Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › ENGINE UNIT
RM38G0E _51 Engine / Hybrid System _101207 1GR-FE ENGINE MECHANICAL _0469488 ENGINE UNIT G

1GR-FE ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 11101A 1.INSPECT CYLINDER HEAD SET BOLT

A224657C09
1.677,1.292 1.875,1.531 0.198,0.24 10 false *a
*a Measurement Length


a.

Using a vernier caliper, measure the length of the cylinder head set bolt from the seat to the end.

Standard length:

141.3 to 142.7 mm (5.56 to 5.62 in.)


Maximum length:

143.7 mm (5.66 in.)


If the length is more than the maximum, replace the cylinder head set bolt.


b.
A226002

Using a vernier caliper, measure the diameter of the elongated thread at the narrowest visible area.

Standard diameter:

10.73 to 10.97 mm (0.422 to 0.432 in.)


Minimum diameter:

10.40 mm (0.409 in.)


If the diameter is less than the minimum, replace the cylinder head set bolt.

HINT:

If a visual check reveals no excessively thin areas, check the center of the bolt (refer to illustration) and find the area that has the smallest diameter.



Hide 13801 2.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Turn the roller by hand to check that it turns smoothly.

If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.


Hide 13750 3.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the valve lash adjuster assembly free of dirt and foreign objects.

·

Only use clean engine oil.



a.

Place the valve lash adjuster assembly into a container filled with engine oil.


b.

Insert the tip of SST into the valve lash adjuster assembly plunger and use the tip to press down on the check ball inside the plunger.

A385862C01
1.344,1.219 1.719,1.219 false 2.167,1.208 2.542,1.208 false 1.281,1.823 1.51,1.563 1.51,1.563 1.74,1.563 false 2.583,1.719 2.375,1.552 2.375,1.552 2.146,1.552 false 1.281,2.021 1.656,2.021 false 2.188,2.021 2.563,2.021 false 1.156,2.49 1.708,2.49 false 2.198,2.49 2.677,2.49 false 1.052,2.833 1.448,3.208 1.448,3.208 1.698,3.208 false 2.792,2.823 2.51,3.188 2.51,3.188 2.281,3.188 false 1,3.323 1,3.021 false 2.802,3.333 2.802,3.031 false 5.49,0.802 5.24,0.802 5.24,0.802 5.24,1.646 false 0.865,0.479 1.177,0.677 0.313,0.198 10 false *a 2.74,0.438 3.052,0.635 0.313,0.198 10 false *b 1.854,1.135 2.24,1.344 0.385,0.208 10 false SST 1.875,1.479 2.125,1.677 0.25,0.198 10 false *c 1.865,1.938 2.115,2.135 0.25,0.198 10 false *1 1.854,2.385 2.104,2.583 0.25,0.198 10 false *2 1.906,3.115 2.156,3.313 0.25,0.198 10 false *3 0.938,3.375 1.188,3.573 0.25,0.198 10 false *4 2.729,3.385 2.979,3.583 0.25,0.198 10 false *4 5.563,0.719 5.948,0.927 0.385,0.208 10 false SST
*1 Plunger *2 Low Pressure Chamber
*3 Check Ball *4 High Pressure Chamber
*a CORRECT *b INCORRECT
*c Tapered Path - -


SST
09276-75010  


c.

Squeeze SST and the valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed the air.

OK:

Plunger moves up and down.


NOTICE:

When bleeding air from the high-pressure chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.



e.

After bleeding the air, remove SST. Then try to quickly and firmly press the plunger by hand.

OK:

Plunger is very difficult to move.


If the result is not as specified, replace the valve lash adjuster assembly.


Hide 13511 4.INSPECT CAMSHAFT

a.

Inspect the camshaft runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum runout:

0.04 mm (0.00157 in.)


If the runout is more than the maximum, replace the camshaft.

HINT:

Check the oil clearance after replacing the camshaft.




b.

Using a micrometer, measure the cam lobe height.

Standard Cam Lobe Height:
Item Specified Condition
Intake 43.890 to 43.990 mm (1.728 to 1.732 in.)
Exhaust 44.262 to 44.362 mm (1.743 to 1.747 in.)


Minimum Cam Lobe Height:
Item Specified Condition
Intake 43.840 mm (1.726 in.)
Exhaust 44.212 mm (1.741 in.)



c.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 journal 35.946 to 35.960 mm (1.4152 to 1.4157 in.)
Other journals 25.959 to 25.975 mm (1.0221 to 1.0226 in.)


If the journal diameter is not as specified, check the oil clearance.


Hide 13050 5.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.

Fix the camshaft in place.

NOTICE:

Be careful not to damage the camshaft.



b.
A229667C12
2.219,1.73 2.401,1.909 0.182,0.179 10 *2 1.631,0.296 1.816,0.470 0.185,0.175 10 *1 2.204,1.812 2.092,1.812 2.092,1.812 1.89,1.443 false 1.613,0.387 1.383,0.387 1.383,0.387 0.91,1.212 false
*1 Pin Hole
*2 Straight Pin


Put the camshaft timing gear assembly and camshaft together by aligning the pin hole and straight pin.


c.

Lightly press and turn the camshaft timing gear assembly against the camshaft, and press harder after the pin enters the hole.

NOTICE:

Be sure not to turn the camshaft timing gear assembly in the retard direction.



d.

Check that there is no clearance between the camshaft timing gear assembly flange and camshaft.


e.
A229666

Tighten the flange bolt while holding the camshaft.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


f.

Check the lock of the camshaft timing gear assembly.

i.

Fix the camshaft in place and confirm that the camshaft timing gear assembly is locked.

NOTICE:

Be careful not to damage the camshaft.




g.
A229672C04
1.313,3.323 0.75,3.323 false 0.667,3.844 0.792,3.844 0.792,3.844 1.313,3.49 false 2.615,3.26 2.479,3.26 2.479,3.26 2.156,3.115 false 2.177,3.698 2.667,3.698 false 1.885,1.469 0.885,1.313 0.885,1.313 1.573,1.563 false 1.594,1.635 2.354,2.219 2.354,2.219 1.917,1.698 false 2.385,2.167 2.573,2.375 0.188,0.208 10 false *b 0.688,1.219 0.844,1.417 0.156,0.198 10 false *a 2.688,3.615 2.865,3.813 0.177,0.198 10 false *d 0.594,3.25 0.771,3.438 0.177,0.188 10 false *d 0.5,3.76 0.677,3.958 0.177,0.198 10 false *c 2.625,3.167 2.802,3.365 0.177,0.198 10 false *c
*a Advance Side Path
*b Retard Side Path
*c Open
*d Close
V100144

Rubber
V100145

Vinyl Tape


Release the lock pin.

i.

Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

HINT:

The 2 advance side paths are located in the camshaft groove. Plug one of the paths with a rubber piece.



ii.

Break through the tape on the advance side path and the retard side path on the opposite side of the hole of the advance side path as shown in the illustration.


iii.
A229673C03
2.5,0.229 2.271,0.229 2.271,0.229 1.854,1.302 false 1.594,1.188 1.208,0.198 1.208,0.198 1.042,0.198 false 2.521,0.135 2.688,0.323 0.167,0.188 10 false *b 0.885,0.104 1.052,0.292 0.167,0.188 10 false *a
*a Advance Side Path
*b Retard Side Path


Apply air at approximately 200 kPa (2.0 kgf/cm2, 28 psi) to the 2 open paths.

CAUTION:

Cover the paths with a piece of cloth when applying pressure to prevent oil from spraying.



iv.
A229674C04
2.594,0.656 2.323,0.656 2.323,0.656 1.833,1.375 false 0.802,0.615 1.042,0.615 1.042,0.615 1.594,1.271 false 2.625,0.563 2.792,0.75 0.167,0.188 10 false *b 0.615,0.531 0.781,0.729 0.167,0.198 10 false *a 2.354,1.656 2.531,1.854 0.177,0.198 10 false *d 0.875,1.594 1.073,1.792 0.198,0.198 10 false *c
*a Advance Side Path
*b Retard Side Path
*c Hold Pressure
*d Decompress


Check that the camshaft timing gear assembly rotates in the advance direction when reducing the air pressure applied to the retard side path.

HINT:

This operation releases the lock pin at the most retarded position.



v.

When the camshaft timing gear assembly reaches the most advanced position, release the air pressure first from the retard side path and next from the advance side path.

NOTICE:

Do not release the air pressure from the advance side path first. The gear may abruptly shift in the retard direction and break the lock pin.




h.

Check for smooth rotation.

i.

Turn the camshaft timing gear assembly within its movable range (21°) 2 or 3 times, but do not turn it to the most retarded position. Make sure that the gear turns smoothly.

NOTICE:

Do not use air pressure to perform the smooth operation check.




i.

Check the lock in the most retarded position.

i.

Confirm that the camshaft timing gear assembly locks at the most retarded position.



j.
A227959C07
2.063,0.823 2.448,0.094 2.448,0.094 2.552,0.094 false 0.656,1.896 0.51,1.896 0.51,1.896 0.333,1.615 false 0.979,0.854 0.729,0.208 0.729,0.208 0.563,0.208 false 1.385,1.063 1.938,1.844 false 1.26,1.521 1.5,1.844 1.5,1.844 2.083,1.844 false 0.385,0.115 0.573,0.292 0.188,0.177 10 false *a 2.104,1.75 2.323,1.948 0.219,0.198 10 false *a 2.563,0 2.76,0.177 0.198,0.177 10 false *2 0.677,1.802 0.875,1.99 0.198,0.188 10 false *1
*1 Flange Bolt
*2 Straight Pin
*a Do not remove


Remove the flange bolt and camshaft timing gear assembly.

NOTICE:
·

Do not remove the other 3 bolts.

·

If planning to reuse the camshaft timing gear, be sure to release the straight pin lock before installing the camshaft timing gear.




Hide 13070A 6.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.

Fix the camshaft in place.

NOTICE:

Be careful not to damage the camshaft.



b.
A227956C11
1.911,0.121 2.094,0.300 0.182,0.179 10 *2 0.441,0.099 0.626,0.273 0.185,0.175 10 *1 1.08,0.918 0.771,0.188 0.771,0.188 0.64,0.188 false 1.308,0.922 1.727,0.212 1.727,0.212 1.879,0.212 false
*1 Pin Hole
*2 Straight Pin


Put the camshaft timing exhaust gear assembly and camshaft together by aligning the pin hole and straight pin.


c.

Lightly press and turn the camshaft timing exhaust gear assembly against the camshaft, and press harder after the pin enters the hole.

NOTICE:

Be sure not to turn the camshaft timing exhaust gear in the advanced direction.



d.

Check that there is no clearance between the camshaft timing exhaust gear flange and camshaft.


e.
A229668

Tighten the flange bolt while holding the camshaft.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


f.

Check the camshaft timing exhaust gear.

i.

Fix the camshaft in place and confirm that the camshaft timing exhaust gear assembly is locked.

NOTICE:

Be careful not to damage the camshaft.




g.
A229675C03
0.677,3.927 0.813,3.927 0.813,3.927 1.333,3.677 false 0.74,3.188 0.938,3.188 0.938,3.188 1.344,3.073 false 2.625,3.198 2.51,3.198 2.51,3.198 2.188,3.302 false 2.688,3.698 2.521,3.698 2.521,3.698 2.167,3.469 false 1.917,1.604 2.354,1.833 2.354,1.833 1.604,1.698 false 1.583,1.469 1.125,1.5 1.125,1.5 1.896,1.542 false 0.927,1.438 1.115,1.635 0.188,0.198 10 false *b 2.406,1.719 2.563,1.917 0.156,0.198 10 false *a 2.646,3.125 2.833,3.333 0.188,0.208 10 false *d 0.5,3.854 0.677,4.063 0.177,0.208 10 false *d 0.583,3.115 0.76,3.333 0.177,0.219 10 false *c 2.708,3.604 2.875,3.802 0.167,0.198 10 false *c
*a Advance Side Path
*b Retard Side Path
*c Open
*d Close
V100144

Rubber
V100145

Vinyl Tape


Release the lock pin.

i.

Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

HINT:

The 2 advance side paths are located in the camshaft groove. Plug one of the paths with a rubber piece.



ii.

Break through the tape on the advance side path and the retard side path on the opposite side of the hole of the advance side path as shown in the illustration.


iii.
A229676C03
0.885,0.583 1.115,0.583 1.115,0.583 1.583,1.26 false 2.469,0.635 2.302,0.635 2.302,0.635 1.865,1.125 false 0.719,0.5 0.906,0.688 0.188,0.188 10 false *a 2.49,0.542 2.667,0.708 0.177,0.167 10 false *b
*a Advance Side Path
*b Retard Side Path


Apply air at approximately 200 kPa (2.0 kgf/cm2, 28 psi) to the 2 open paths (the advance side path and retard side path).

CAUTION:

Cover the paths with a piece of cloth when applying pressure to prevent oil from spraying.



iv.
A229677C04
2.51,0.5 2.365,0.5 2.365,0.5 1.854,1.26 false 0.865,0.563 1.031,0.563 1.031,0.563 1.594,1.375 false 2.542,0.406 2.729,0.573 0.188,0.167 10 false *b 0.698,0.479 0.875,0.646 0.177,0.167 10 false *a 2.385,1.604 2.583,1.771 0.198,0.167 10 false *c 0.906,1.708 1.083,1.875 0.177,0.167 10 false *d
*a Advance Side Path
*b Retard Side Path
*c Hold Pressure
*d Decompress


Make sure that the camshaft timing exhaust gear assembly rotates in the retard direction when reducing the air pressure applied to the advance side path.

HINT:

The lock pin is released and the camshaft timing exhaust gear assembly turns in the retard direction.



v.

When the camshaft timing exhaust gear assembly moves to the most retarded position, release the air pressure first from the advance side path, and then release the air pressure from the retard side path.

NOTICE:

Be sure to release the air pressure from the advance side path first. If the air pressure of the retard side path is released first, the camshaft timing exhaust gear assembly may abruptly shift in the advance direction and break the lock pin or other parts.




h.

Check for smooth rotation.

i.

Turn the camshaft timing exhaust gear assembly within its movable range (18.5°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the gear assembly turns smoothly.

NOTICE:

When the air pressure is released from the advance side path and then from the retard side path, the gear assembly automatically returns to the most advanced position due to the advance assist spring operation and locks. Gradually release the air pressure from the retard side path before performing the smooth rotation check.




i.

Check the lock at the most advanced position.

i.

Make sure that the camshaft timing exhaust gear assembly locks at the most advanced position.



j.
A227960C11
0.323,1.635 0.479,1.854 0.479,1.854 0.615,1.854 false 0.396,0.521 0.656,0.521 0.656,0.521 0.927,0.823 false 0.854,1.146 0.656,0.521 false 1.229,1.615 1.365,1.802 1.365,1.802 1.844,1.802 false 1.313,1.25 1.74,1.802 false 2.01,0.781 2.25,0.156 2.25,0.156 2.385,0.156 false 2.427,0.073 2.615,0.26 0.188,0.188 10 false *2 0.646,1.771 0.844,1.948 0.198,0.177 10 false *1 0.229,0.427 0.406,0.615 0.177,0.188 10 false *a 1.885,1.698 2.063,1.885 0.177,0.188 10 false *a
*1 Flange Bolt
*2 Straight Pin
*a Do not remove


Remove the flange bolt and camshaft timing exhaust gear assembly.

NOTICE:
·

Be sure not to remove the other 4 bolts.

·

If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.




Hide 13506 7.INSPECT CHAIN SUB-ASSEMBLY

a.
A139523C18
2.875,1.76 3.094,1.917 0.219,0.156 10 false 16 0.688,1.76 0.833,1.927 0.146,0.167 10 false 1 0.844,1.76 0.979,1.906 0.135,0.146 10 false 2 1.01,1.76 1.146,1.906 0.135,0.146 10 false 3 1.177,1.76 1.313,1.906 0.135,0.146 10 false 4 1.365,1.76 1.5,1.906 0.135,0.146 10 false 5 1.542,1.76 1.677,1.906 0.135,0.146 10 false 6 1.698,1.104 1.906,1.292 0.208,0.188 10 false *a
*a Measurement Area


Using a spring scale, pull the chain with a force of 147 N (15 kgf, 33 lbf) and measure the length of the chain using a vernier caliper.

Maximum chain elongation:

136.9 mm (5.39 in.)


HINT:

Perform the measurement at 3 random places.


If a measurement is more than the maximum, replace the chain sub-assembly.


Hide 13507 8.INSPECT NO. 2 CHAIN SUB-ASSEMBLY

a.

Using a spring scale, pull the No. 2 chain sub-assembly with a force of 147 N (15 kgf, 33 lbf) and measure the length of the No. 2 chain using a vernier caliper.

Maximum chain elongation:

137.6 mm (5.42 in.)


HINT:

Perform the measurement at 3 random places.


If a measurement is more than the maximum, replace the No. 2 chain sub-assembly.


Hide 13521 9.INSPECT CRANKSHAFT TIMING SPROCKET

a.
A131945

Wrap the chain around the sprocket.


b.

Using a vernier caliper, measure the crankshaft timing sprocket diameter with the chain.

Minimum gear diameter (with chain):

61.0 mm (2.40 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the chain and crankshaft timing sprocket.


Hide 10.INSPECT NO. 1 IDLE GEAR

a.
A131946

Wrap the chain around the gear.


b.

Using a vernier caliper, measure the No. 1 idle gear diameter with the chain.

Minimum gear diameter (with chain):

61.0 mm (2.40 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the chain and No. 1 idle gear.


Hide 11.INSPECT NO. 1 IDLE GEAR SHAFT OIL CLEARANCE

a.

Using a micrometer, measure the No. 1 idle gear shaft diameter.

Standard idle gear shaft diameter:

22.987 to 23.000 mm (0.905 to 0.906 in.)



b.

Using a caliper gauge, measure the inside diameter of the No. 1 idle gear.

Standard idle gear inside diameter:

23.02 to 23.03 mm (0.906 to 0.907 in.)



c.

Subtract the No. 1 idle gear shaft diameter measurement from the No. 1 idle gear inside diameter measurement.

Standard oil clearance:

0.020 to 0.043 mm (0.000787 to 0.00169 in.)


Maximum oil clearance:

0.093 mm (0.00366 in.)


If the shaft oil clearance is more than the maximum, replace the No. 1 idle gear shaft and No. 1 idle gear.


Hide 13540 12.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A120674C14
1.974,1.946 2.149,2.125 0.174,0.179 10 *1 1.072,1.84 1.269,2.028 0.198,0.188 10 *2 2.174,2.028 2.278,2.028 2.278,2.028 2.47,1.61 false 1.57,1.757 1.41,1.925 1.41,1.925 1.292,1.925 false 2.769,0.676 2.944,0.855 0.174,0.179 10 *a
*1 Plunger
*2 Stopper Plate
*a Moves Smoothly


Move the stopper plate upward to release the lock. Push the plunger and check that it moves smoothly.

If necessary, replace the No. 1 chain tensioner assembly.


Hide 13550 13.INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A385863C01
0.188,1.688 0.406,1.906 0.219,0.219 10 false *a 1.917,1.5 2.135,1.719 0.219,0.219 10 false *b 2.844,0.823 3.063,1.042 0.219,0.219 10 false *a
*a Depth
*b Moves Smoothly


Check that the plunger moves smoothly.


b.

Measure the depth of wear of the No. 2 chain tensioner assembly.

Maximum depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the No. 2 chain tensioner assembly.


Hide 13560A 14.INSPECT NO. 3 CHAIN TENSIONER ASSEMBLY

a.
A385865C01
0.177,1.698 0.365,1.917 0.188,0.219 10 false *a 2.896,0.802 3.083,1.021 0.188,0.219 10 false *a 1.958,1.448 2.146,1.698 0.188,0.25 10 false *b
*a Depth
*b Moves Smoothly


Check that the plunger moves smoothly.


b.

Measure the depth of wear of the No. 3 chain tensioner assembly.

Maximum depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the No. 3 chain tensioner assembly.


Hide 13559 15.INSPECT CHAIN TENSIONER SLIPPER

a.
A222118C09
2.927,1.354 3.135,1.521 0.208,0.167 10 false *a
*a Depth


Measure the depth of wear of the chain tensioner slipper.

Maximum depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the chain tensioner slipper.


Hide 13561 16.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.
A222119C10
2.948,1.594 3.146,1.781 0.198,0.188 10 false *a
*a Depth


Measure the depth of wear of the No. 1 chain vibration damper.

Maximum depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the No. 1 chain vibration damper.


Hide 13562 17.INSPECT NO. 2 CHAIN VIBRATION DAMPER

a.
A222120C09
3.073,1.427 3.292,1.625 0.219,0.198 10 false *a
*a Depth


Measure the depth of wear of the No. 2 chain vibration damper.

Maximum depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the No. 2 chain vibration damper.


Hide 18.INSPECT CAMSHAFT THRUST CLEARANCE


b.

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard thrust clearance:

0.08 to 0.13 mm (0.00315 to 0.00512 in.)


Maximum thrust clearance:

0.15 mm (0.00591 in.)


If the thrust clearance is more than the maximum, replace the camshaft housing sub-assembly.

If the thrust surface is damaged, replace the camshaft.


Hide 19.INSPECT CAMSHAFT OIL CLEARANCE

a.

Clean the camshaft bearing caps, camshaft housing and camshaft journals.


b.

Place the camshafts on the camshaft housing.


c.
A120715C14
1.583,0.938 1.156,1.677 1.156,1.677 0.99,1.677 false 0.833,1.583 1.042,1.781 0.208,0.198 10 false *a
*a Plastigage


Lay a strip of Plastigage across each camshaft journal.


d.

Install the camshaft bearing caps.

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>ENGINE UNIT>REASSEMBLY

NOTICE:

Do not turn the camshaft.



e.

f.
A221389C04
0.438,1.521 0.635,1.521 0.635,1.521 1.563,0.813 false 2.531,3.104 3.052,2.917 3.052,2.917 2.531,3.74 false 1.969,3.125 0.5,2.427 0.5,2.427 1.354,3.125 false 0.51,2.427 0.729,3.125 false 0.417,4.333 0.74,3.76 false 1.969,3.771 0.417,4.333 0.417,4.333 1.354,3.771 false 0.26,1.438 0.458,1.635 0.198,0.198 10 false *a 3.094,2.813 3.323,2.99 0.229,0.177 10 false *b 0.354,2.302 0.583,2.479 0.229,0.177 10 false *c 0.25,4.292 0.438,4.469 0.188,0.177 10 false *c
*a Plastigage
*b No. 1 Journal
*c Other Journals


Measure the Plastigage at its widest point.

Standard Oil Clearance:
Item Specified Condition
No. 1 journal 0.032 to 0.063 mm (0.00126 to 0.00248 in.)
Other journals 0.025 to 0.062 mm (0.000984 to 0.00244 in.)


Maximum Oil Clearance:
Item Specified Condition
No. 1 journal 0.10 mm (0.00394 in.)
Other journals 0.09 mm (0.00354 in.)


If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the camshaft housing sub-assembly.


Hide 17140 20.INSPECT EXHAUST MANIFOLD SUB-ASSEMBLY

a.
A222170

Using a precision straightedge and feeler gauge, measure the warpage of the surface which contacts the cylinder head.

Maximum warpage:

0.70 mm (0.0276 in.)


If the warpage is more than the maximum, replace the exhaust manifold sub-assembly.


Hide 17111 21.INSPECT INTAKE MANIFOLD FOR FLATNESS

a.
A222115C04
0.123,0.037 0.334,0.234 0.211,0.198 10 *a 0.123,2.039 0.334,2.237 0.211,0.198 10 *b
*a Intake Air Surge Tank Side
*b Cylinder Head Side


Using a precision straightedge and feeler gauge, measure the warpage of the surfaces which contact the cylinder head and intake air surge tank.

Maximum Warpage:
Item Specified Condition
Intake air surge tank side 0.80 mm (0.0315 in.)
Cylinder head side 0.20 mm (0.00787 in.)


If the warpage is more than the maximum, replace the intake manifold.