Home › Drivetrain › JF2BM (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM
RM38G0E _52 Drivetrain _100437 JF2BM TRANSFER / 4WD / AWD _0467431 TRANSFER SYSTEM C

JF2BM TRANSFER / 4WD / AWD  TRANSFER SYSTEM  P17B811  4WD/AWD Front Differential Unit Actuator "A" Control Circuit Circuit Short to Ground  P17B812  4WD/AWD Front Differential Unit Actuator "A" Control Circuit Circuit Short to Battery  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
P17B811 4WD/AWD Front Differential Unit Actuator "A" Control Circuit Circuit Short to Ground
Diagnosis Condition:
·

Ignition switch ON

·

Front differential lock solenoid is not powered on or is operated


Malfunction Status:
·

Front differential lock solenoid drive circuit monitor voltage is less than malfunction detection voltage


Malfunction Time:
·

1 second or more


Number of Trips:
·

1 trip


·

Wire harness and connector

·

Front differential lock solenoid (No. 1 front differential case sub-assembly)

·

4 wheel drive control ECU


Four Wheel Drive
P17B812 4WD/AWD Front Differential Unit Actuator "A" Control Circuit Circuit Short to Battery
Diagnosis Condition:
·

Ignition switch ON

·

Front differential lock solenoid is not powered on or is operated


Malfunction Status:
·

Front differential lock solenoid drive circuit monitor voltage exceeds malfunction detection voltage


Malfunction Time:
·

1 second or more


Number of Trips:
·

1 trip


·

Wire harness and connector

·

Front differential lock solenoid (No. 1 front differential case sub-assembly)

·

4 wheel drive control ECU


Four Wheel Drive

DTC Detection Conditions: P17B811
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Ignition switch ON ○ ○
Front differential lock solenoid is not powered on ○ -
Front differential lock solenoid is operated - ○
Malfunction Status Front differential lock solenoid drive circuit monitor voltage is less than malfunction detection voltage ○ ○
Detection Time 1 second or more 1 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: P17B812
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Ignition switch ON ○ ○
Front differential lock solenoid is not powered on ○ -
Front differential lock solenoid is operated - ○
Malfunction Status Front differential lock solenoid drive circuit monitor voltage exceeds malfunction detection voltage ○ ○
Detection Time 1 second or more 1 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C456156E04
3.771,1.365 4.177,1.583 0.406,0.219 10 false FSL+ 3.75,1.927 4.156,2.146 0.406,0.219 10 false FSL- 4.25,1.375 4.458,1.573 0.208,0.198 10 false 5 4.25,1.958 4.458,2.156 0.208,0.198 10 false 4 5.885,1.375 6.344,1.573 0.458,0.198 10 false SL+ 5.896,1.958 6.354,2.156 0.458,0.198 10 false SL- 5.583,1.396 5.771,1.594 0.188,0.198 10 false 2 5.583,1.938 5.771,2.135 0.188,0.198 10 false 1 5.167,2.375 5.479,2.573 0.313,0.198 10 false H1 5.177,2.635 7.135,2.948 1.958,0.313 10 false Front Differential Lock Solenoid (No. 1 Front Differential Case Sub-assembly) 0.26,5.448 0.719,5.646 0.458,0.198 10 false B11 0.26,5.667 4.083,5.865 3.823,0.198 10 false 4 Wheel Drive Control ECU 1.938,0.906 2.396,1.104 0.458,0.198 10 false IPD 1.24,2.135 2.875,2.354 1.635,0.219 10 false Current Detection Circuit 1.448,4.354 2.385,4.563 0.938,0.208 10 false Drive Circuit 0.531,2.417 0.99,2.615 0.458,0.198 10 false CPU 1.406,3.51 1.563,3.708 0.156,0.198 10 false * 0.948,6.375 3.896,6.573 2.948,0.198 10 false *: Solenoid Drive Circuit Monitor Voltage 0.99,6.958 5.729,7.156 4.74,0.198 10 false IPD: Abbreviation for Intelligent Power Device 3.292,0.365 3.75,0.563 0.458,0.198 10 false IGR 1.229,0.542 1.688,0.74 0.458,0.198 10 false Vcc

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SUPPLY - 4 WHEEL DRIVE CONTROL ECU)
a.

Disconnect the B11 4 wheel drive control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B11)Location & Routing

Click Connector(B11)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>4 Wheel Drive Control ECU

B11-5 (FSL+) - Body ground Ignition switch off Below 1.5 V
B11-5 (FSL+) - Body ground Ignition switch ON Below 1.5 V
B11-4 (FSL-) - Body ground Ignition switch off Below 1.5 V
B11-4 (FSL-) - Body ground Ignition switch ON Below 1.5 V



c.

Connect the B11 4 wheel drive control ECU connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - BODY GROUND)
a.

Disconnect the B11 4 wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B11)Location & Routing

Click Connector(B11)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>4 Wheel Drive Control ECU

B11-5 (FSL+) - Body ground Always 10 kΩ or higher
B11-4 (FSL-) - Body ground Always 10 kΩ or higher



c.

Connect the B11 4 wheel drive control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - BODY GROUND)
a.

Disconnect the B11 4 wheel drive control ECU connector.


b.

Disconnect the H1 front differential lock solenoid (No. 1 front differential case sub-assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B11)Location & Routing

Click Connector(B11)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>4 Wheel Drive Control ECU

B11-5 (FSL+) - Body ground Always 10 kΩ or higher
B11-4 (FSL-) - Body ground Always 10 kΩ or higher



d.

Connect the H1 front differential lock solenoid (No. 1 front differential case sub-assembly) connector.


e.

Connect the B11 4 wheel drive control ECU connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 FRONT DIFFERENTIAL CASE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR