Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C05001F  Left Front Wheel Speed Sensor Circuit Intermittent  


DESCRIPTION

Refer to DTC C050012.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C050012

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C05001F Left Front Wheel Speed Sensor Circuit Intermittent Any of the following is detected:
·

When the +BS terminal voltage is 17.4 V or less, an open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Front speed sensor LH

·

Speed sensor installation

·

Front speed sensor rotor LH (front axle hub sub-assembly LH)


Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)

C05001F DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition When the +BS terminal voltage is 17.4 V or less ○ ○ ○
Malfunction Status An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more ○ - -
At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds - ○ -
At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation - - ○
Detection Time - - 15 seconds or more.
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE

·

After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.READ VALUE USING GTS (FL WHEEL SPEED AND MOMENTARY INTERRUPTION)
a.

While monitoring the values of the Data List, perform a road test and attempt to reproduce the problem symptoms based on the interview with the customer and the vehicle conditions stored as Freeze Frame Data when the DTC was stored.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Speed Open Momentary interruption of front speed sensor LH pulse input to ECU Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Chassis > Brake/EPB > Data List
Tester Display
FL Wheel Speed
FL Speed Open
50003 435 14,102
OK:

The values change in accordance with the operation of the vehicle and there is no intermittent operation.


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK FRONT SPEED SENSOR LH INSTALLATION
2.CHECK FRONT SPEED SENSOR LH INSTALLATION
a.
C168336C07
0.76,1.917 1.083,2.083 0.323,0.167 10 *a 2.417,1.917 2.74,2.083 0.323,0.167 10 *b
*a Correct
*b Incorrect


Turn the ignition switch off.


b.

Check the front speed sensor LH installation.

OK:

There is no clearance between the front speed sensor LH and front steering knuckle LH.

The installation bolt is tightened properly.



Result:
Proceed to
OK
NG



OK

3.CHECK FRONT SPEED SENSOR LH (CHECK FOR FOREIGN MATTER)

NG

INSTALL FRONT SPEED SENSOR LH CORRECTLY

3.CHECK FRONT SPEED SENSOR LH (CHECK FOR FOREIGN MATTER)
a.

Remove the front speed sensor LH, and confirm that there is no foreign matter, oil or grease on the front speed sensor tip LH.

OK:

The front speed sensor tip LH is free of oil and foreign matter.


HINT:

If foreign matter of 1 mm (0.03937 in.) x 1 mm (0.03937 in.) or more is adhered to the front speed sensor LH, this DTC may be stored.



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT SPEED SENSOR ROTOR LH (CHECK FOR FOREIGN MATTER)

NG

7.CLEAN FRONT SPEED SENSOR LH
4.CHECK FRONT SPEED SENSOR ROTOR LH (CHECK FOR FOREIGN MATTER)
a.

Confirm that there is no foreign matter, oil or grease on the front speed sensor rotor LH.

OK:

The front speed sensor rotor LH is free of oil and foreign matter.


HINT:
·

If foreign matter of 1 mm (0.03937 in.) x 1 mm (0.03937 in.) or more is adhered to the front speed sensor rotor LH, this DTC may be stored.

·

The front speed sensor rotor LH is incorporated into the front axle hub sub-assembly LH.

If the front speed sensor rotor LH needs to be replaced, replace it together with the front axle hub sub-assembly LH.




Result:
Proceed to
OK
NG



OK

REPLACE FRONT SPEED SENSOR LH AND COMPONENT WITH FRONT SPEED SENSOR ROTOR LH

NG

5.CLEAN FRONT SPEED SENSOR ROTOR LH
5.CLEAN FRONT SPEED SENSOR ROTOR LH
a.

Clean the front speed sensor rotor LH.

NOTICE:

Do not use parts cleaner when cleaning the front speed sensor rotor LH.



Result:
Proceed to
NEXT



NEXT

6.READ VALUE USING GTS (FL WHEEL SPEED AND MOMENTARY INTERRUPTION)
6.READ VALUE USING GTS (FL WHEEL SPEED AND MOMENTARY INTERRUPTION)
a.

While monitoring the values of the Data List, perform a road test and attempt to reproduce the problem symptoms based on the interview with the customer and the vehicle conditions stored as Freeze Frame Data when the DTC was stored.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Speed Open Momentary interruption of front speed sensor LH pulse input to ECU Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Chassis > Brake/EPB > Data List
Tester Display
FL Wheel Speed
FL Speed Open
50003 435 14,102
OK:

The values change in accordance with the operation of the vehicle and there is no intermittent operation.


NOTICE:

Perform the above inspection before removing the sensor and connector.


HINT:

The front speed sensor rotor LH is incorporated into the front axle hub sub-assembly LH.

If the front speed sensor rotor LH needs to be replaced, replace it together with the front axle hub sub-assembly LH.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE FRONT SPEED SENSOR LH AND COMPONENT WITH FRONT SPEED SENSOR ROTOR LH

7.CLEAN FRONT SPEED SENSOR LH
a.

Clean the front speed sensor LH.

NOTICE:

When cleaning the front speed sensor LH, make sure to clean the installation hole before installation.



Result:
Proceed to
NEXT



NEXT

8.READ VALUE USING GTS (FL WHEEL SPEED AND MOMENTARY INTERRUPTION)
8.READ VALUE USING GTS (FL WHEEL SPEED AND MOMENTARY INTERRUPTION)
a.

While monitoring the values of the Data List, perform a road test and attempt to reproduce the problem symptoms based on the interview with the customer and the vehicle conditions stored as Freeze Frame Data when the DTC was stored.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Speed Open Momentary interruption of front speed sensor LH pulse input to ECU Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
-
Chassis > Brake/EPB > Data List
Tester Display
FL Wheel Speed
FL Speed Open
50003 435 14,102
OK:

The values change in accordance with the operation of the vehicle and there is no intermittent operation.


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

END

NG

4.CHECK FRONT SPEED SENSOR ROTOR LH (CHECK FOR FOREIGN MATTER)