Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C05262A  Steering Angle Sensor Module Signal Stuck In Range  


DESCRIPTION

The No. 2 skid control ECU (brake actuator assembly) receives signals from the steering sensor via CAN communication.

HINT:

When a malfunction occurs in the communication line to the steering sensor, U012687 is output.

If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C05262A Steering Angle Sensor Module Signal Stuck In Range Normal communication between the No. 2 skid control ECU (brake actuator assembly) and the steering sensor and abnormal steering sensor zero point.
·

Steering sensor

·

Wire harness and connector


Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)

WIRING DIAGRAM

C377599E49
0.802,0.635 1.417,0.833 0.615,0.198 10 false CANL 0.781,1.229 1.396,1.427 0.615,0.198 10 false CANH 0.896,1.75 1.51,1.948 0.615,0.198 10 false BAT 0.938,2.438 1.552,2.635 0.615,0.198 10 false IG1 0.885,3.313 1.5,3.51 0.615,0.198 10 false ESS 6.031,0.635 6.646,0.833 0.615,0.198 10 false CANL 6.031,1.229 6.646,1.427 0.615,0.198 10 false CANH 3.615,1.729 5.167,2.146 1.552,0.417 10 false from Battery 3.635,2.396 4.792,2.677 1.156,0.281 10 false from IG Circuit 2.063,1.917 3.198,2.167 1.135,0.25 10 false ECU-B NO. 4 1.948,2.573 3.104,2.823 1.156,0.25 10 false ECU-IGR NO. 3 0.292,4.052 0.906,4.25 0.615,0.198 10 false I51 0.292,4.24 2.469,4.563 2.177,0.323 10 false Steering Sensor 5.208,3.875 5.823,4.073 0.615,0.198 10 false B20 5.208,4.073 7.104,4.51 1.896,0.438 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 2.979,3.542 4.906,3.792 1.927,0.25 10 false : CAN Communication Line 1.281,3.177 1.469,3.417 0.188,0.24 10 false 6 1.281,2.292 1.469,2.531 0.188,0.24 10 false 9 1.281,1.635 1.469,1.875 0.188,0.24 10 false 4 1.281,1.052 1.469,1.292 0.188,0.24 10 false 3 1.281,0.458 1.469,0.698 0.188,0.24 10 false 8 5.781,0.458 5.969,0.698 0.188,0.24 10 false 43 5.781,1.042 5.969,1.281 0.188,0.24 10 false 27

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466
Chassis > Brake/EPB > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

2.RECONFIRM DTC
2.RECONFIRM DTC
a.

Turn the ignition switch to ON and check that no CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


b.

Start the engine.


c.

Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left.


d.

Check that no speed sensor and/or yaw rate sensor DTCs are output.

Chassis > Brake Booster > Trouble Codes
50001 466
Chassis > Brake/EPB > Trouble Codes
50001 435
HINT:
·

If a speed sensor, or the yaw rate sensor is malfunctioning, DTCs for the steering sensor may be stored even though the steering sensor is normal.

·

If speed sensor and yaw rate sensor DTCs are output simultaneously, repair these malfunctions and then inspect the steering sensor.



Result:
Result Proceed to
DTC C05262A is output. A
CAN communication system DTCs are output. B
Speed sensor and/or yaw rate sensor DTCs are output. C




A

3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

B

C

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the I51 steering sensor connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I51)Location & Routing

Click Connector(I51)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Spiral Cable Sub-Assembly

I51-9 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BAT TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BAT TERMINAL)
a.

Turn the ignition switch off.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I51)Location & Routing

Click Connector(I51)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Spiral Cable Sub-Assembly

I51-4 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I51)Location & Routing

Click Connector(I51)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Spiral Cable Sub-Assembly

I51-6 (ESS) - Body ground 1 minute or more after disconnecting the cable from the negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR