Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C12A512  Left Front Wheel ABS Hold Solenoid Control Circuit Short to Battery  C12A514  Left Front Wheel ABS Hold Solenoid Control Circuit Short to Ground or Open  C12A518  Left Front Wheel ABS Hold Solenoid Control Circuit Current Below Threshold  C12A519  Left Front Wheel ABS Hold Solenoid Control Circuit Current Above Threshold  C12A51D  Left Front Wheel ABS Hold Solenoid Control Circuit Current Out of Range  C12B012  Left Front Wheel ABS Release Solenoid Control Circuit Short to Battery  C12B014  Left Front Wheel ABS Release Solenoid Control Circuit Short to Ground or Open  


DESCRIPTION

The solenoid relay and solenoid valves are built into the brake actuator assembly.

The front solenoid valve LH controls the brake fluid pressure of the front wheel cylinder LH of the vehicle.

When these DTCs are stored, the fail-safe function operates and the solenoid relay is turned off to prevent the solenoid valves from operating.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C12A512 Left Front Wheel ABS Hold Solenoid Control Circuit Short to Battery An excessive current is detected in the solenoid for 0.05 seconds or more. No. 2 skid control ECU (brake actuator assembly) Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)
C12A514 Left Front Wheel ABS Hold Solenoid Control Circuit Short to Ground or Open Insufficient current is detected in the solenoid for 0.05 seconds or more. No. 2 skid control ECU (brake actuator assembly) Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)
C12A518 Left Front Wheel ABS Hold Solenoid Control Circuit Current Below Threshold An open is detected in the solenoid for 0.05 seconds or more. No. 2 skid control ECU (brake actuator assembly) Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)
C12A519 Left Front Wheel ABS Hold Solenoid Control Circuit Current Above Threshold Overcurrent is detected in the solenoid for 0.05 seconds or more. No. 2 skid control ECU (brake actuator assembly) Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)
C12A51D Left Front Wheel ABS Hold Solenoid Control Circuit Current Out of Range Current leakage is detected in the solenoid for 0.05 seconds or more. No. 2 skid control ECU (brake actuator assembly) Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)
C12B012 Left Front Wheel ABS Release Solenoid Control Circuit Short to Battery Any of the following is detected:
·

Overcurrent is detected in the solenoid for 0.05 seconds or more.

·

Overheat in the solenoid is detected for 0.05 seconds or more.

·

When the solenoid is OFF, a current leak in the solenoid circuit is detected for 0.05 seconds or more.


No. 2 skid control ECU (brake actuator assembly) Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)
C12B014 Left Front Wheel ABS Release Solenoid Control Circuit Short to Ground or Open Any of the following is detected:
·

When the solenoid is not being operated, an open in the solenoid circuit or short to ground is detected for 0.05 seconds or more.

·

When the solenoid is being operated, an open in the solenoid circuit is detected for 0.05 seconds or more.

·

An open in the solenoid ground circuit is detected for 0.05 seconds or more.


No. 2 skid control ECU (brake actuator assembly) Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)

C12B012 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition When the solenoid is OFF - - ○
Malfunction Status Overcurrent is detected in the solenoid ○ - -
Overheat in the solenoid is detected - ○ -
A current leak in the solenoid circuit is detected - - ○
Detection Time 0.05 seconds or more. 0.05 seconds or more. 0.05 seconds or more.
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


C12B014 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition When the solenoid is not being operated ○ ○ - -
When the solenoid is being operated - - ○ -
Malfunction Status An open in the solenoid circuit is detected ○ - ○ ○
A short to ground is detected - ○ - -
Detection Time 0.05 seconds or more. 0.05 seconds or more. 0.05 seconds or more. 0.05 seconds or more.
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.REPLACE BRAKE ACTUATOR ASSEMBLY

NEXT

END