Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C12E712  Right Rear Wheel ABS Hold Solenoid Control Circuit Short to Battery  C12E714  Right Rear Wheel ABS Hold Solenoid Control Circuit Short to Ground or Open  C12E718  Right Rear Wheel ABS Hold Solenoid Control Circuit Current Below Threshold  C12E719  Right Rear Wheel ABS Hold Solenoid Control Circuit Current Above Threshold  C12E71D  Right Rear Wheel ABS Hold Solenoid Control Circuit Current Out of Range  C12F212  Right Rear Wheel ABS Release Solenoid Control Circuit Short to Battery  C12F214  Right Rear Wheel ABS Release Solenoid Control Circuit Short to Ground or Open  


DESCRIPTION

The solenoid relay and solenoid valves are built into the brake actuator assembly.

The rear solenoid valve RH controls the brake fluid pressure of the rear wheel cylinder RH of the vehicle.

When these DTCs are stored, the fail-safe function operates and the solenoid relay is turned off to prevent the solenoid valves from operating.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C12E712 Right Rear Wheel ABS Hold Solenoid Control Circuit Short to Battery An excessive current is detected in the solenoid for 0.05 seconds or more. No. 2 skid control ECU (brake actuator assembly) Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)
C12E714 Right Rear Wheel ABS Hold Solenoid Control Circuit Short to Ground or Open Insufficient current is detected in the solenoid for 0.05 seconds or more. No. 2 skid control ECU (brake actuator assembly) Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)
C12E718 Right Rear Wheel ABS Hold Solenoid Control Circuit Current Below Threshold An open is detected in the solenoid for 0.05 seconds or more. No. 2 skid control ECU (brake actuator assembly) Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)
C12E719 Right Rear Wheel ABS Hold Solenoid Control Circuit Current Above Threshold Overcurrent is detected in the solenoid for 0.05 seconds or more. No. 2 skid control ECU (brake actuator assembly) Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)
C12E71D Right Rear Wheel ABS Hold Solenoid Control Circuit Current Out of Range Current leakage is detected in the solenoid for 0.05 seconds or more. No. 2 skid control ECU (brake actuator assembly) Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)
C12F212 Right Rear Wheel ABS Release Solenoid Control Circuit Short to Battery Any of the following is detected:
·

Overcurrent is detected in the solenoid for 0.05 seconds or more.

·

Overheat in the solenoid is detected for 0.05 seconds or more.

·

When the solenoid is OFF, a current leak in the solenoid circuit is detected for 0.05 seconds or more.


No. 2 skid control ECU (brake actuator assembly) Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)
C12F214 Right Rear Wheel ABS Release Solenoid Control Circuit Short to Ground or Open Any of the following is detected:
·

When solenoid is not being operated, an open in the solenoid circuit or short to ground is detected for 0.05 seconds or more.

·

When the solenoid is being operated, an open in the solenoid circuit is detected for 0.05 seconds or more.

·

An open in the solenoid ground circuit is detected for 0.05 seconds or more.


No. 2 skid control ECU (brake actuator assembly) Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)

C12F212 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition When the solenoid is OFF - - ○
Malfunction Status Overcurrent is detected in the solenoid ○ - -
Overheat in the solenoid is detected - ○ -
A current leak in the solenoid circuit is detected - - ○
Detection Time 0.05 seconds or more. 0.05 seconds or more. 0.05 seconds or more.
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


C12F214 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition When the solenoid is not being operated ○ ○ - -
When the solenoid is being operated - - ○ -
Malfunction Status An open in the solenoid circuit is detected ○ - ○ ○
A short to ground is detected - ○ - -
Detection Time 0.05 seconds or more. 0.05 seconds or more. 0.05 seconds or more. 0.05 seconds or more.
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.REPLACE BRAKE ACTUATOR ASSEMBLY

NEXT

END