Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall)
RM38G0E _56 Audio / Visual / Telematics _100608 TELEMATICS _0467508 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B157111  Indicator (Green) Circuit Short to Ground  B157113  Indicator (Green) Circuit Open  


DESCRIPTION

This DTC is stored when the telephone transceiver assembly detects an open or short in the manual (SOS) switch indicator (green) circuit of the manual (SOS) switch.

The manual (SOS) switch indicator (green) illuminates after the ignition switch is turned to ON.

If the telematics system is not active, the manual (SOS) switch indicator (green) will turn off.

If the telematics system is active, the manual (SOS) switch indicator (green) will blink while communicating with the call center.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B157111 Indicator (Green) Circuit Short to Ground Manual (SOS) switch indicator (green) impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Telephone transceiver assembly

·

Map light assembly (manual [SOS] switch)

·

Harness or connector


Telematics A
B157113 Indicator (Green) Circuit Open Manual (SOS) switch indicator (green) impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Telephone transceiver assembly

·

Map light assembly (manual [SOS] switch)

·

Harness or connector


Telematics A

WIRING DIAGRAM

E354565E78
1.198,0.938 1.844,1.208 0.646,0.271 10 false GREEN 2.479,0.573 3.094,0.771 0.615,0.198 10 false IND2 2.448,1.156 3.063,1.354 0.615,0.198 10 false GND3 0.844,2.25 3.927,2.542 3.083,0.292 10 false Map Light Assembly 4.875,0.594 5.188,0.792 0.313,0.198 10 false 22 4.927,1.146 5.24,1.344 0.313,0.198 10 false 3 5.177,0.719 5.792,0.917 0.615,0.198 10 false IND2 5.177,1.167 5.792,1.365 0.615,0.198 10 false SIG- 4.948,2.042 5.406,2.24 0.458,0.198 10 false I55 4.927,2.219 6.333,2.594 1.406,0.375 10 false Telephone Transceiver Assembly 2.969,0.583 3.385,0.896 0.417,0.313 10 false 4 2.969,1.156 3.417,1.51 0.448,0.354 10 false 5 0.833,2.063 1.292,2.26 0.458,0.198 10 false d2 0.969,1.656 4.052,1.948 3.083,0.292 10 false Manual (SOS) Switch

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

Procedure1

c.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



Post-procedure1

d.

None



A

B

2.INSPECT MAP LIGHT ASSEMBLY (GREEN INDICATOR)
2.INSPECT MAP LIGHT ASSEMBLY (GREEN INDICATOR)

Pre-procedure1

a.
E462685C02
1.052,1.125 1.167,0.5 1.167,0.5 1.333,0.5 true 0.844,1.115 0.75,0.5 0.75,0.5 0.583,0.5 true 0.073,0.094 0.354,0.333 0.281,0.24 10 false *a 0.156,0.417 0.677,0.635 0.521,0.219 10 false GND3 1.396,0.417 1.833,0.625 0.438,0.208 10 false IND2
*a Component without harness connected
(Map Light Assembly [Manual (SOS) Switch])


Remove the map light assembly (manual [SOS] switch).

HINT:

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL



b.

Connect 2 dry-cell batteries (1.5 V each) in series.


c.

Connect a positive (+) lead from batteries to terminal 4 (IND2) and a negative (-) lead to terminal 5 (GND3) of the map light assembly (manual [SOS] switch) connector.


Procedure1

d.

Check if the manual (SOS) switch green indicator comes on.

OK:

Manual (SOS) switch green indicator illuminates.


Result:
Proceed to
OK
NG



Post-procedure1

e.

None



OK

3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

Pre-procedure1

a.

Disconnect the I55 telephone transceiver assembly connector.


b.

Disconnect the d2 map light assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I55,d2)Location & Routing

Click Connector(I55)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Telematics Transceiver Assembly

Click Connector(d2)Body>No. 1 Roof Wire>Map Light Assembly (Front)

I55-3 (SIG-) - d2-5 (GND3) Always Below 1 Ω
I55-22 (IND2) - d2-4 (IND2) Always Below 1 Ω
I55-3 (SIG-) - Body ground Always 10 kΩ or higher
I55-22 (IND2) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Result:
Proceed to
NEXT



NEXT