Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for LHD) › 2021.04–2021.07
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0467250 BRAKE ACTUATOR(for LHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C455212N02
0,2.813 2.208,4.906 2.208,2.094 6.594,0.229 6.844,0.229 false 3.51,0.75 3.51,1 true 0.552,4.104 0.552,4.521 false 2.958,3.958 3.208,3.958 false 5.438,0.833 6.135,1.604 6.135,1.604 6.302,1.604 true 3.417,1.083 3.417,0.75 3.417,0.75 4.219,0.75 true 3.604,0.75 3.604,1 true 3.708,0.75 3.708,1 true 0.99,1.719 1.49,1.719 1.49,1.719 1.938,0.99 true 1.615,1.094 1.26,1.708 true 2.771,2.177 2.938,2.177 2.938,2.177 3.229,2.26 true 4.094,3.281 4.479,3.771 4.479,3.771 4.646,3.771 true 2.948,0.375 3.167,0.208 3.167,0.208 3.333,0.208 true 6.615,0.604 6.865,0.604 false 6.063,0.042 6.531,0.583 0.469,0.542 18 false 1, 4 6.333,0.427 6.802,0.969 0.469,0.542 18 false 5 0.479,4.531 0.948,5.073 0.469,0.542 18 false 2 2.708,3.781 3.177,4.323 0.469,0.542 18 false 3 6.688,1.448 7.156,1.99 0.469,0.542 18 false 6 4.5,0.594 4.969,1.135 0.469,0.542 18 false 7 0.427,1.594 1.177,1.99 0.75,0.396 18 false 7, 8 3.719,0.073 4.188,0.615 0.469,0.542 18 false 9 2.333,2.021 2.802,2.563 0.469,0.542 18 false 10 3.604,0.115 4.073,0.656 0.469,0.542 10 false ● 4.896,3.625 5.365,4.167 0.469,0.542 18 false 11 5.323,1.896 5.792,2.438 0.469,0.542 10 false x 3 2.49,2.76 2.958,3.302 0.469,0.542 10 false x 2 0.031,2.865 0.5,3.406 0.469,0.542 12 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 ENGINE SIDE COVER LH 51474B - - -
3 UPPER ENGINE SIDE UNDER COVER PLATE LH 51478C - - -
4 PERFORM ACCUMULATOR PRESSURE ZERO DOWN - (Click here) - -
5 DRAIN BRAKE FLUID - - (Click here) -
6 ENGINE ROOM MAIN WIRE 82111 (Click here) - -
7 DISCONNECT BRAKE TUBE - (Click here) - -
8 REMOVE BRAKE TUBE - (Click here) - -
9 NO. 2 BRAKE TUBE CLAMP 47372 (Click here) - -
10 BRAKE ACTUATOR WITH BRACKET - (Click here) - -
11 NO. 3 BRAKE ACTUATOR BRACKET 44593 (Click here) - -

*A except 1GR-FE - -
● Non-reusable part - -

C455218N01
5.417,1.938 5.833,1.938 false 3.792,3.917 4.208,3.917 false 2.927,1 3.167,0.75 3.167,0.75 3.333,0.75 false 3.125,2.031 3.323,2.354 3.323,2.354 3.49,2.354 false 1.938,3 2.354,3 false 2.083,2.833 2.917,2.833 true 2.083,2.99 2.083,2.573 2.083,2.573 2.333,2.573 true 1.885,3.833 2.385,3.833 false 2.115,3.656 2.948,3.656 true 2.104,3.833 2.104,3.417 2.104,3.417 2.354,3.417 true 6.115,1.792 6.667,2.146 0.552,0.354 18 false 12 1.5,3.688 2.052,4.042 0.552,0.354 18 false 13 1.49,2.844 2.042,3.198 0.552,0.354 18 false 14 4.25,3.802 4.802,4.156 0.552,0.354 10 false *1 1.719,0.458 2.271,0.813 0.552,0.354 10 false x 3 3.396,0.667 3.948,1.021 0.552,0.354 10 false *2 3.542,2.271 4.094,2.625 0.552,0.354 10 false *3

Procedure Part Name Code
Z101186

Z101188

Z101187

12 BRAKE ACTUATOR ASSEMBLY 44510 (Click here) - -
13 NO. 1 BRAKE ACTUATOR CASE COLLAR 44521A (Click here) - -
14 BRAKE ACTUATOR BRACKET CUSHION 44547B (Click here) - -

*1 BRAKE ACTUATOR BRACKET ASSEMBLY *2 NO. 1 BRAKE ACTUATOR BRACKET
*3 NO. 2 BRAKE ACTUATOR BRACKET - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake actuator assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
No. 2 skid control ECU (brake actuator assembly) ECU configuration - (Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)
1.

Bleed air

2.

Perform "Calibration"


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

Electronically controlled brake system disabled or malfunctions


(Click here)
Operate the electric parking brake switch (electric parking brake switch assembly) Parking brake indicator light blinks when the ignition switch is first turned to ON (Click here)
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -




CAUTION / NOTICE / HINT

NOTICE:

While the battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the battery is connected.


PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click here(Click here)



Hide 51474B 2.REMOVE ENGINE SIDE COVER LH (except 1GR-FE)

Hide 51478C 3.REMOVE UPPER ENGINE SIDE UNDER COVER PLATE LH

a.
C457195


Hide 4.PERFORM ACCUMULATOR PRESSURE ZERO DOWN

a.
C441118N02
0.417,0.063 0.698,0.417 0.281,0.354 18 false i

i.

Using the GTS, perform the accumulator pressure zero down operation.

1. Select "Motor Deactivate" on the "ECB Utility" screen.

Chassis > Brake/EPB > Utility
Tester Display
ECB Utility
50005 435 3617

2. Perform "Motor Deactivate" according to the display on the GTS.

3. Select "ECB Deactivate" on the "ECB Utility" screen.

Chassis > Brake/EPB > Utility
Tester Display
ECB Utility
50005 435 3617

4. Perform "ECB Deactivate" according to the display on the GTS.

5. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

HINT:

A buzzer may sound due to low accumulator pressure. As this is not a malfunction, continue the procedure.


6. Check that the brake pedal is firm.

NOTICE:

If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down operation is not complete.


7. Disconnect the cable from the negative (-) battery terminal.


CAUTION:
B422343

·

Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





b.
C455214N01
0.375,0.083 0.656,0.438 0.281,0.354 18 false i

i.

When the accumulator pressure zero down could not be performed using the GTS.

NOTICE:

If DTCs are output, the accumulator pressure zero down operation may not be complete. In this case, perform the following procedure.


1. except 1GR-FE:

Remove the engine side cover LH.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL

2. With the ignition switch off, disconnect the brake master cylinder with pump assembly connector.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.


3. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

4. Check that the brake pedal is firm.

NOTICE:

If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down operation is not complete.


5. Disconnect the cable from the negative (-) battery terminal.


CAUTION:
B422343

·

Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





Hide 5.DRAIN BRAKE FLUID

Z101186

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.



Hide 82111 6.DISCONNECT ENGINE ROOM MAIN WIRE

a.
C455216C01
0.375,0.073 0.625,0.406 0.25,0.333 18 false i 3.844,0.073 4.094,0.406 0.25,0.333 18 false ii
V113147

Release the lock lever
V113148

Disconnect the connector


i.

Disconnect the brake booster pump with accumulator assembly connector.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



ii.

Release the lock lever and disconnect the engine room main wire connector from the brake actuator assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.




Hide 7.DISCONNECT BRAKE TUBE

Z101186

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tubes from the connecting parts.




a.
C455220C01
3.604,0.563 3.604,0.229 3.604,0.229 4.104,0.208 true 2.979,1.531 3.146,1.531 3.146,1.531 3.542,1.01 true 2.854,0.125 3.021,0.125 3.021,0.125 3.469,0.458 true 3.844,0.781 4.146,1.281 4.146,1.281 4.313,1.281 true 2.583,0.667 3.25,0.667 true 3.729,0.646 4.406,0.448 4.406,0.448 4.573,0.448 true 2.76,1.417 2.927,1.646 0.167,0.229 10 true *b 2.375,0.552 2.542,0.74 0.167,0.188 10 true *a 2.677,0.021 2.844,0.188 0.167,0.167 10 true *c 4.125,0.104 4.302,0.271 0.177,0.167 10 true *d 4.594,0.365 4.75,0.552 0.156,0.188 10 true *e 4.354,1.188 4.49,1.406 0.135,0.219 10 true *f 0.385,0.083 0.719,0.417 0.333,0.333 18 false i
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly *b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Disc Brake Cylinder Assembly RH *d To Front Disc Brake Cylinder Assembly LH
*e To Rear Disc Brake Cylinder Assembly RH *f To Rear Disc Brake Cylinder Assembly LH


i.

Use tags or make a memo to identify the places to reconnect the brake tubes.



b.
C455224N01
0.375,0.073 0.958,0.406 0.583,0.333 18 false i

i.

Using a union nut wrench, disconnect the 6 brake tubes from the brake actuator assembly.



Hide 8.REMOVE BRAKE TUBE

Z101186

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tubes from the connecting parts.




a.
C457221N01
0.385,0.094 0.667,0.448 0.281,0.354 18 false i 0.396,2.115 0.677,2.469 0.281,0.354 18 false ii

i.

Using a union nut wrench, disconnect the 2 brake tubes from the brake booster with master cylinder assembly.

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tubes from the connecting parts.




ii.

Disengage the clamp and separate the 2 brake tubes.

NOTICE:

Do not kink or damage the brake tubes.




Hide 47372 9.REMOVE NO. 2 BRAKE TUBE CLAMP

Z101186

NOTICE:

Do not kink or damage the brake tubes.



a.
C457165


Hide 10.REMOVE BRAKE ACTUATOR WITH BRACKET

Z101186

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tubes from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator with bracket by the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Remove the brake actuator with bracket while avoiding the brake tubes.



a.
C455228


Hide 44593 11.REMOVE NO. 3 BRAKE ACTUATOR BRACKET

Z101186

HINT:

Perform this procedure only when replacement of the No. 3 brake actuator bracket is necessary.



a.
C455230


Hide 44510 12.REMOVE BRAKE ACTUATOR ASSEMBLY

Z101186

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.




a.
C455232


Hide 44521A 13.REMOVE NO. 1 BRAKE ACTUATOR CASE COLLAR

Z101186

HINT:

Perform this procedure only when replacement of the No. 1 brake actuator case collars is necessary.



a.
C455233


Hide 44547B 14.REMOVE BRAKE ACTUATOR BRACKET CUSHION

Z101186

HINT:

Perform this procedure only when replacement of the brake actuator bracket cushions is necessary.



a.
C455235