Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100728 PARK ASSIST / MONITORING _0469672 PARKING ASSIST MONITOR SYSTEM D

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  DIAGNOSIS SYSTEM  


PARKING ASSIST MONITOR SYSTEM DIAGNOSTIC MODE


a.

In diagnostic mode for the parking assist monitor system, signals received by the multi-display assembly*1 or radio and display receiver assembly*2 can be checked and the parking assist monitor system can be calibrated, adjusted and checked using the multi-display assembly*1 or radio and display receiver assembly*2

*1: for 12.3 Inch Display

*2: except 12.3 Inch Display

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION


HINT:

The displayed items may differ depending on vehicle specifications.




DIAGNOSIS SCREEN TRANSITION (DURING PARKING ASSIST MONITOR SYSTEM INITIALIZATION)


E410097E01
2.969,1.073 4.906,1.333 1.938,0.26 10 false Start diagnostic mode 0.229,0.135 1.24,0.417 1.01,0.281 12 false Example:

E378701E04
2.021,0.698 2.333,0.896 0.313,0.198 10 false or


DIAGNOSIS SCREEN TRANSITION (AFTER PARKING ASSIST MONITOR SYSTEM INITIALIZATION)


E404580E02
5.292,3.802 5.604,4 0.313,0.198 10 false or 1.073,3.896 1.385,4.094 0.313,0.198 10 false or 3.01,1.052 4.802,1.26 1.792,0.208 10 false Start diagnostic mode 0.167,0.125 1.229,0.448 1.063,0.323 12 false Example: 5.146,7.469 5.458,7.667 0.313,0.198 10 false or

E378703


VEHICLE SIGNAL CHECK


HINT:

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.



b.
E271944

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.


c.
E404579

Select "Vehicle Signal" on the "Function Check/Setting I" screen.


d.
E225776

Vehicle Signal Check Mode

i.

When the "Vehicle Signal Check Mode" screen is displayed, check the item displayed for "REV".

w/ Navigation System:

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

w/ Audio and Visual System (for Radio and Display Type, except 12.3 Inch Display):

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)>DTC CHECK / CLEAR

w/ Audio and Visual System (for Radio and Display Type, for 12.3 Inch Display):

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, for 12.3 Inch Display)>DTC CHECK / CLEAR

HINT:
·

Only conditions having inputs are displayed.

·

This screen displays vehicle signals input to the radio receiver assembly*1 or radio and display receiver assembly*2.

*1: for 12.3 Inch Display

*2: except 12.3 Inch Display





e.


SIGNAL CHECK (PARKING ASSIST MONITOR SYSTEM INPUT SIGNALS)


HINT:

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


a.

Start diagnostic mode.

w/ Navigation System:

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

w/ Audio and Visual System (for Radio and Display Type, except 12.3 Inch Display):

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)>DTC CHECK / CLEAR

w/ Audio and Visual System (for Radio and Display Type, for 12.3 Inch Display):

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, for 12.3 Inch Display)>DTC CHECK / CLEAR

i.
E271944

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.


ii.
E404579

Select "Camera Setting" on the "Function Check/Setting I" screen.

NOTICE:

If the "Camera Setting" selection screen is not displayed, turn the ignition switch off and enter the diagnosis screen after turning the ignition switch to ON once again.


HINT:

After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the parking assist monitor system was performed after the rear television camera assembly was replaced.

Parking Assist Monitor System Initialization Screen Transition
Not performed Signal Check (*) screen
Performed Mode Setting (*) screen



iii.
E378699

When the screen changes to the "Mode Setting (*)" screen, select "Back Camera Setting" to display the "Signal Check (*)" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.




b.
E366772

Signal Check

i.

On the "Signal Check (*)" screen, it is possible to inspect the state of signals and check the settings.

Item Inspection Detail Note
CAN CAN communication signal input When "CHK" (red) is displayed, selecting "Next" will not change the screen to the next screen.

HINT:
·

When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.

·

If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "Next".





c.

CAN inspection

HINT:

If "CHK" (red) is displayed for "CAN", check for DTCs and perform troubleshooting based on the output DTCs.



d.


CAMERA SYNCHRONOUS ERROR HISTORY


HINT:

This function is used to check the date and time of occurrence when a camera synchronous error occurs.


a.

Check camera synchronous error history.

i.

Read the Utility according to the display on the GTS.

Body Electrical > Navigation System > Utility
Tester Display
Camera Synchronous Error History
50005 212 4285

ii.

When an item is stored for Camera Synchronous Error History, record it before repairing the radio receiver assembly*1 or radio and display receiver assembly*2 and rear television camera assembly.

*1: for 12.3 Inch Display

*2: except 12.3 Inch Display

HINT:

Camera Synchronous Error History can store up to 5 history data items. If a new camera synchronous error occurs when 5 data items have already been stored, the oldest data is cleared and new data is stored.




b.

Clear camera synchronous error history.

i.

When DTCs are cleared using any of the following operations, Camera Synchronous Error History will be cleared as well.

w/ Navigation System:

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

w/ Audio and Visual System (for Radio and Display Type, except 12.3 Inch Display):

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)>DTC CHECK / CLEAR

w/ Audio and Visual System (for Radio and Display Type, for 12.3 Inch Display):

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, for 12.3 Inch Display)>DTC CHECK / CLEAR

·

Cleared using the GTS.

·

Cleared using the system check mode screen.

·

Cleared using the unit check mode screen.





VIDEO DEVICE CONNECTION CHECK


w/ Navigation System:

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

w/ Audio and Visual System (for Radio and Display Type, except 12.3 Inch Display):

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)>DTC CHECK / CLEAR

w/ Audio and Visual System (for Radio and Display Type, for 12.3 Inch Display):

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, for 12.3 Inch Display)>DTC CHECK / CLEAR


CALIBRATION WHEN SERVICING VEHICLE


NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION