Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C13B951  SM Valve Learning Not Programmed  C13B954  SM Valve Learning Missing Calibration  


DESCRIPTION

The No. 2 skid control ECU (brake actuator assembly) stores the individual characteristics of each linear solenoid built into the brake actuator assembly. Based on the stored information, the No. 2 skid control ECU (brake actuator assembly) calibrates the individual differences and controls systems.

The No. 2 skid control ECU (brake actuator assembly) receives the shift position P signal from the ECM through the CAN communication system.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C13B951 SM Valve Learning Not Programmed The SM solenoid valve offset learning value is not stored.
·

If this DTC is not output after performing SM solenoid valve offset learning, there is no malfunction.

·

Brake fluid leaks

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)
HINT:

During Dealer Mode, related DTCs are cleared.


C13B954 SM Valve Learning Missing Calibration SM solenoid valve offset learning cannot be obtained
·

If this DTC is not output after performing SM solenoid valve offset learning, there is no malfunction.

·

Brake fluid leaks

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.CHECK DTC
a.

Check that no DTCs other than those related to incomplete learning are output.

Chassis > Brake Booster > Trouble Codes
50001 466
Chassis > Brake/EPB > Trouble Codes
50001 435
OK:

DTCs other than those related to incomplete learning are not output.



Result:
Proceed to
OK
NG



OK

2.CHECK FOR FLUID LEAK

NG

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.CHECK FOR FLUID LEAK
a.

Brake fluid leaks and air in brake line inspection.

i.

Check and take a note of the fluid level in the brake master cylinder reservoir assembly.


ii.

Repeatedly depress the brake pedal and confirm that the brake pedal feels normal (no air in thesystem, etc.).


iii.

Check if the brake fluid level in the brake master cylinder reservoir assembly has changed.


iv.

If the brake fluid level has decreased, check for leaks due to damaged brake lines or hoses,loose union nuts, damaged brake master cylinder sub-assembly seals, etc.



OK:

There are no fluid leaks.


Result:
Proceed to
OK
NG



OK

3.PERFORM AIR BLEEDING

NG

REPAIR OR REPLACE APPLICABLE PART

3.PERFORM AIR BLEEDING

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING

Result:
Proceed to
NEXT



NEXT

4.PERFORM SM SOLENOID VALVE OFFSET LEARNING
4.PERFORM SM SOLENOID VALVE OFFSET LEARNING
a.

Check that the conditions required for SM solenoid valve offset learning are met and perform SM solenoid valve offset learning.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY

NOTICE:

If DTC C13B954 is output, wait 3 minutes or more with the ignition switch turned off, then perform learning after turning the ignition switch to ON and clearing the DTCs.


Chassis > Brake/EPB > Utility
Tester Display
Calibration
50005 435 5554
1.

The battery voltage is 11 to 14 V when the ignition switch is ON.

2.

The brake actuator assembly is not hot.

3.

The engine control system is not malfunctioning.

4.

The shift state indicator shows that the shift lever is in P.

5.

The brake pedal is not depressed.

6.

The parking brake is released.

7.

DTC C134551 is not output.



Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
C13B951 and C13B954 are not output A
C13B951 or C13B954 are output B



A

B