Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100728 PARK ASSIST / MONITORING _0469672 PARKING ASSIST MONITOR SYSTEM U

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  TERMINALS OF ECU  


REAR TELEVISION CAMERA ASSEMBLY


E286120N48
3.292,0.094 3.813,0.344 0.521,0.25 3.458,0.115 3.698,0.323 0.24,0.208 10 false g9

a.

Disconnect the g9 rear television camera assembly connector.


b.

Measure the voltage on the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
g9-6 (CB+) - Body ground Power source Ignition switch ACC 5.5 to 7.05 V


c.

Reconnect the g9 rear television camera assembly connector.


d.

Measure the resistance and check for pulses at each terminal of the connector.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
g9-3 (CV+) - g9-2 (CV-) Video signal Ignition switch ON
Shift position in R
Camera lens not covered, displaying image
Pulse generation
(Refer to waveform 1)
Ignition switch ON
Shift position in R
Camera lens covered, blacking out screen
Pulse generation
(Refer to waveform 2)
g9-5 (CGND) - Body ground Camera ground Always Below 1 Ω


e.
E265840C04
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens not covered, displaying image)
*b Waveform 2 (camera lens covered, blacking out screen)
*c Synchronization Signal
*d Video Waveform


Reference (Oscilloscope waveform):

i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Measurement terminal g9-3 (CV+) - g9-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Ignition switch ON, shift position in R, camera lens not covered, displaying image

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the ignition switch is ACC.




ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Measurement terminal g9-3 (CV+) - g9-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Ignition switch ON, shift position in R, camera lens covered, blacking out screen

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the ignition switch is ACC.