Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM (w/ Variable Flow Control Solenoid Valve) › 2021.04–2021.07
RM38G0E _55 Steering _100915 POWER ASSIST SYSTEMS _0469466 POWER STEERING SYSTEM(w/ Variable Flow Control Solenoid Valve) J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(w/ Variable Flow Control Solenoid Valve)  Heavy Steering Feel (Power Steering Warning Light (Yellow))  


PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Chassis > Steering Actuator > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Battery Voltage Drop History Number of times vehicle battery voltage dropped Min.: 0
Max.: 255
- -
Engine Revolution Ready Signal Communication Failure History Vehicle speed input value sent via CAN (equal to value indicated on speedometer) Min.: 0
Max.: 255
- -
Steering Angle Sensor Signal Communication Failure History Number of times steering angle sensor signal was interrupted Min.: 0
Max.: 255
- -
Vehicle Speed Signal Invalid History Number of times steering angle sensor signal was interrupted Min.: 0
Max.: 255
- -
Overheat Prevention Control History Number of times assist limit performed due to estimated temperature of power steering ECU and motor coil Min.: 0
Max.: 255
- -
Power Supply Voltage Drop Control History Number of times assist limit performed due to battery voltage having dropped to 9 V or less Min.: 0
Max.: 255
- -
Power Supply Voltage Drop Restraint Control History Number of times assist limit performed due to battery voltage having dropped to 9.7 V or less Min.: 0
Max.: 255
- -
Engine Stall/READY OFF Control History Number of times assist limit performed due to engine stall Min.: 0
Max.: 255
- -
High Load Continuous Control Number of Times Number of times assist limit performed to prevent motor from overheating when overloaded due to steering wheel being turned to full lock position for an extended period of time, tire pressing against curbstone, etc. Min.: 0
Max.: 255
- -
Vehicle Speed Signal Fault Control History Number of times assist power set to a value suitable for high-speed driving when driving at high speeds due to an abnormal vehicle speed signal Min.: 0
Max.: 255
- -
Load Control History Number of times electric load limited to ensure stable vehicle power when power steering could not function appropriately or battery voltage was too low to ensure stable power steering Min.: 0
Min.: 0
- -
Chassis > Steering Actuator > Data List
Tester Display
Battery Voltage Drop History
Engine Revolution Ready Signal Communication Failure History
Steering Angle Sensor Signal Communication Failure History
Vehicle Speed Signal Invalid History
Overheat Prevention Control History
Power Supply Voltage Drop Control History
Power Supply Voltage Drop Restraint Control History
Engine Stall/READY OFF Control History
High Load Continuous Control Number of Times
Vehicle Speed Signal Fault Control History
Load Control History
50003 499 351,353,354,355,356,357,358,359,360,361,363
HINT:

If the battery is not sufficiently charged or the voltage decreases temporarily, the amount of power assist will be reduced and the power steering warning light will come on. In such cases, the amount of power assist returns to normal when the battery voltage recovers.


OK:

No control history



Result:
Proceed to
OK
NG



OK

NG

2.CHECK FOR VEHICLE CONTROL HISTORY (RoB) (POWER STEERING SYSTEM)
2.CHECK FOR VEHICLE CONTROL HISTORY (RoB) (POWER STEERING SYSTEM)
a.

Check for vehicle control history (RoB) and note any codes that are output.

Chassis > Steering Actuator > Utility
Tester Display
Vehicle Control History (RoB)
50005 499 55
i.

Record the vehicle control history (RoB).



Result:
Result Proceed to
Vehicle control history (RoB) is not output A
Vehicle control history (RoB) other than (X206D) are output B
Vehicle control history (RoB) (X206D) is output C



A

B

C

3.CHECK FOR VEHICLE CONTROL HISTORY (RoB) FREEZE FRAME DATA (POWER STEERING SYSTEM)
3.CHECK FOR VEHICLE CONTROL HISTORY (RoB) FREEZE FRAME DATA (POWER STEERING SYSTEM)
a.

Check for vehicle control history (RoB) freeze frame data and note any codes that are output.

Chassis > Steering Actuator > Utility
Tester Display
Vehicle Control History (RoB)
50005 499 55
i.

Record the vehicle control history (RoB).



Result:
Result Proceed to
Vehicle control history (RoB) is not output A
Vehicle control history (RoB) freeze frame data (Status of Vehicle Power (IGP PDC) is OFF) and (Status of Vehicle Power (IGR PDC) is OFF) are output B
Vehicle control history (RoB) freeze frame data (Status of Vehicle Power (IGP PDC) is OFF) and (Status of Vehicle Power (IGR PDC) is ON) are output C



A

B

GO TO PROBLEM SYMPTOMS TABLE (ENGINE STALLS)

C

4.CHECK VEHICLE CONTROL HISTORY (AIRBAG SYSTEM)
4.CHECK VEHICLE CONTROL HISTORY (AIRBAG SYSTEM)
a.

Check for vehicle control history freeze frame data and note any codes that are output.

Body Electrical > SRS Airbag > Utility
Tester Display
Vehicle Control History
50005 444 54
Record Data Item Chart
Tester Display Measurement Item Range Diagnostic Note
Vehicle Speed Vehicle speed at main driven wheels 0 to 200 km/h If the vehicle speed is 200 km/h or more, "200 km/h" is displayed.
Engine RPM Data Number of crankshaft revolutions in 1 minute 0 to 12800 rpm -
Shift Position Signal Shift lever position N/D/R/P/5/4/3/2/LO/B/SD/S-Mode/Undetermined -

i.

Record the vehicle control history.

HINT:

If the engine is stopped while the vehicle is stationary and the shift lever is not in P, the power steering warning light (yellow) illuminates and the message "Engine Stopped Steering Power Low" will be displayed on the multi-information display in the combination meter assembly, but this is caused by incorrect operation and is not a malfunction.




Result:
Result Proceed to
Vehicle control history (vehicle speed 0 km/h or more, engine speed 0 rpm and shift position not in P) is output A
Vehicle control history (vehicle speed 0 km/h or more, engine speed 0 rpm and shift position not in P) is not output B



A

INCORRECT OPERATION

If incorrect operation of the ignition switch causes unintended ignition switch off operation while the shift lever is not in P, the engine will stop thus causing power steering system shutdown and illumination of the power steering system warning light (yellow), but this is not a malfunction. (power steering system control during engine stall)


B