Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C052C14  ABS Pump Motor Control Circuit Short to Ground or Open  C052C16  ABS Pump Motor Control Circuit Voltage Below Threshold  C052C17  ABS Pump Motor Control Circuit Voltage Above Threshold  C052C29  ABS Pump Motor Control Signal Invalid  C052C49  ABS Pump Motor Control Internal Electronic Failure  C052F14  ABS Pump Motor Supply Voltage Circuit Short to Ground or Open  


DESCRIPTION

The motor relay and motor fail-safe relay are built into the brake actuator assembly.

When the No. 2 skid control ECU (brake actuator assembly) operates ABS, TRC, VSC, or brake assist, etc., the motor relay turns ON and drives the pump motor built into the brake actuator assembly.

If any DTCs related to motor supply power are stored, fail-safe is performed and supply of power to the motor relay is cut by the motor fail-safe relay.

If the voltage supplied to the motor relay (BM terminal) is below the DTC detection threshold due to low voltage from the battery or DC/DC converter circuit, these DTCs may be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C052C14 ABS Pump Motor Control Circuit Short to Ground or Open When the voltage at terminal +BS is between 9.5 and 17.4 V and the motor is being driven at full power, an abnormal voltage is detected for 0.12 seconds or more.
·

Wire harness and connector

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)
C052C16 ABS Pump Motor Control Circuit Voltage Below Threshold When the voltage at terminal +BS is between 9.5 and 17.4 V and the motor is stopped, the detected motor voltage is excessively low for 2 seconds or more. No. 2 skid control ECU (brake actuator assembly) Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)
C052C17 ABS Pump Motor Control Circuit Voltage Above Threshold When the voltage at terminal +BS is between 9.5 and 17.4 V and the motor is stopped, the detected motor voltage is excessively high for 2 seconds or more. No. 2 skid control ECU (brake actuator assembly) Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)
C052C29 ABS Pump Motor Control Signal Invalid When the voltage at terminal +BS is between 9.5 and 17.4 V and the motor is being driven, the detected motor voltage is excessively high for 0.12 seconds or more. No. 2 skid control ECU (brake actuator assembly) Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)
C052C49 ABS Pump Motor Control Internal Electronic Failure Either of the following is detected:
·

When the voltage at terminal +BS is between 9.5 and 17.4 V, overcurrent is detected in the motor circuit for 0.05 seconds or more.

·

When the voltage at terminal +BS is between 9.5 and 17.4 V, an abnormal voltage is detected in the motor relay gate for 0.12 seconds or more.


·

Wire harness and connector

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)
C052F14 ABS Pump Motor Supply Voltage Circuit Short to Ground or Open When voltage at +BS terminal is 9.5 V or more, open in BM terminal continues for 1 second or more.
·

Wire harness and connector

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)

C052C49 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When the voltage at terminal +BS is between 9.5 and 17.4 V ○ ○
Malfunction Status Overcurrent is detected in the motor circuit ○ -
An abnormal voltage is detected in the motor relay gate - ○
Detection Time 0.05 seconds or more. 0.12 seconds or more.
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C322755E34
0.365,1.365 1.344,1.917 0.979,0.552 10 false from Battery 1.719,1.552 2.781,1.74 1.063,0.188 10 false ABS NO. 1 4.583,2.208 6.125,2.458 1.542,0.25 10 false No. 2 Skid Control ECU 4.688,3.281 6.615,3.604 1.927,0.323 10 false Motor Fail-safe Relay 4.938,1.271 5.854,1.51 0.917,0.24 10 false Motor Relay 5.094,4.438 6.01,4.677 0.917,0.24 10 false Pump Motor 4.49,5.031 6.438,5.354 1.948,0.323 10 false Brake Actuator Assembly 4.49,4.854 4.875,5.063 0.385,0.208 10 false B20 3.667,3.125 4.229,3.344 0.563,0.219 10 false GND2 3.677,1.49 4.24,1.708 0.563,0.219 10 false BM 3.396,1.25 3.625,1.469 0.229,0.219 10 false 46 3.406,2.854 3.635,3.073 0.229,0.219 10 false 30

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BM TERMINAL)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B20)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

B20-46 (BM) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B20)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

B20-30 (GND2) - Body ground 1 minute or more after disconnecting the cable from the negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC
a.

Reconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


b.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
HINT:
·

If a speed signal of 20 km/h (12 mph) or more is sent to the No. 2 skid control ECU (brake actuator assembly) with the ignition switch turned to ON and the stop light switch assembly off, the ECU performs self-diagnosis of the motor circuit.

·

If the normal system code is output (no DTCs are output), slightly jiggle the connectors, wire harness, and fuses of the No. 2 skid control ECU (brake actuator assembly).

·

If any DTCs are output while jiggling a connector or wire harness of the No. 2 skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.



Result:
Result Proceed to
C052C14, C052C16, C052C17, C052C49 and C052F14 are not output A
C052C14, C052C16, C052C17, C052C49 or C052F14 is output B




A

B