Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C050012  Left Front Wheel Speed Sensor Circuit Short to Battery  


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the No. 2 skid control ECU (brake actuator assembly). These signals are used for brake control.

Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.

Each speed sensor detects that magnetic change and sends a pulse signal to the No. 2 skid control ECU (brake actuator assembly).

HINT:

When the connectors between the speed sensor and No. 2 skid control ECU (brake actuator assembly) are connected, the following waveform is output.


C435284E02
3.74,0.792 4.417,0.417 4.417,0.417 4.583,0.417 true 4.667,0.333 5.74,0.531 1.073,0.198 10 false Speed Sensor 1.792,1.833 2.625,2.031 0.833,0.198 10 false Backward 4.729,1.833 5.563,2.031 0.833,0.198 10 false Forward 3,2.958 4.375,3.167 1.375,0.208 10 false Speed Sensor Rotor 6.656,4.646 7.135,4.854 0.479,0.208 10 false 14 mA 6.656,4.958 7.146,5.156 0.49,0.198 10 false 7 mA 1.667,5.823 2.313,6.031 0.646,0.208 10 false Backward 3,5.823 3.354,6.021 0.354,0.198 10 false Stop 3.938,5.802 4.5,6.01 0.563,0.208 10 false Forward 4.25,5.375 4.948,5.594 0.698,0.219 10 false Low speed 5.635,5.448 6.406,5.667 0.771,0.219 10 false High speed

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C050012 Left Front Wheel Speed Sensor Circuit Short to Battery The speed sensor short signal is ON continuously for 0.5 seconds or more.
·

Front speed sensor LH

·

Wire harness and connector

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)

WIRING DIAGRAM

C460010E01
5.75,1.01 6.25,1.177 0.5,0.167 10 false FL+ 1.625,1.146 2.063,1.313 0.438,0.167 10 false FL+ 1.646,1.813 2.083,2 0.438,0.188 10 false FL- 5.76,1.698 6.219,1.896 0.458,0.198 10 false FL- 5.125,2.875 5.625,3.073 0.5,0.198 10 false B20 5.125,3.063 7.052,3.552 1.927,0.49 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 5.469,1.01 5.802,1.26 0.333,0.25 10 false 22 5.458,1.688 5.771,2 0.313,0.313 10 false 21 2.01,1.688 2.396,1.958 0.385,0.271 10 false 5 2.01,1.021 2.365,1.292 0.354,0.271 10 false 1 0.75,2.417 2.417,2.667 1.667,0.25 10 false Front Speed Sensor LH 0.75,2.25 1.219,2.448 0.469,0.198 10 false B12

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the B12 front speed sensor LH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B12)Location & Routing

Click Connector(B12)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Front Speed Sensor Wire LH

B12-1 (FL+) - B12-5 (FL-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B12)Location & Routing

Click Connector(B12)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Front Speed Sensor Wire LH

B12-5 (FL-) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR LH - BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR LH - BRAKE ACTUATOR ASSEMBLY)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR