1 | NO. 2 BRAKE PLATE | *2 | NO. 2 BRAKE FLANGE |
| *3 | THRUST BEARING RACE | *4 | THRUST NEEDLE ROLLER BEARING |
| *5 | CENTER PLANETARY RING GEAR FLANGE | - | - |
|
Toyota Genuine ATF WS | - | - |
| *1 | THRUST BEARING RACE | *2 | THRUST NEEDLE ROLLER BEARING |
| *3 | FRONT PLANETARY RING GEAR | *4 | NO. 2 BRAKE CYLINDER |
| *5 | NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY | - | - |
| ● | Non-reusable part |
|
Toyota Genuine ATF WS |
| *1 | THRUST BEARING RACE | *2 | THRUST NEEDLE ROLLER BEARING |
|
Toyota Genuine ATF WS | - | - |
| *1 | NO. 2 CLUTCH PLATE | *2 | DIRECT CLUTCH FLANGE |
| *3 | DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY | *4 | DIRECT CLUTCH DRUM SUB-ASSEMBLY |
| ● | Non-reusable part |
|
Toyota Genuine ATF WS |
| *1 | NO. 1 CLUTCH PLATE | *2 | FORWARD CLUTCH FLANGE |
| *3 | FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY | *4 | INPUT SHAFT SUB-ASSEMBLY |
| ● | Non-reusable part |
|
Toyota Genuine ATF WS |
| *1 | THRUST BEARING RACE | *2 | THRUST NEEDLE ROLLER BEARING |
| *3 | INPUT SHAFT SUB-ASSEMBLY | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
Toyota Genuine ATF WS | - | - |
| *1 | PARKING LOCK PAWL | *2 | SPRING |
| *3 | SPRING PIN | *4 | MANUAL VALVE LEVER SHAFT |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
|
MP grease | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 50 | BRAKE DRUM GASKET | 35159 | ( ) |
- | - |
| 51 | TRANSMISSION CASE GASKET | 35145C | ( ) |
- | - |
| 52 | TRANSMISSION VALVE BODY ASSEMBLY | 35410 | ( ) |
- | - |
| 53 | VALVE BODY OIL STRAINER ASSEMBLY | 35330 | ( ) |
- | - |
| *1 | DETENT SPRING | *2 | DETENT SPRING COVER |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
Toyota Genuine ATF WS | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 54 | TRANSMISSION WIRE | 82125J | ( ) |
- | - |
| 55 | TRANSMISSION OIL CLEANER MAGNET | 35394 | - | - | - |
| 56 | AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY | 35106 | ( ) |
- | - |
| *1 | AUTOMATIC TRANSMISSION OIL PAN GASKET | *2 | TEMPERATURE SENSOR CLAMP |
| *3 | DRAIN PLUG | *4 | OVERFLOW PLUG |
| *5 | TEMPERATURE SENSOR | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
Toyota Genuine ATF WS | - | - |
| *1 | STRAIGHT PIN | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
Toyota Genuine Adhesive 1344 |
|
MP grease |
| ★ | Precoated part | - | - |
| *1 | NO. 1 BREATHER PLUG (ATM) | *2 | NO. 2 BREATHER PLUG (ATM) |
| *3 | BREATHER PLUG HOSE | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |
|
Toyota Genuine ATF WS |
|
Toyota Genuine Adhesive 1344 | ★ | Precoated part |
1. BEARING POSITION
| Mark | Front Race Diameter Inside / Outside (mm (in.)) | Thrust Bearing Diameter Inside / Outside (mm (in.)) | Rear Race Diameter Inside / Outside (mm (in.)) |
|---|---|---|---|
| A | 74.2 (2.921) / 87.74 (3.454) | 71.9 (2.831) / 85.6 (3.370) | - |
| B | 40.0 (1.575) / 52.8 (2.079) | 34.6 (1.362) / 52.0 (2.047) | - |
| C | - | 21.3 (0.839) / 41.1 (1.618) | 22.6 (0.889) / 44.8 (1.764) |
| D | 38.4 (1.512) / 56.5 (2.224) | 33.3 (1.311) / 56.6 (2.228) | - |
| E | - | 39.6 (1.559) / 52.8 (2.079) | 40.83 (1.607) / 52.8 (2.079) |
| F | - | 37.1 (1.461) / 61.2 (2.409) | 44.0 (1.732) / 62.8 (2.472) |
| G | 65.8 (2.591) / 86.3 (3.398) | 63.3 (2.492) / 78.8 (3.102) | - |
| H | 66.3 (2.610) / 78.9 (3.106) | 63.3 (2.492) / 78.8 (3.102) | - |
| I | - | 55.7 (2.193) / 76.4 (3.008) | 53.7 (2.114) / 74.0 (2.913) |
| J | 33.4 (1.315) / 49.0 (1.929) | 32.1 (1.264) / 49.35 (1.943) | 32.1 (1.264) / 49.0 (1.929) |
| K | - | 21.0 (0.827) / 41.5 (1.634) | 23.13 (0.911) / 41.5 (1.634) |
| L | - | 43.55 (1.715) / 61.0 (2.402) | 47.1 (1.854) / 67.1 (2.642) |
35639B 2.INSTALL BRAKE PLATE STOPPER SPRING
Install the 2 brake plate stopper springs to the automatic transmission case sub-assembly.
The shapes of the parts are different. Refer to the illustration when installing the parts.
35629A 3.INSTALL NO. 4 BRAKE PISTON
| *1 | No. 4 Brake Piston | *2 | O-ring |
Coat 2 new O-rings with ATF, and install them to the No. 4 brake piston.
Install the No. 4 brake piston to the brake reaction sleeve.
Be careful not to damage the O-rings.
35626 4.INSTALL BRAKE REACTION SLEEVE
| *1 | Brake Reaction Sleeve | *2 | O-ring |
Coat 2 new O-rings with ATF, and install them to the brake reaction sleeve.
With the No. 4 brake piston underneath (the rear side), install the brake reaction sleeve and No. 4 brake piston to the automatic transmission case sub-assembly.
Be careful not to damage the O-rings.
35623H 5.INSTALL 1ST AND REVERSE BRAKE PISTON
| *1 | 1st and Reverse Brake Return Spring Sub-assembly | *2 | 1st and Reverse Brake Piston |
| *3 | O-ring | - | - |
Coat a new O-ring with ATF, and install it to the 1st and reverse brake piston.
Install the 1st and reverse brake piston to the automatic transmission case sub-assembly while making sure that the protrusion of the 1st and reverse brake piston is positioned as shown in the illustration.
Be careful not to damage the O-ring.
Install the 1st and reverse brake return spring sub-assembly to the automatic transmission case sub-assembly.
Place the 1st and reverse brake return spring sub-assembly onto the 1st and reverse brake piston.
Place SST on the 1st and reverse brake return spring sub-assembly, and compress the 1st and reverse brake return spring sub-assembly.
Using a screwdriver, install the snap ring to the automatic transmission case sub-assembly.
Be careful not to damage the 1st and reverse brake return spring sub-assembly and automatic transmission case sub-assembly.
Tape the screwdriver tip before use.
35760 6.INSTALL REAR PLANETARY GEAR ASSEMBLY
| *1 | Thrust Needle Roller Bearing K | *2 | Thrust Bearing Race K |
| *3 | Thrust Needle Roller Bearing L | *4 | Thrust Bearing Race L |
Coat the thrust bearing race with ATF and install it to the automatic transmission case sub-assembly.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Needle Roller Bearing K | 21.0 (0.827) | 41.5 (1.634) |
| Thrust Bearing Race K | 23.13 (0.911) | 41.5 (1.634) |
| Thrust Needle Roller Bearing L | 43.55 (1.715) | 61.0 (2.402) |
| Thrust Bearing Race L | 47.1 (1.854) | 67.1 (2.642) |
Be sure to install the thrust needle roller bearing and thrust bearing race in the correct direction.
Coat the 2 thrust needle roller bearings and thrust bearing races with ATF and install them to the rear planetary gear assembly.
Install the rear planetary gear assembly to the automatic transmission case sub-assembly.
35684 7.INSTALL NO. 4 BRAKE DISC
| *1 | No. 4 Brake Flange | *2 | No. 4 Brake Disc |
| *3 | No. 4 Brake Plate | - | - |
Install the 2 No. 4 brake flanges, 7 No. 4 brake discs and 6 No. 4 brake plates to the automatic transmission case sub-assembly.
Make sure that the No. 4 brake discs, No. 4 brake plates and No. 4 brake flanges are installed in the correct order.
Install the thicker No. 4 brake flange first, and then install the thinner one.
35713 8.INSTALL INTERMEDIATE SHAFT
| *1 | Thrust Needle Roller Bearing J | *2 | Thrust Bearing Race J (Rear Race) |
Coat the thrust needle roller bearing and thrust bearing race with ATF and install them to the intermediate shaft.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Needle Roller Bearing J | 32.1 (1.264) | 49.35 (1.943) |
| Thrust Bearing Race J (Rear Race) |
32.1 (1.264) | 49.0 (1.929) |
Install the intermediate shaft to the automatic transmission case sub-assembly.
35761 9.INSTALL REAR PLANETARY RING GEAR
| *1 | Rear Planetary Ring Gear Flange Sub-assembly | *2 | Rear Planetary Ring Gear |
Install the rear planetary ring gear to the rear planetary ring gear flange sub-assembly.
Using a screwdriver, install the snap ring to the rear planetary ring gear flange sub-assembly with rear planetary ring gear.
Be careful not to damage the rear planetary ring gear flange sub-assembly with rear planetary ring gear.
Tape the screwdriver tip before use.
35077D 10.INSTALL REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY WITH REAR PLANETARY RING GEAR
| *1 | Thrust Bearing Race J (Front Race) | - | - |
Coat the thrust bearing race with ATF and install it to the rear planetary ring gear flange sub-assembly with rear planetary ring gear.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Bearing Race J (Front Race) |
33.4 (1.315) | 49.0 (1.929) |
Be sure to install the thrust bearing race in the correct direction.
Install the rear planetary ring gear flange sub-assembly with rear planetary ring gear to the automatic transmission case sub-assembly.
35797B 11.INSTALL ONE-WAY CLUTCH INNER RACE
| *1 | One-way Clutch Inner Race | *2 | No. 3 One-way Clutch Assembly |
Install the one-way clutch inner race to the No. 3 one-way clutch assembly.
Rotate the one-way clutch inner race clockwise to install it.
35770C 12.INSTALL NO. 3 ONE-WAY CLUTCH ASSEMBLY WITH ONE-WAY CLUTCH INNER RACE
| *1 | No. 3 One-way Clutch Assembly with One-way Clutch Inner Race | *2 | Snap Ring |
| *a | 19° | *b | 49° |
|
Front Side | - | - |
Install the No. 3 one-way clutch assembly with one-way clutch inner race to the automatic transmission case sub-assembly.
Using SST, install the snap ring to the automatic transmission case sub-assembly.
Install the snap ring so that the tapered side is facing out.
Be sure to install the snap ring so that the ends of the snap ring are within the area shown in the illustration.
35621V 14.INSTALL NO. 1 BRAKE PISTON
Coat 2 new O-rings with ATF and install them to the No. 1 brake piston.
With the No. 1 brake piston return spring sub-assembly installed to the No. 1 brake piston, align the 2 claws of the No. 1 brake piston return spring sub-assembly with the 2 claws of the No. 1 brake cylinder, and then install the No. 1 brake piston to the No. 1 brake cylinder.
35698 15.INSTALL NO. 1 BRAKE CYLINDER WITH NO. 1 BRAKE PISTON
Install the No. 1 brake cylinder with No. 1 brake piston to the automatic transmission case sub-assembly while making sure that the 2 claws of the No. 1 brake cylinder with No. 1 brake piston are positioned as shown in the illustration.
35608J 16.INSTALL NO. 1 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY
| *a | 22.5° | *b | 37.5° |
|
Turn | - | - |
Align the 2 claws of the No. 1 brake piston return spring sub-assembly with the 2 claws of the No. 1 brake cylinder, and then install the No. 1 brake piston return spring sub-assembly to the No. 1 brake piston.
Place SST on the No. 1 brake piston return spring sub-assembly, and compress the No. 1 brake piston return spring sub-assembly with a press.
Using a screwdriver, install the snap ring to the automatic transmission case sub-assembly.
Be sure to install the snap ring so that the ends of the snap ring are within the area shown in the illustration.
Be careful not to damage the automatic transmission case sub-assembly.
Tape the screwdriver tip before use.
35681A 17.INSTALL NO. 1 BRAKE DISC
| *1 | No. 1 Brake Flange | *2 | No. 1 Brake Disc |
| *3 | No. 1 Brake Plate | - | - |
| *a | 22.5° | *b | 37.5° |
Install the No. 1 brake flange, 4 No. 1 brake discs and 4 No. 1 brake plates to the automatic transmission case sub-assembly.
Make sure that the No. 1 brake discs, No. 1 brake plates and No. 1 brake flange are installed in the correct order.
Using a screwdriver, install the snap ring to the automatic transmission case sub-assembly.
Be sure to install the snap ring so that the ends of the snap ring are within the area shown in the illustration.
Be careful not to damage the automatic transmission case sub-assembly.
Tape the screwdriver tip before use.
35719B 19.INSTALL PLANETARY SUN GEAR
35750 20.INSTALL CENTER PLANETARY GEAR ASSEMBLY
| *1 | Thrust Bearing Race I | - | - |
Coat the thrust bearing race with ATF and install it to the center planetary gear assembly.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Bearing Race I | 53.7 (2.114) | 74.0 (2.913) |
Install the center planetary gear assembly to the automatic transmission case sub-assembly.
35763 21.INSTALL CENTER PLANETARY RING GEAR
| *1 | Center Planetary Ring Gear Flange | *2 | Center Planetary Ring Gear |
Install the center planetary ring gear flange to the center planetary ring gear.
Using a screwdriver, install the snap ring to the center planetary ring gear flange with center planetary ring gear.
Be careful not to damage the center planetary ring gear flange with center planetary ring gear.
Tape the screwdriver tip before use.
35769 22.INSTALL CENTER PLANETARY RING GEAR FLANGE WITH CENTER PLANETARY RING GEAR
| *1 | Thrust Needle Roller Bearing H | *2 | Thrust Needle Roller Bearing I |
Coat the 2 thrust needle roller bearings with ATF and install them to the center planetary ring gear flange with center planetary ring gear.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Needle Roller Bearing H | 63.3 (2.492) | 78.8 (3.102) |
| Thrust Needle Roller Bearing I | 55.7 (2.193) | 76.4 (3.008) |
Be sure to install the thrust needle roller bearing in the correct direction.
Install the center planetary ring gear flange with center planetary ring gear to the automatic transmission case sub-assembly.
35682A 23.INSTALL NO. 2 BRAKE DISC
| *1 | No. 2 Brake Flange | *2 | No. 2 Brake Disc |
| *3 | No. 2 Brake Plate | - | - |
Install the 2 No. 2 brake flanges, 5 No. 2 brake discs and 4 No. 2 brake plates to the automatic transmission case sub-assembly.
Make sure that the No. 2 brake discs, No. 2 brake plates and No. 2 brake flanges are installed in the correct order.
Install the thicker No. 2 brake flange first, and then install the thinner one.
35622G 24.INSTALL NO. 2 BRAKE PISTON
Coat 2 new O-rings with ATF and install them to the No. 2 brake piston.
With the No. 2 brake piston return spring sub-assembly installed to the No. 2 brake piston, align the claw of the No. 2 brake piston return spring sub-assembly with the claw of the No. 2 brake cylinder, and then install the No. 2 brake piston to the No. 2 brake cylinder.
Be careful not to damage the O-rings.
35699 25.INSTALL NO. 2 BRAKE CYLINDER WITH NO. 2 BRAKE PISTON
| *a | 30° | - | - |
|
Turn | - | - |
Install the No. 2 brake piston return spring sub-assembly to the automatic transmission case sub-assembly while making sure that the claw of the No. 2 brake piston return spring sub-assembly is positioned as shown in the illustration.
Install the No. 2 brake cylinder with No. 2 brake piston to the automatic transmission case sub-assembly while making sure that the claw of the No. 1 brake cylinder with No. 1 brake piston is positioned as shown in the illustration.
Place SST on the No. 2 brake cylinder, and compress the No. 2 brake piston return spring sub-assembly with a press.
Using a screwdriver, install the snap ring to the automatic transmission case sub-assembly.
Be sure to install the snap ring so that the ends of the snap ring are within the area shown in the illustration.
Be careful not to damage the automatic transmission case sub-assembly.
Tape the screwdriver tip before use.
35076C 27.INSTALL FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY
| *1 | Front Planetary Ring Gear | *2 | Snap Ring |
| *3 | Front Planetary Ring Gear Flange Sub-assembly | - | - |
Set the snap ring onto the front planetary ring gear flange sub-assembly. Using needle-nose pliers, insert the snap ring into the front planetary ring gear while squeezing it, and then expand the snap ring to install it.
Make sure the snap ring is securely inserted into the groove of the front planetary ring gear.
35743 28.INSTALL FRONT PLANETARY RING GEAR WITH FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY
| *1 | Thrust Needle Roller Bearing G | *2 | Thrust Bearing Race H |
Coat the thrust needle roller bearing and thrust bearing race with ATF and install them to the front planetary ring gear with front planetary ring gear flange sub-assembly.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Needle Roller Bearing G | 63.3 (2.492) | 78.8 (3.102) |
| Thrust Bearing Race H | 66.3 (2.610) | 78.9 (3.106) |
Be sure to install the thrust needle roller bearing and thrust bearing race in the correct direction.
Install the front planetary ring gear with front planetary ring gear flange sub-assembly to the automatic transmission case sub-assembly.
35720 29.INSTALL FRONT PLANETARY GEAR ASSEMBLY
| *1 | Thrust Bearing Race F | *2 | Thrust Bearing Race G |
Coat the 2 thrust bearing races with ATF and install them to the front planetary gear assembly.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Bearing Race F | 44.0 (1.732) | 62.8 (2.472) |
| Thrust Bearing Race G | 65.8 (2.591) | 86.3 (3.398) |
Be sure to install the thrust bearing race in the correct direction.
Install the front planetary gear assembly to the automatic transmission case sub-assembly.
35709J 30.INSTALL SUN GEAR INPUT DRUM SUB-ASSEMBLY
| *1 | Thrust Bearing Race E | *2 | Thrust Needle Roller Bearing F |
Coat the thrust needle roller bearing and thrust bearing race with ATF and install them to the sun gear input drum sub-assembly.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Bearing Race E | 40.83 (1.607) | 52.8 (2.079) |
| Thrust Needle Roller Bearing F | 37.1 (1.461) | 61.2 (2.409) |
Be sure to install the thrust needle roller bearing and thrust bearing race in the correct direction.
Install the sun gear input drum sub-assembly to the automatic transmission case sub-assembly.
35061 31.INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY
| *1 | Thrust Needle Roller Bearing D | *2 | Thrust Needle Roller Bearing E |
Coat the 2 thrust needle roller bearings with ATF and install them to the forward clutch hub sub-assembly.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Needle Roller Bearing D | 33.3 (1.311) | 56.6 (2.228) |
| Thrust Needle Roller Bearing E | 39.6 (1.559) | 52.8 (2.079) |
Be sure to install the thrust needle roller bearing in the correct direction.
Install the forward clutch hub sub-assembly to the automatic transmission case sub-assembly.
35631 32.INSTALL MULTIPLE DISC CLUTCH HUB
| *1 | Thrust Bearing Race C | *2 | Thrust Bearing Race D |
Coat the 2 thrust bearing races with ATF and install them to the multiple disc clutch hub.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Bearing Race C | 22.6 (0.889) | 44.8 (1.764) |
| Thrust Bearing Race D | 38.4 (1.512) | 56.5 (2.224) |
Be sure to install the thrust bearing race in the correct direction.
Install the multiple disc clutch hub to the automatic transmission case sub-assembly.
35652C 33.INSTALL DIRECT CLUTCH PISTON
| *1 | Direct Clutch Piston | *2 | Direct Clutch Drum Sub-assembly |
| *3 | O-ring | - | - |
Coat 2 new O-rings with ATF, and install them to the direct clutch piston.
Install the direct clutch piston to the direct clutch drum sub-assembly.
Be careful not to damage the O-rings.
35669 34.INSTALL NO. 2 CLUTCH BALANCER
| *1 | No. 2 Clutch Balancer | *2 | Direct Clutch Return Spring Sub-assembly |
| *3 | Direct Clutch Drum Sub-assembly | *4 | O-ring |
Install the direct clutch return spring sub-assembly to the direct clutch piston.
Coat a new O-ring with ATF, and install it to the No. 2 clutch balancer.
Install the No. 2 clutch balancer to the direct clutch drum sub-assembly.
Be careful not to damage the O-ring.
Place SST on the No. 2 clutch balancer, and compress the direct clutch return spring sub-assembly with a press.
Stop pressing when the spring sheet is lowered to the place 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.
Using SST, install the snap ring.
Do not expand the snap ring excessively.
35667A 35.INSTALL NO. 2 CLUTCH DISC (DIRECT CLUTCH DISC)
| *1 | Direct Clutch Flange | *2 | No. 2 Clutch Disc |
| *3 | No. 2 Clutch Plate | - | - |
Install the 5 No. 2 clutch plates, 5 No. 2 clutch discs and direct clutch flange to the direct clutch drum sub-assembly.
Make sure that the No. 2 clutch discs, No. 2 clutch plates and direct clutch flange are installed in the correct order.
Using a screwdriver, install the snap ring to the direct clutch drum sub-assembly.
Be careful not to damage the direct clutch drum sub-assembly.
Tape the screwdriver tip before use.
35612B 37.INSTALL FORWARD CLUTCH PISTON
| *1 | Forward Clutch Piston | *2 | Input Shaft Sub-assembly |
| *3 | O-ring | - | - |
Coat a new O-ring with ATF, and install it to the input shaft sub-assembly.
Coat a new O-ring with ATF, and install it to the forward clutch piston.
Install the forward clutch piston to the input shaft sub-assembly.
Be careful not to damage the O-rings.
35668 38.INSTALL NO. 1 CLUTCH BALANCER
| *1 | No. 1 Clutch Balancer | *2 | Forward Clutch Return Spring Sub-assembly |
| *3 | Input Shaft Sub-assembly | *4 | O-ring |
Coat a new O-ring with ATF, and install it to the No. 1 clutch balancer.
Install the forward clutch return spring sub-assembly and No. 1 clutch balancer to the input shaft sub-assembly.
Be careful not to damage the O-ring.
Place SST on the No. 1 clutch balancer, and compress the forward clutch return spring sub-assembly with a press.
Stop pressing when the spring sheet is lowered to the place 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.
Using SST, install the snap ring.
Do not expand the snap ring excessively.
35633B 39.INSTALL NO. 1 CLUTCH DISC (FORWARD CLUTCH DISC)
| *1 | Forward Clutch Flange | *2 | No. 1 Clutch Disc |
| *3 | No. 1 Clutch Plate | - | - |
Install the 5 No. 1 clutch plates, 5 No. 1 clutch discs and forward clutch flange to the input shaft sub-assembly.
Make sure that the No. 1 clutch discs, No. 1 clutch plates and forward clutch flange are installed in the correct order.
Using a screwdriver, install the snap ring.
Be careful not to damage the input shaft sub-assembly.
Tape the screwdriver tip before use.
35617 41.INSTALL CLUTCH DRUM OIL SEAL RING
| *1 | Clutch Drum Oil Seal Ring | *2 | Input Shaft Sub-assembly |
Coat 3 new clutch drum oil seal rings with ATF and install them to the input shaft sub-assembly.
Do not expand the clutch drum oil seal ring ends excessively.
After installing the clutch drum oil seal rings, check that they rotate smoothly.
35605A 42.INSTALL DIRECT CLUTCH DRUM SUB-ASSEMBLY
43.INSTALL DIRECT CLUTCH DRUM AND INPUT SHAFT ASSEMBLY
| *1 | Thrust Bearing Race B | *2 | Thrust Needle Roller Bearing B |
| *3 | Thrust Needle Roller Bearing C | - | - |
Coat the thrust bearing race and 2 thrust needle roller bearings with ATF and install them to the direct clutch drum and input shaft assembly.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Bearing Race B | 40.0 (1.575) | 52.8 (2.079) |
| Thrust Needle Roller Bearing B | 34.6 (1.362) | 52.0 (2.047) |
| Thrust Needle Roller Bearing C | 21.3 (0.839) | 41.1 (1.618) |
Be sure to install the thrust bearing race and thrust needle roller bearing in the correct direction.
Install the direct clutch drum and input shaft assembly to the automatic transmission case sub-assembly.
44.INSTALL OIL PUMP ASSEMBLY
| *1 | Thrust Needle Roller Bearing A | *2 | Thrust Bearing Race A |
| *3 | Oil Pump O-ring | *4 | Oil Pump Assembly |
Coat the thrust bearing race and thrust needle roller bearing with ATF and install them to the oil pump assembly.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Needle Roller Bearing A | 71.9 (2.831) | 85.6 (3.370) |
| Thrust Bearing Race A | 74.2 (2.921) | 87.74 (3.454) |
Be sure to install the thrust bearing race and thrust needle roller bearing in the correct direction.
Coat a new oil pump O-ring with ATF, and install it to the oil pump assembly.
Set the oil pump assembly on the input shaft, and align the bolt holes of the oil pump assembly with the automatic transmission case sub-assembly.
Be careful not to damage the oil pump O-ring.
Temporarily install the oil pump assembly to the automatic transmission case sub-assembly.
Install the oil pump assembly with the 10 bolts.
35506F 45.INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL
| *a | -0.5 to 0.5 mm (-0.0196 to 0.0196 in.) | - | - |
Using SST and a hammer, drive in 2 new manual valve lever shaft oil seals to the automatic transmission case sub-assembly.
-0.5 to 0.5 mm (-0.0196 to 0.0196 in.)
Coat the lip of the manual valve lever shaft oil seal with MP grease.
35505 46.INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY
| *1 | Manual Valve Lever Sub-assembly | *2 | Spacer |
Install a new spacer to the manual valve lever sub-assembly.
Install the manual valve lever shaft to the automatic transmission case sub-assembly through the manual valve lever sub-assembly.
Using a hammer, drive in a new spring pin.
Turn the spacer and manual valve lever shaft to align the smaller hole on the spacer with the indent on the manual valve lever sub-assembly.
Using a 3 mm pin punch and a hammer, stake the spacer.
Check that the spacer does not turn.
Make sure that the shaft rotates smoothly.
35556 47.INSTALL PARKING LOCK PAWL SHAFT
35501 48.INSTALL PARKING LOCK ROD SUB-ASSEMBLY
35595 49.INSTALL PARKING LOCK PAWL BRACKET
Install the parking lock pawl bracket to the automatic transmission case sub-assembly with the 3 bolts.
Move the manual valve lever sub-assembly to P, and check that the output shaft is locked by the parking lock pawl.
35159 50.INSTALL BRAKE DRUM GASKET
Coat 2 new brake drum gaskets with ATF and install them to the automatic transmission case sub-assembly.
35145C 51.INSTALL TRANSMISSION CASE GASKET
Coat 2 new transmission case gaskets with ATF and install them to the automatic transmission case sub-assembly.
35410 52.INSTALL TRANSMISSION VALVE BODY ASSEMBLY
| *1 | Manual Valve Lever Sub-assembly | *2 | Manual Valve |
|
Bolt A |
|
Bolt B |
|
Bolt C |
|
Bolt D |
Insert the manual valve lever sub-assembly into the groove on the end of the manual valve and install the transmission valve body assembly to the automatic transmission case sub-assembly with the 12 bolts.
Bolt length
Bolt A: 25 mm (0.984 in.)
Bolt B: 36 mm (1.42 in.)
Bolt C: 50 mm (1.97 in.)
Install the detent spring and detent spring cover to the transmission valve body assembly with the bolt.
Bolt length
Bolt D: 14 mm (0.551 in.)
35330 53.INSTALL VALVE BODY OIL STRAINER ASSEMBLY
Coat a new O-ring with ATF, and install it to the valve body oil strainer assembly.
Install the valve body oil strainer assembly to the transmission valve body assembly with the 3 bolts.
82125J 54.INSTALL TRANSMISSION WIRE
| *1 | Temperature Sensor Clamp | *2 | Temperature Sensor |
|
Bolt |
|
Connector |
|
O-ring | - | - |
Coat 2 new O-rings with ATF, and install them to the 2 temperature sensors.
Coat a new O-ring with ATF, and install it to the transmission wire.
Install the transmission wire to the automatic transmission case sub-assembly with the bolt.
Connect the 7 solenoid valve connectors.
Install the 2 temperature sensors and the 2 temperature sensor clamps to the transmission valve body assembly with the 2 bolts.
35394 55.INSTALL TRANSMISSION OIL CLEANER MAGNET
35106 56.INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY
| *1 | Sleeve | *2 | Automatic Transmission Case Sub-assembly |
| *a | Correct | *b | Incorrect |
| *c | Protrusion | - | - |
Install a new automatic transmission oil pan gasket to the automatic transmission oil pan sub-assembly.
Install the automatic transmission oil pan sub-assembly with automatic transmission oil pan gasket to the automatic transmission case sub-assembly with the 10 bolts.
Make sure that automatic transmission oil pan gasket seal surface and automatic transmission oil pan sub-assembly contact surface are free of oil and foreign matter.
Install the automatic transmission oil pan gasket so that there is no slack in the automatic transmission oil pan gasket, and the entire seal surface is level.
Make sure that the 8 protrusions are properly engaged to the automatic transmission oil pan sub-assembly.
When installing the automatic transmission oil pan sub-assembly, make sure that the automatic transmission oil pan gasket is not pinched between the sleeve and the seal surface of the automatic transmission case sub-assembly.
Install the drain plug and a new gasket to the automatic transmission oil pan sub-assembly.
Using a 5 mm hexagon socket wrench, install a new gasket and overflow plug to the automatic transmission oil pan sub-assembly.
35111 57.INSTALL AUTOMATIC TRANSMISSION HOUSING
|
Bolt A |
|
Bolt B |
|
Bolt C | - | - |
Install the automatic transmission housing to the automatic transmission case sub-assembly with the 8 bolts.
Apply adhesive to 2 or 3 threads on the end of the 4 bolts.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Install the 4 bolts to the automatic transmission housing.
35015F 58.INSTALL TRANSFER ADAPTER HOLE SNAP RING
Using snap ring pliers, install the transfer adapter hole snap ring to the transfer adapter sub-assembly.
36117A 59.INSTALL TRANSFER ADAPTER OIL SEAL
| *a | 0 to 0.5 mm (0 to 0.0196 in.) | - | - |
Using SST and a hammer, drive in a new transfer adapter oil seal to the transfer adapter sub-assembly.
0 to 0.5 mm (0 to 0.0196 in.)
Coat the lip of the transfer adapter oil seal with MP grease.
35015G 60.INSTALL REAR TRANSFER ADAPTER SUB-ASSEMBLY
| *a | 5.7 to 6.3 mm (0.225 to 0.248 in.) | *b | Seal Packing |
|
Straight Pin |
|
Bolt A |
|
Bolt B | - | - |
Using a plastic-faced hammer, tap 2 new straight pins into the transfer adapter sub-assembly.
5.7 to 6.3 mm (0.225 to 0.248 in.)
It is not necessary to remove the straight pins unless they are being replaced.
Clean and degrease the threads of the 10 bolts, bolt holes and the contact surfaces of the automatic transmission case sub-assembly and transfer adapter sub-assembly with non-residue solvent.
Apply seal packing to the transfer adapter sub-assembly as shown in the illustration.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
Apply seal packing in a continuous line (width 1.2 mm (0.0472 in.)) along the sealing surface.
Apply adhesive to 2 or 3 threads on the end of the 10 bolts.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Install the transfer adapter sub-assembly to the automatic transmission case sub-assembly with the 10 bolts.
| Bolt A | 40 mm (1.57 in.) |
| Bolt B | 50 mm (1.97 in.) |
61.INSTALL OIL COOLER TUBE UNION
| *a | Torque Wrench Fulcrum Length | *b | 18° to 22° |
| *c | -2° to 2° | - | - |
Coat 2 new O-rings with ATF and install them to the 2 oil cooler tube unions.
Using SST, install the 2 oil cooler tube unions to the automatic transmission case sub-assembly.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using SST (fulcrum length of 34.5 mm (1.3583 in.)) + torque wrench (fulcrum length of 180 mm (7.0866 in.)): 24.7 N*m (252 kgf*cm, 18 ft.*lbf)
35104A 62.INSTALL AUTOMATIC TRANSMISSION CASE PLUG
Coat a new O-ring with ATF, and install it to the automatic transmission case plug.
Using a T55 "TORX" socket wrench, install the automatic transmission case plug to the automatic transmission case sub-assembly.
Coat 6 new O-rings with ATF, and install them to the 6 automatic transmission case plugs.
Install the 6 automatic transmission case plugs to the automatic transmission case sub-assembly.
35015X 63.INSTALL REFILL PLUG
Install a new O-ring and the refill plug to the transfer adaptor sub-assembly.
84540 64.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY
|
|
| *a | Neutral Basic Line | *b | Groove |
Apply adhesive to threads of the bolt.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Temporarily install the park/neutral position switch assembly to the automatic transmission case sub-assembly with the bolt.
Tighten the bolt to the specified torque when adjusting the park/neutral position switch assembly.
Install the lock washer and nut to the park/neutral position switch assembly.
Temporarily install the transmission control shaft lever RH to the manual valve lever shaft with the spring washer and nut.
Align the neutral basic line with the groove as shown in the illustration, and tighten the bolt.
Turn the transmission control shaft lever RH clockwise until it stops, and then return the transmission control shaft lever RH counterclockwise 2 notches to N.
Using a screwdriver, bend the tabs of the lock washer.
Be careful not to damage the park/neutral position switch assembly.
Bend at least 2 of the lock washer tabs.
Tape the screwdriver tip before use.
35572 65.INSTALL TRANSMISSION CONTROL SHAFT LEVER RH
89413W 66.INSTALL TRANSMISSION REVOLUTION SENSOR (SP2)
Coat a new O-ring with ATF and install it to the transmission revolution sensor (SP2).
Be careful not to damage or twist the O-ring.
Install the transmission revolution sensor (SP2) with the bolt.
89413N 67.INSTALL TRANSMISSION REVOLUTION SENSOR (NT)
Coat a new O-ring with ATF and install it to the transmission revolution sensor (NT).
Be careful not to damage or twist the O-ring.
Install the transmission revolution sensor (NT) with the bolt.
68.INSTALL TRANSMISSION BREATHER HOSE ASSEMBLY
| *1 | No. 1 Breather Plug (ATM) | *2 | No. 2 Breather Plug (ATM) |
| *3 | Breather Plug Hose | *4 | O-ring |
Install the No. 1 breather plug (ATM) and No. 2 breather plug (ATM) to the breather plug hose.
Coat a new O-ring with ATF, and install it to the No. 2 breather plug (ATM).
Install the transmission breather hose assembly to the automatic transmission case sub-assembly.
Be careful not to damage the O-rings.