Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall)
RM38G0E _56 Audio / Visual / Telematics _100608 TELEMATICS _0467508 TELEMATICS SYSTEM(for eCall) J

TELEMATICS  TELEMATICS SYSTEM(for eCall)  Emergency Call Switch Illumination Circuit  


WIRING DIAGRAM

E465289E06
4.125,1.813 4.5,2.042 0.375,0.229 10 false d2 4.115,0.781 4.375,1 0.26,0.219 10 false 13 3.708,1.677 4.01,1.896 0.302,0.219 10 false 3 4.479,0.906 4.865,1.083 0.385,0.177 10 false IG 1.135,1.021 2.656,1.302 1.521,0.281 10 false from IGR-NO.2 Relay 4.479,1.688 4.948,1.865 0.469,0.177 10 false GND3 2.823,1.188 3.938,1.385 1.115,0.198 10 false ECU-IGR NO.2 4.125,1.021 4.5,1.25 0.375,0.229 10 false d1 4.969,2.177 6.479,2.406 1.51,0.229 10 false Manual (SOS) Switch 5.01,2.646 6.521,2.875 1.51,0.229 10 false Map Light Assembly 2.083,2.385 4.115,2.625 2.031,0.24 10 false Telephone Transceiver Assembly 2.083,2.208 2.542,2.406 0.458,0.198 10 false I55 4.167,1.583 4.469,1.802 0.302,0.219 10 false 5 3.281,1.813 3.75,1.99 0.469,0.177 10 false SIG-

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



HINT:

Inspect the fuses and relays related to this system before inspecting the suspected areas below.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY POWER SOURCE)
a.

Disconnect the d2 and d1 map light assembly connectors.


b.

Disconnect the I55 telephone transceiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(d2,I55)Location & Routing

Click Connector(d2)Body>No. 1 Roof Wire>Map Light Assembly (Front)

Click Connector(I55)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Telematics Transceiver Assembly

d2-5 (GND3) - I55-3 (SIG-) Always Below 1 Ω
d2-5 (GND3) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(d1)Location & Routing

Click Connector(d1)Body>No. 1 Roof Wire>Map Light Assembly (Front)

d1-13 (IG) -Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL [SOS] SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL [SOS] SWITCH)
a.
E462686C03
1.531,2.833 1.917,3.083 0.385,0.25 1.531,0.667 1.917,0.917 0.385,0.25 0.563,2.833 0.729,2.833 0.729,2.833 0.802,3.542 true 2.729,2.333 2.583,2.333 2.583,2.333 2.417,1.698 true 0.25,0.25 0.563,0.448 0.313,0.198 10 false *a 1.646,0.698 1.958,0.896 0.313,0.198 10 false d1 1.646,2.865 1.958,3.063 0.313,0.198 10 false d2 0.146,2.75 0.76,2.948 0.615,0.198 10 false GND3 2.813,2.25 3.125,2.448 0.313,0.198 10 false IG
*a Component without harness connected (Map Light Assembly [Manual (SOS) Switch])


Remove the map light assembly (manual [SOS] switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Connect 2 dry-cell batteries (1.5 V each) in series.


c.

Connect a positive (+) lead from batteries to terminal d1-13 (IG) and a negative (-) lead to terminal d2-5 (GND3) of the map light assembly (manual [SOS] switch) connector.


d.

Check if the manual (SOS) switch green indicator comes on.

OK:

Manual (SOS) switch green indicator illuminates.



Result:
Proceed to
OK
NG



OK

REPLACE MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR