| *1 | CYLINDER BLOCK WATER DRAIN COCK PLUG | - | - |
| ● | Non-reusable part | ★ | Precoated part |
| *1 | OIL FILLER CAP SUB-ASSEMBLY | *2 | OIL CONTROL VALVE FILTER LH |
| *3 | OIL CONTROL VALVE FILTER RH | *4 | OIL FILTER CAP |
| *5 | OIL FILTER DRAIN PLUG | *6 | NO. 1 WATER BY-PASS HOSE |
| *7 | NO. 2 WATER BY-PASS HOSE | *8 | NO. 3 WATER BY-PASS HOSE |
| ● | Non-reusable part | - | - |
| *1 | SEAL WASHER | - | - |
| ● | Non-reusable part | ★ | Precoated part |
| ● | Non-reusable part | - | - |
| ● | Non-reusable part | - | - |
| *1 | CRANKSHAFT TIMING GEAR KEY | *2 | NO. 1 IDLE GEAR |
| *3 | NO. 2 IDLE GEAR SHAFT | - | - |
| ● | Non-reusable part | - | - |
| *1 | CAMSHAFT | *2 | NO. 2 CAMSHAFT |
| *3 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY (for Bank 1) | - | - |
| ● | Non-reusable part | - | - |
| *1 | NO. 3 CAMSHAFT | *2 | NO. 4 CAMSHAFT |
| *3 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY (for Bank 2) | - | - |
| ● | Non-reusable part | - | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 66 | STRAIGHT PIN | - | ( ) |
- | - |
| 67 | RING PIN | - | ( ) |
- | - |
| 68 | STUD BOLT | - | ( ) |
- | - |
| ● | Non-reusable part | - | - |
11415 3.REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
15330B 10.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side of Bank 1)
15340 12.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side of Bank 2)
12185 13.REMOVE OIL FILLER CAP HOUSING
16.REMOVE OIL FILTER ELEMENT
15671 17.REMOVE OIL FILTER BRACKET
18.REMOVE WATER INLET ASSEMBLY
16356 19.REMOVE REAR WATER BY-PASS JOINT
11202 23.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
11201 24.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
11193 25.REMOVE SPARK PLUG TUBE GASKET
| *a | Pry | - | - |
Bend the ventilation baffle plate claws on the cylinder head cover to an angle of 90° or more.
Remove the 6 spark plug tube gaskets.
Be careful not to damage the gasket when removing it as the removed gasket needs to be used when installing a new one.
12101A 27.REMOVE OIL PAN DRAIN PLUG
15104 29.REMOVE OIL STRAINER SUB-ASSEMBLY
12121 31.REMOVE NO. 1 OIL PAN BAFFLE PLATE
11381 32.REMOVE ENGINE REAR OIL SEAL RETAINER
| *a | Pry | - | - |
Remove the 5 bolts and 2 nuts.
Using a screwdriver, remove the engine rear oil seal retainer by prying between the engine rear oil seal retainer and crankshaft bearing cap.
Tape the screwdriver tip before use.
11381A 33.REMOVE REAR CRANKSHAFT OIL SEAL
Using a screwdriver and hammer, tap out the rear crankshaft oil seal.
Be careful not to damage the engine rear oil seal retainer.
16100 35.REMOVE ENGINE WATER PUMP ASSEMBLY
37.SET NO. 1 CYLINDER TO TDC/COMPRESSION
| *1 | Sensor Plate | - | - |
| *a | Center Line | *b | Timing Mark |
Temporarily install the pulley set bolt.
Turn the crankshaft clockwise to align the timing mark on the crank angle sensor plate with the RH block bore center line (TDC/compression).
Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.
If not, turn the crankshaft clockwise 1 revolution (360°) and align the timing marks as above.
13540 38.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
| *1 | Plunger | *2 | Stopper Plate |
| *3 | Pin | - | - |
Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
Move the stopper plate downward to set the lock, and insert a pin with a diameter of 1.27 mm (0.0500 in.) into the stopper plate hole.
Remove the 2 bolts and No. 1 chain tensioner assembly.
13559 39.REMOVE CHAIN TENSIONER SLIPPER
13506 40.REMOVE CHAIN SUB-ASSEMBLY
| *A | for Bank 1 | - | - |
| *1 | Sensor Plate | - | - |
| *a | Center Line | *b | Timing Mark |
Turn the crankshaft counterclockwise 10° to loosen the chain of the crankshaft timing sprocket.
Remove the pulley set bolt.
Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.
Turn the camshaft timing gear assembly on bank 1 clockwise approximately 60° so that it is as shown in the illustration. Be sure to loosen the chain sub-assembly between the banks.
Remove the chain sub-assembly.
13581 41.REMOVE NO. 1 IDLE GEAR SHAFT
Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, No. 1 idle gear and No. 1 idle gear shaft.
13561 42.REMOVE NO. 1 CHAIN VIBRATION DAMPER
13562 43.REMOVE NO. 2 CHAIN VIBRATION DAMPER
13521 44.REMOVE CRANKSHAFT TIMING SPROCKET
45.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)
| *1 | Pin | *2 | Plunger |
| *a | Push | *b | Turn |
| *c | Hold | - | - |
While raising the No. 2 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 2 chain tensioner assembly.
Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.
Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly with a new one.
Remove the 2 bolts and camshaft timing gear assembly together with the No. 2 chain.
13550 46.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY
47.REMOVE CAMSHAFT BEARING CAP (for Bank 1)
| *1 | Knock Pin | - | - |
| *a | Front View |
Check that the camshafts are positioned as shown in the illustration.
Uniformly loosen and remove the 8 bearing cap bolts in several steps in the sequence shown in the illustration.
Uniformly loosen and remove the 12 bearing cap bolts in several steps in the sequence shown in the illustration.
Uniformly loosen the bolts while keeping the camshaft level.
Remove the 5 camshaft bearing caps.
Remove the camshaft and No. 2 camshaft.
11103C 48.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH
| *1 | Protective Tape | - | - |
Remove the camshaft housing sub-assembly RH by prying between the cylinder head and camshaft housing sub-assembly RH with a screwdriver.
Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly RH.
Tape the screwdriver tip before use.
13801 49.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY (for Bank 1)
13750 50.REMOVE VALVE LASH ADJUSTER ASSEMBLY (for Bank 1)
13716 51.REMOVE VALVE STEM CAP (for Bank 1)
52.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)
| *1 | Pin | *2 | Plunger |
| *a | Push | *b | Turn |
| *c | Hold | - | - |
While pushing down the No. 3 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 3 chain tensioner assembly.
Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.
Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly with a new one.
Remove the 2 bolts and camshaft timing gear together with the No. 2 chain.
13560A 53.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY
54.REMOVE CAMSHAFT BEARING CAP (for Bank 2)
| *1 | Knock Pin | - | - |
| *a | Front View |
Check that the camshafts are positioned as shown in the illustration.
Uniformly loosen and remove the 8 bearing cap bolts in several steps in the sequence shown in the illustration.
Uniformly loosen and remove the 13 bearing cap bolts in several steps in the sequence shown in the illustration.
Uniformly loosen the bolts while keeping the camshaft level.
Remove the 5 camshaft bearing caps.
Remove the No. 3 camshaft and No. 4 camshaft.
11104A 55.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH
| *1 | Protective Tape | - | - |
Remove the camshaft housing sub-assembly LH by prying between the cylinder head and camshaft housing sub-assembly LH with a screwdriver.
Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly LH.
Tape the screwdriver tip before use.
13801 56.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY (for Bank 2)
13750 57.REMOVE VALVE LASH ADJUSTER ASSEMBLY (for Bank 2)
13716 58.REMOVE VALVE STEM CAP (for Bank 2)
11115 61.REMOVE CYLINDER HEAD GASKET
11116 62.REMOVE NO. 2 CYLINDER HEAD GASKET
16332 63.REMOVE NO. 1 WATER OUTLET PIPE
65.REMOVE CYLINDER BLOCK WATER JACKET SPACER
Remove the 2 cylinder block water jacket spacers from the cylinder block sub-assembly.
Be sure to remove the cylinder block water jacket spacers. If not, they may fall and become damaged when the cylinder block sub-assembly is inverted.
66.REMOVE STRAIGHT PIN
|
|
67.REMOVE RING PIN
|
|
68.REMOVE STUD BOLT
|
|
1. Using E6 and E8 "TORX" socket wrenches, remove the 6 stud bolts.
1. Using an E6 "TORX" socket wrench, removel the 2 stud bolts.