Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  P05DB00  Brake Pedal Position Sensor "B"  P05E000  Brake Pedal Position Sensor "A"/"B"  


DESCRIPTION

Refer to DTC C110000.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C110000

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
P05DB00 Brake Pedal Position Sensor "B" The difference in the SKS1 and SKS2 brake pedal stroke sensor assembly is invalid for 0.2 seconds or more.
·

Wire harness and connector

·

Brake pedal stroke sensor assembly


Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)
P05E000 Brake Pedal Position Sensor "A"/"B" The difference in change between sensor output voltage 1 (SKS1) and sensor output voltage 2 (SKS2) is excessively large for 0.2 seconds or more.
·

Wire harness and connector

·

Brake pedal stroke sensor assembly


Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing or reinstalling the brake pedal stroke sensor assembly, perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.READ VALUE USING GTS (BRAKE PEDAL STROKE SENSOR ASSEMBLY)
a.

Mount a pedal effort gauge.


b.

Start the engine and depress the brake pedal once.

HINT:

Depress the brake pedal after start the engine to set the vehicle to linear mode (switching solenoid (SSA) on).



c.

Depress the brake pedal slowly and check the brake pedal stroke sensor assembly output voltages with respect to brake pedal depression force.

Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stroke Sensor Brake pedal stroke sensor 1 Min.: 0.0 V
Max.: 5.0 V
Brake pedal released: 0.6 to 1.4 V Reading increases when brake pedal is depressed
Chassis > Brake Booster > Data List
Tester Display
Stroke Sensor
50003 466 207
Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stroke Sensor2 Brake pedal stroke sensor 2 Min.: 0.0 V
Max.: 5.0 V
Brake pedal released: 3.6 to 4.4 V Reading decreases when brake pedal is depressed
Chassis > Brake/EPB > Data List
Tester Display
Stroke Sensor2
50003 435 208
HINT:

Perform this procedure in linear mode (switching solenoid (SSA) on).


Standard Voltage:
Brake Effort
[N (kgf, lbf)]
Stroke Sensor
[V]
Stroke Sensor2
[V]
50 (5.1, 11.2) 1.18 to 1.88 3.12 to 3.82
100 (10.2, 22.5) 1.36 to 2.06 2.94 to 3.64
150 (15.3, 33.7) 1.54 to 2.24 2.76 to 3.46



Result:
Result Proceed to
OK A
NG (brake pedal stroke sensor 1) B
NG (brake pedal stroke sensor 2) C



A

B

2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)

C

3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Disconnect the B15 brake pedal stroke sensor assembly connector.


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B19,B15)Location & Routing

Click Connector(B19)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Brake Booster Control ECU (Brake Booster Assembly)

Click Connector(B15)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Brake Pedal Stroke Sensor Assembly

B19-3 (SKS1) - B15-6 (SKS1) Always Below 1 Ω
B19-3 (SKS1) or B15-6 (SKS1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the B15 brake pedal stroke sensor assembly connector.


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B20,B15)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

Click Connector(B15)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Brake Pedal Stroke Sensor Assembly

B20-10 (SKS2) - B15-1 (SKS2) Always Below 1 Ω
B20-10 (SKS2) or B15-1 (SKS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR