Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › STEERING ANGLE SENSOR
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0467254 STEERING ANGLE SENSOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  STEERING ANGLE SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C457204N04
6.521,0.229 6.854,0.229 false 2.313,2.615 2.313,2.844 2.313,2.844 2.729,2.844 false 3.792,1.448 4.292,1.448 false 6.448,2.198 6.698,2.198 false 6.74,2.042 7.073,2.458 0.333,0.417 18 false 2 3.052,2.708 3.385,3.042 0.333,0.333 18 false 3 3.583,1.344 3.917,1.594 0.333,0.25 10 false *1 6.281,0.073 6.615,0.49 0.333,0.417 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - - - -
3 STEERING SENSOR 89245B (Click here) - -

*1 SPIRAL CABLE SUB-ASSEMBLY - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during steering sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Steering sensor Update ECU security key Vehicle control history (RoB) are stored (Click here)
Steering sensor (Including removal and installation) Steering angle neutral point Panoramic view monitor system (Click here)
Parking assist monitor system (Click here)
Steering angle setting Panoramic view monitor system (Click here)
Parking assist monitor system (Click here)
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
ยท

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -




PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.

Click here(Click here)


NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click here(Click here)



Hide 2.REMOVE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Hide 89245B 3.REMOVE STEERING SENSOR

a.
C436426C03
3.938,1.198 3.333,1.719 3.333,1.719 3.948,0.708 true 2.833,1.313 2.635,0.76 true 5.01,0.938 4.417,0.938 true 0.646,0.188 0.927,0.542 0.281,0.354 18 false i 3.208,1.729 3.375,1.927 0.167,0.198 10 true *a 2.771,1.333 2.938,1.521 0.167,0.188 10 true *b 5.052,0.854 5.333,1.042 0.281,0.188 10 true *b
*a Guide *b Pin


i.

Disengage the 6 claws, 2 guides and 2 pins, and remove the steering sensor from the spiral cable sub-assembly.

NOTICE:

Do not damage the claws or pins of the spiral cable sub-assembly.