Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › CYLINDER HEAD
RM38G0E _51 Engine / Hybrid System _101207 1GR-FE ENGINE MECHANICAL _0469489 CYLINDER HEAD A

1GR-FE ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
A487701N01
0.083,0.167 2.667,1.75 2.583,1.583 5.427,3.479 6.198,3.667 0.771,0.188 1.042,0.417 1.813,0.604 0.771,0.188 5.5,3.896 6.438,4.083 0.938,0.188 1.573,2.542 2.198,2.729 0.625,0.188 4.844,4.458 5.469,4.646 0.625,0.188 0.542,4.656 1.219,4.854 0.677,0.198 1.99,1.875 2.667,2.073 0.677,0.198 0.771,0.521 1.031,0.521 true 3.281,5.375 3.583,5.375 true 2.219,5.313 2.594,5.313 true 3.656,1.125 3.781,1.125 3.781,1.125 3.875,1.448 true 3.521,1.552 3.677,1.552 3.677,1.552 3.813,1.792 true 2.677,1.969 2.833,1.969 2.833,1.969 3.01,2.25 true 1.229,4.76 1.438,4.76 1.438,4.76 1.229,4.365 true 4.583,4.542 4.833,4.542 true 2.208,2.635 2.323,2.635 2.323,2.635 2.469,2.719 true 3.781,2.281 4,2.281 true 4.875,2.198 5.042,2.375 5.042,2.375 5.208,2.375 true 4.625,2.5 4.896,2.958 4.896,2.958 5.094,2.958 true 1.313,3.781 1.51,3.781 true 2,3.083 2.354,3.083 true 3.615,0.708 3.771,0.708 3.771,0.708 3.906,0.948 true 3.667,0.365 3.823,0.365 3.823,0.365 3.958,0.604 true 4.125,0.323 4.531,0.323 true 5.427,1.458 5.833,1.458 true 5.625,1.156 6.031,1.156 true 5.771,0.896 6.177,0.896 true 2.51,2.469 2.917,2.469 true 1.51,4.292 1.667,4.604 1.667,4.604 1.865,4.604 true 5.083,1.885 5.25,2 5.25,2 5.417,2 true 4.969,3.375 5.219,3.594 5.219,3.594 5.417,3.594 true 4.948,5.156 5.385,5.156 true 5.219,3.99 5.49,3.99 true 3.885,5.24 4.271,5.594 0.385,0.354 18 false 12 1.896,5.188 2.271,5.573 0.375,0.385 18 false 13 3.375,0.99 3.719,1.333 0.344,0.344 18 false 11 3.208,1.427 3.583,1.813 0.375,0.385 18 false 10 3.167,2.208 3.417,2.448 0.25,0.24 10 false x 2 3.094,2.417 3.344,2.656 0.25,0.24 10 false x 2 1.813,1.854 2.156,2.198 0.344,0.344 18 false 9 0.354,4.625 0.698,4.969 0.344,0.344 18 false 8 6.813,3.865 7.094,4.219 0.281,0.354 18 false 7 5.833,4.417 6.177,4.76 0.344,0.344 18 false 7 1.365,2.521 1.708,2.865 0.344,0.344 18 false 7 5.01,4.052 5.26,4.292 0.25,0.24 10 false x 2 2.573,2.698 2.823,2.938 0.25,0.24 10 false x 2 4.469,4.594 4.719,4.833 0.25,0.24 10 false x 6 2.333,0.385 2.677,0.729 0.344,0.344 18 false 6 2.146,0.438 2.396,0.677 0.25,0.24 10 false ★ 6.542,3.49 6.792,3.729 0.25,0.24 10 false ★ 6.75,3.427 6.979,3.74 0.229,0.313 18 false 6 0.167,0.24 0.542,0.5 0.375,0.26 12 false *A 4.375,2.135 4.719,2.479 0.344,0.344 18 false 1 4.229,2.177 4.479,2.417 0.25,0.24 10 false ● 5.417,2.885 5.667,3.125 0.25,0.24 10 false ● 5.531,2.833 5.896,3.188 0.365,0.354 18 false 2 2.115,3.104 2.365,3.344 0.25,0.24 10 false x 2 1.604,3.771 1.854,4.01 0.25,0.24 10 false x 2 1.125,3.646 1.469,3.99 0.344,0.344 18 false 3 1.823,2.948 2.167,3.292 0.344,0.344 18 false 4 3.281,1.021 3.531,1.26 0.25,0.24 10 false ● 5.74,1.885 5.99,2.125 0.25,0.24 10 false ● 5.885,1.844 6.26,2.229 0.375,0.385 18 false 11 4.594,0.229 4.844,0.469 0.25,0.24 10 false *1 6.219,0.792 6.469,1.031 0.25,0.24 10 false *1 6.083,1.063 6.333,1.302 0.25,0.24 10 false *2 3.49,0.281 3.74,0.521 0.25,0.24 10 false *2 3.458,0.635 3.708,0.875 0.25,0.24 10 false *3 5.875,1.365 6.125,1.604 0.25,0.24 10 false *3 2.396,2.375 2.646,2.615 0.25,0.24 10 false ● 1.906,4.5 2.156,4.74 0.25,0.24 10 false ● 5.885,5.01 6.229,5.354 0.344,0.344 18 false 5 5.698,5.063 5.948,5.302 0.25,0.24 10 false ★ 5.458,3.51 6.219,3.719 0.76,0.208 8 false 14.7 (150, 11) 1.073,0.448 1.833,0.656 0.76,0.208 8 false 14.7 (150, 11) 5.531,3.917 6.521,4.146 0.99,0.229 8 false 4.0 (41, 35 in.*lbf) 1.625,2.563 2.396,2.75 0.771,0.188 8 false 10 (102, 7) 4.885,4.49 5.656,4.677 0.771,0.188 8 false 10 (102, 7) 0.583,4.688 1.354,4.875 0.771,0.188 8 false 80 (816, 59) 2.021,1.906 2.792,2.094 0.771,0.188 8 false 44 (449, 32) 5.24,2.229 5.615,2.615 0.375,0.385 18 false 10 1.677,2.979 1.927,3.219 0.25,0.24 10 false ● 1,3.688 1.25,3.927 0.25,0.24 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 INTAKE VALVE GUIDE BUSH 11122 (Click here) - -
2 EXHAUST VALVE GUIDE BUSH 11126 (Click here) - -
3 STRAIGHT PIN - (Click here) - -
4 RING PIN - (Click here) - -
5 SPARK PLUG TUBE - (Click here) - -
6 UNION - (Click here) - -
7 STUD BOLT - (Click here) - -
8 NO. 2 STRAIGHT SCREW PLUG 11117F (Click here) - -
9 NO. 1 STRAIGHT SCREW PLUG 11117E (Click here) - -
10 VALVE SPRING SEAT 13734 - - -
11 VALVE STEM OIL SEAL 13711E (Click here) - -
12 INTAKE VALVE 13711 (Click here) - -
13 EXHAUST VALVE 13715 (Click here) - -

*A for LH - -
*1 VALVE SPRING RETAINER LOCK *2 VALVE SPRING RETAINER
*3 INNER COMPRESSION SPRING - -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

Adhesive 1324 ★ Precoated part

PROCEDURE

Hide 11122 1.INSTALL INTAKE VALVE GUIDE BUSH

a.
A487717C01
1.708,3.635 1.208,4.438 1.208,4.438 1.76,3.792 true 0.406,0.063 0.885,0.448 0.479,0.385 18 false i, ii 4.198,0.052 4.677,0.438 0.479,0.385 18 false iii 0.406,2.708 0.927,3.104 0.521,0.396 18 false iv, v 4.188,2.719 4.708,3.115 0.521,0.396 18 false vi 1.031,4.469 1.427,4.708 0.396,0.24 10 false SST 3.042,3.26 3.188,3.458 0.146,0.198 10 true *a
*a Protrusion Height - -


i.

Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head.

Standard Bush Bore Diameter:
Item Specified Condition
STD 10.285 to 10.306 mm (0.4049 to 0.4057 in.)
O/S 0.05 10.335 to 10.356 mm (0.4069 to 0.4077 in.)



ii.

Select a new valve guide bush.

New Guide Bush:
Item Specified Condition
Bush Bore Diameter 10.285 to 10.306 mm (0.4049 to 0.4057 in.) 10.335 to 10.356 mm (0.4069 to 0.4077 in.)
Use Bush STD O/S 0.05


If the bush bore diameter of the cylinder head is more than 10.306 mm (0.4057 in.), machine the bush bore diameter to 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 valve guide bush.

If the bush bore diameter of the cylinder head is more than 10.356 mm (0.4077 in.), replace the cylinder head.

New Guide Bush Diameter:
Item Specified Condition
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


HINT:

Different bushes are used for the intake and exhaust.


Standard bush length:

41.3 to 41.7 mm (1.63 to 1.64 in.)



iii.

Heat the cylinder head to 80 to 100°C (176 to 212°F).

CAUTION:
·

Do not touch the cylinder head sub-assembly without wearing protective gloves, as it may get very hot during operation.

·

Be sure to wear protective gloves to avoid burns.




iv.

Place the cylinder head on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



v.

Using SST, tap in the intake valve guide bushes to the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard protrusion height:

9.10 to 9.90 mm (0.358 to 0.390 in.)



vi.

Using a sharp 5.5 mm reamer, ream the valve guide bushes to obtain the specified clearance.

Standard oil clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)




Hide 11126 2.INSTALL EXHAUST VALVE GUIDE BUSH

a.
A487718C01
1.563,3.51 0.563,4.354 0.563,4.354 1.531,3.698 true 0.406,0.052 0.865,0.448 0.458,0.396 18 false i, ii 4.167,0.052 4.625,0.448 0.458,0.396 18 false iii 0.427,2.708 0.979,3.073 0.552,0.365 18 false iv, v 4.177,2.698 4.729,3.063 0.552,0.365 18 false vi 0.396,4.385 0.76,4.604 0.365,0.219 10 false SST 2.844,3.979 3.021,4.177 0.177,0.198 10 true *a
*a Protrusion Height - -


i.

Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head.

Standard Bush Bore Diameter:
Item Specified Condition
STD 10.285 to 10.306 mm (0.4049 to 0.4057 in.)
O/S 0.05 10.335 to 10.356 mm (0.4069 to 0.4077 in.)



ii.

Select a new valve guide bush.

New Guide Bush:
Item Specified Condition
Bush Bore Diameter 10.285 to 10.306 mm (0.4049 to 0.4057 in.) 10.335 to 10.356 mm (0.4069 to 0.4077 in.)
Use Bush STD O/S 0.05


If the bush bore diameter of the cylinder head is more than 10.306 mm (0.4057 in.), machine the bush bore diameter to 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 valve guide bush.

If the bush bore diameter of the cylinder head is more than 10.356 mm (0.4077 in.), replace the cylinder head.

New Guide Bush Diameter:
Item Specified Condition
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


HINT:

Different bushes are used for the intake and exhaust.


Standard bush length:

46.8 to 47.2 mm (1.84 to 1.86 in.)



iii.

Heat the cylinder head to 80 to 100°C (176 to 212°F).

CAUTION:
·

Do not touch the cylinder head sub-assembly without wearing protective gloves, as it may get very hot during operation.

·

Be sure to wear protective gloves to avoid burns.




iv.

Place the cylinder head on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



v.

Using SST, tap in the intake valve guide bushes to the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard protrusion height:

9.10 to 9.90 mm (0.358 to 0.390 in.)



vi.

Using a sharp 5.5 mm reamer, ream the valve guide bushes to obtain the specified clearance.

Standard oil clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)




Hide 3.INSTALL STRAIGHT PIN

Z101186

NOTICE:

If a straight pin is deformed, replace it.



a.
A487720C01
0.438,0.031 0.719,0.385 0.281,0.354 18 false i 1.26,0.26 1.542,0.615 0.281,0.354 10 false *a 4.469,0.26 4.75,0.615 0.281,0.354 10 false *b 6.698,0.844 6.979,1.198 0.281,0.354 10 false *c
*a for Bank 1 *b for Bank 2
*c Protrusion Height - -


i.

Using a plastic-faced hammer, tap in new straight pins as shown in the illustration.

Standard protrusion height:

18.0 to 19.0 mm (0.708 to 0.748 in.)




Hide 4.INSTALL RING PIN

Z101186

NOTICE:

It is not necessary to remove a ring pin unless it is being replaced.



a.
A487721C01
0.99,0.604 1.271,0.833 0.281,0.229 10 false *a 0.958,2.115 1.271,2.313 0.313,0.198 10 false *b 5.698,1.323 6.01,1.521 0.313,0.198 10 false *c 0.365,0.052 0.646,0.406 0.281,0.354 18 false i
*a for Bank 1 *b for Bank 2
*c Protrusion Height - -


i.

Using a plastic-faced hammer, tap in new ring pins to the specified protrusion height.

Standard protrusion height:

2.5 to 3.5 mm (0.0984 to 0.138 in.)




Hide 5.INSTALL SPARK PLUG TUBE

Z101186

HINT:

When using a new cylinder head, the spark plug tubes must be replaced.



a.
A487722C01
2.635,2.74 2.635,2.219 true 0.5,1.115 0.781,1.469 0.281,0.354 18 false i 3.969,0.135 4.25,0.49 0.281,0.354 18 false ii 2.063,1.667 2.375,1.927 0.313,0.26 10 false *b 2.563,2.771 2.875,3.031 0.313,0.26 10 false *a 1.969,2.844 2.281,3.104 0.313,0.26 10 false *c 4.865,2.583 5.177,2.844 0.313,0.26 10 false *d
*a Adhesive *b 1.0 to 3.0 mm (0.394 to 0.118 in.)
*c 9.0 to 15.0 mm (0.354 to 0.590 in.) *d Protrusion Height


i.

Apply adhesive to the end of a new spark plug tube.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.


Standard seal diameter:

1.0 to 3.0 mm (0.394 to 0.118 in.)


Distance:

9.0 to 15.0 mm (0.354 to 0.590 in.)


NOTICE:
·

Be careful not to deform the spark plug tube.

·

Be careful not to expose the seal to coolant for at least 1 hour after installing it.




ii.

Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.

Standard protrusion height:

75.1 to 76.1 mm (2.96 to 3.00 in.)


NOTICE:

To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.




Hide 6.INSTALL UNION

Z101186

NOTICE:

If a union is deformed, replace it.



a.
A487712C01
1.531,0.115 1.885,0.344 0.354,0.229 10 false *A 5.135,0.094 5.49,0.323 0.354,0.229 10 false *B 0.313,1.094 0.667,1.323 0.354,0.229 10 false *a 3.531,1.125 3.885,1.354 0.354,0.229 10 false *b 0.49,0.073 0.917,0.406 0.427,0.333 18 false i, ii 2.219,2.719 2.573,2.948 0.354,0.229 10 false *c 5.76,2.906 6.115,3.135 0.354,0.229 10 false *d
*A for Bank 1 *B for Bank 2
*a Front Side *b Intake Port Side
*c 67 mm (2.64 in.) *d 30 mm (1.18 in.)


i.

Apply adhesive to 2 or 3 threads of the bolt ends of unions.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



ii.

Using a 12 mm deep socket wrench, install the 2 unions.

Torque:
14.7 N*m (150 kgf*cm, 11 ft.*lbf)



Hide 7.INSTALL STUD BOLT

Z101186

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.



a.
A487713C01
3.833,0.083 7.083,4.583 3.25,4.5 0.25,0.333 7.083,1.583 6.833,1.25 0.25,1.583 7.083,3.333 6.833,1.75 0.25,3.333 7.083,4.583 6.833,1.25 0.583,0.083 3.833,4.583 3.25,4.5 2.083,4.833 2.396,5.063 0.313,0.229 10 false *d 2.094,5.333 2.406,5.563 0.313,0.229 10 false *e 2.427,5.073 2.74,5.302 0.313,0.229 10 false *f 5.823,4.979 6.135,5.208 0.313,0.229 10 false *g 5.833,5.375 6.146,5.604 0.313,0.229 10 false *h 6.167,5.177 6.479,5.406 0.313,0.229 10 false *i 1.656,5.594 1.969,5.823 0.313,0.229 10 false A 5.427,5.594 5.74,5.823 0.313,0.229 10 false B 0.344,0.031 0.625,0.385 0.281,0.354 18 false i 2.073,0.125 2.354,0.479 0.281,0.354 10 false *A 5.448,0.125 5.729,0.479 0.281,0.354 10 false *B 0.344,0.875 0.625,1.229 0.281,0.354 10 false *a 0.344,2.406 0.625,2.76 0.281,0.354 10 false *b 0.344,3.917 0.625,4.271 0.281,0.354 10 false *c 1.24,1.052 1.417,1.281 0.177,0.229 10 true A 3.135,1.073 3.313,1.302 0.177,0.229 10 true A 4.469,1.063 4.646,1.292 0.177,0.229 10 true A 6.333,1.052 6.51,1.281 0.177,0.229 10 true A 1.615,2 1.771,2.188 0.156,0.188 10 true A 2.271,2.021 2.427,2.208 0.156,0.188 10 true A 2.729,2.229 2.885,2.417 0.156,0.188 10 true A 2.458,3.073 2.615,3.26 0.156,0.188 10 true A 1.781,3.073 1.938,3.26 0.156,0.188 10 true A 0.979,3.073 1.104,3.26 0.125,0.188 10 true A 5.427,3.052 5.583,3.24 0.156,0.188 10 true A 6.094,3.063 6.25,3.25 0.156,0.188 10 true A 5.917,2.01 6.052,2.198 0.135,0.188 10 true A 5.26,2.01 5.396,2.198 0.135,0.188 10 true A 4.604,3.073 4.76,3.26 0.156,0.188 10 true A 6.063,3.469 6.219,3.656 0.156,0.188 10 true B 5.885,4.365 6.042,4.552 0.156,0.188 10 true B 1.802,4.354 1.958,4.542 0.156,0.188 10 true B 1.438,3.469 1.594,3.656 0.156,0.188 10 true B
*A for Bank 1 *B for Bank 2
*a Intake Side *b Exhaust Side
*c Rear Side *d 20 mm (0.787 in.)
*e 13 mm (0.512 in.) *f 35 mm (1.378 in.)
*g 16 mm (0.630 in.) *h 9 mm (0.354 in.)
*i 27 mm (1.063 in.) - -


i.

Using E6 and E8 "TORX" sockets, install the stud bolts.

Torque:
for stud bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for stud bolt B : 4.0 N*m (41 kgf*cm, 35 in.*lbf)



Hide 11117F 8.INSTALL NO. 2 STRAIGHT SCREW PLUG

a.
A487707C01
1.958,0.063 2.271,0.26 0.313,0.198 10 false *A 5.896,0.073 6.208,0.271 0.313,0.198 10 false *B 0.75,0.042 1.104,0.365 0.354,0.323 18 false i 4.406,0.031 4.76,0.354 0.354,0.323 18 false i
*A for Bank 1 *B for Bank 2


i.

Using a 14 mm hexagon wrench, install 2 new gaskets and the 2 No. 2 straight screw plugs.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)



Hide 11117E 9.INSTALL NO. 1 STRAIGHT SCREW PLUG

a.
A487706C01
0.708,0.021 0.99,0.375 0.281,0.354 18 false i 4.385,0.031 4.667,0.385 0.281,0.354 18 false i 1.792,0.083 2.073,0.438 0.281,0.354 10 false *A 5.417,0.094 5.698,0.448 0.281,0.354 10 false *B
*A for Bank 1 *B for Bank 2


i.

Using a 10 mm hexagon wrench, install 4 new gaskets and the 4 No. 1 straight screw plugs.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)



Hide 13734 10.INSTALL VALVE SPRING SEAT

Hide 13711E 11.INSTALL VALVE STEM OIL SEAL

a.
A487714C01
4.177,0.677 5.115,0.677 true 0.875,0.563 0.875,0.302 0.875,0.302 1.063,0.302 true 2.448,0.552 2.448,0.292 2.448,0.292 2.635,0.292 true 4.469,1.094 4.74,1.292 0.271,0.198 10 false *a 5.5,1.104 5.76,1.292 0.26,0.188 10 false *b 1.094,0.198 1.344,0.396 0.25,0.198 10 false *c 2.667,0.188 2.927,0.385 0.26,0.198 10 false *d 0.813,1.344 1.073,1.573 0.26,0.229 10 false *e 2.427,1.344 2.688,1.552 0.26,0.208 10 false *f 0.427,0.021 0.76,0.406 0.333,0.385 18 false i 3.854,0.031 4.188,0.417 0.333,0.385 18 false ii 3.875,0.604 4.188,0.813 0.313,0.208 10 false SST
*a Correct *b Incorrect
*c Gray *d Black
*e Intake Side *f Exhaust Side


i.

Apply a light coat of engine oil to new valve stem oil seals.

NOTICE:

Pay attention when installing the intake and exhaust valve stem oil seals. For example, installing the intake valve stem oil seal to the exhaust side or installing the exhaust valve stem oil seal to the intake side can cause installation problems later.


HINT:

The intake valve oil seals are gray and the exhaust valve oil seals are black.



ii.

Using SST, push in the oil seals.

SST
09201-41020  

NOTICE:

Failure to use SST will cause the seal to be damaged or improperly seated.




Hide 13711 12.INSTALL INTAKE VALVE

a.
A488495C01
5.396,0.604 5.469,0.365 5.469,0.365 5.646,0.365 true 0.542,0.167 0.823,0.521 0.281,0.354 18 false i 4.198,0.135 4.677,0.406 0.479,0.271 18 true ii, iii 1.781,2 2.031,2.281 0.25,0.281 18 true iv 2.604,1.51 2.854,1.792 0.25,0.281 10 false *a 5.698,0.271 6.042,0.521 0.344,0.25 10 false SST
*a 30 mm (1.18 in.) or more - -


i.

Apply a sufficient coat of engine oil to the tip area of the intake valve shown in the illustration.


ii.

Install the intake valve, inner compression spring and valve spring retainer to the cylinder head.

NOTICE:

Install the same parts in the same combination to their original locations.



iii.

Using SST, compress the inner compression spring and install the valve spring retainer lock.

SST
09202-70020  (09202-00010)


iv.

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to damage the retainer.




Hide 13715 13.INSTALL EXHAUST VALVE

a.
A488496C01
6.177,0.594 6.063,0.323 6.063,0.323 5.938,0.323 true 0.531,0.146 0.813,0.5 0.281,0.354 18 false i 3.771,0.156 4.271,0.51 0.5,0.354 18 false ii, iii 1.771,2.021 2.271,2.375 0.5,0.354 18 false iv 2.583,1.51 2.885,1.76 0.302,0.25 10 false *a 5.656,0.25 6.021,0.469 0.365,0.219 10 false SST
*a 30 mm (1.18 in.) or more - -


i.

Apply a sufficient coat of engine oil to the tip area of the exhaust valve shown in the illustration.


ii.

Install the exhaust valve, inner compression spring and valve spring retainer to the cylinder head.

NOTICE:

Install the same parts in the same combination to the original locations.



iii.

Using SST, compress the inner compression spring and install the valve spring retainer lock.

SST
09202-70020  (09202-00010)


iv.

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to damage the retainer.