Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall)
RM38G0E _56 Audio / Visual / Telematics _100608 TELEMATICS _0467508 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B15C511  Emergency Call Switch Circuit Short to Ground  B15C513  Emergency Call Switch Circuit Open  


DESCRIPTION

If the telephone transceiver assembly detects an error in the communication between the telephone transceiver assembly and the map light assembly (manual [SOS] switch) as a result of the telephone transceiver assembly self check, this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B15C511 Emergency Call Switch Circuit Short to Ground Manual (SOS) switch impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Map light assembly

·

Harness or connector

·

Telephone transceiver assembly


Telematics A
B15C513 Emergency Call Switch Circuit Open Manual (SOS) switch impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Map light assembly

·

Harness or connector

·

Telephone transceiver assembly


Telematics A

WIRING DIAGRAM

E364512E82
0.375,3.156 2.865,3.344 2.49,0.188 10 false Telephone Transceiver Assembly 0.396,2.99 1.406,3.354 1.01,0.365 10 false I55 3.729,3.01 3.927,3.188 0.198,0.177 10 false d2 3.729,3.177 5.958,3.448 2.229,0.271 10 false Map Light Assembly 1.292,0.99 1.688,1.146 0.396,0.156 10 false SIG1 1.708,0.99 1.927,1.167 0.219,0.177 10 false 21 3.677,0.979 4.073,1.135 0.396,0.156 10 false SIG1 3.396,0.979 3.635,1.135 0.24,0.156 10 false 16 4.219,1.542 5.938,1.833 1.719,0.292 10 false Manual (SOS) Switch 3.677,2.302 4.073,2.458 0.396,0.156 10 false GND3 3.448,2.302 3.646,2.469 0.198,0.167 10 false 5 1.313,2.313 1.625,2.469 0.313,0.156 10 false SIG- 1.729,2.302 1.906,2.479 0.177,0.177 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC OUTPUT

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 10 seconds or more.


Procedure1

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Telematics > Trouble Codes
50001 459
Result:
Result Proceed to
No DTCs are output. A
DTCs are output. B



Post-procedure1

c.

None



A

B

2.INSPECT MAP LIGHT ASSEMBLY
2.INSPECT MAP LIGHT ASSEMBLY

Pre-procedure1

a.
E462685C03
1.333,0.417 1.167,0.417 1.167,0.417 0.875,1.125 true 1.25,1.917 1.083,1.917 1.083,1.917 0.865,1.396 true 1.313,1.833 1.792,2.031 0.479,0.198 10 false SIG1 1.396,0.333 1.896,0.531 0.5,0.198 10 false GND3 0.208,0.125 0.688,0.323 0.479,0.198 10 false *a
*a Component without harness connected
(Map Light Assembly)


Remove the map light assembly.

HINT:

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
16 (SIG1) - 5 (GND3) Manual (SOS) switch not operated 410 to 414 Ω
16 (SIG1) - 5 (GND3) Manual (SOS) switch operated 81 to 83 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

Pre-procedure1

a.

Disconnect the I55 telephone transceiver assembly connector.


b.

Disconnect the d2 map light assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I55,d2)Location & Routing

Click Connector(I55)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Telematics Transceiver Assembly

Click Connector(d2)Body>No. 1 Roof Wire>Map Light Assembly (Front)

I55-21 (SIG1) - d2-16 (SIG1) Always Below 1 Ω
I55-3 (SIG-) - d2-5 (GND3) Always Below 1 Ω
I55-21 (SIG1) - Body ground Always 10 kΩ or higher
I55-3 (SIG-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Result:
Proceed to
NEXT



NEXT