Refer to DTC C050012.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C050012
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Note |
|---|---|---|---|---|---|
| C050023 | Left Front Wheel Speed Sensor Signal Stuck Low | Any of the following is detected:
·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 30 seconds or more.
·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.
·
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 30 seconds or more. |
·
Speed sensor installation
·
Wire harness and connector
·
Front speed sensor LH
·
Front speed sensor rotor LH (front axle hub sub-assembly LH) |
Brake/EPB | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | When the +BS terminal voltage is 17.4 V or less | ○ | ○ | ○ |
| Malfunction Status | At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors | ○ | - | - |
| At a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) | - | ○ | - | |
| At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) | - | - | ○ | |
| Detection Time | 30 seconds or more. | 1 second or more. | 30 seconds or more. | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
Refer to DTC C050012.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C050012
After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
| *a | Correct |
| *b | Incorrect |
Check the front speed sensor LH installation.
There is no clearance between the front speed sensor LH and front steering knuckle LH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front speed sensor LH.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL
Check the front speed sensor tip LH.
The front speed sensor tip LH is free of scratches, oil, and foreign matter.
If there is oil or foreign matter on the front speed sensor LH, clean the front speed sensor LH.
If the front speed sensor LH is damaged, replace the front speed sensor LH with a new one.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform a road test.
Check the front speed sensor LH output value.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0.0 km/h (0 mph) Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| FL Wheel Speed |
The output value changes in accordance with the vehicle speed.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.
Disconnect the B12 front speed sensor LH connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B12,B20)Location & Routingewd_type=routing;type=c,c;code=B12,B20 |
||
| B12-1 (FL+) - B20-22 (FL+) | Always | Below 1 Ω |
| B12-1 (FL+) or B20-22 (FL+) - Body ground | Always | 10 kΩ or higher |
| B12-5 (FL-) - B20-21 (FL-) | Always | Below 1 Ω |
| B12-5 (FL-) or B20-21 (FL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the component with the front speed sensor rotor LH.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL
Check the front speed sensor rotor LH.
The front speed sensor rotor LH is free of scratches, oil, and foreign matter.
If there is oil or foreign matter on the front speed sensor rotor LH, clean the front speed sensor rotor LH.
Do not use parts cleaner when cleaning the front speed sensor rotor LH.
If the front speed sensor rotor LH is damaged, replace the front speed sensor rotor LH with a new one.
The front speed sensor rotor LH is incorporated into the front axle hub sub-assembly LH.
If the front speed sensor rotor LH needs to be replaced, replace it together with the front axle hub sub-assembly LH.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The front speed sensor rotor LH is damaged.) | B |
| NG (There is foreign matter on the front speed sensor rotor LH.) | C |
A
B
C