Home › Engine / Hybrid System › V35A-FTS (FUEL) › FUEL SYSTEM
RM38G0E _51 Engine / Hybrid System _101368 V35A-FTS FUEL _0470020 FUEL SYSTEM L

V35A-FTS FUEL  FUEL SYSTEM  PRECAUTION  


CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A344817

Because the weight of the fuel tank sub-assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the components could fall down.



BEFORE WORKING ON FUEL SYSTEM


a.

Before inspecting and repairing the fuel system, disconnect the cable from the negative (-) battery terminal.

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY



b.

Do not smoke or work near fire when performing work on the fuel system.


c.

Keep fuel away from rubber or leather parts.



DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

Make sure the engine coolant temperature is 80 °C (176 °F) or more when performing this procedure.

·

Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.

·

Pressure will still remain in the fuel lines even after performing the following procedure. When disconnecting a fuel line, cover it with a piece of cloth to prevent fuel from spraying or coming out.



a.

Remove the No. 2 relay block cover.


b.
A482125

Remove the EFI-MAIN No. 2 relay.


c.

Start the engine and slightly depress the accelerator pedal. After the engine has stopped on its own, turn the ignition switch off. [*1]


d.

Perform [*1] approximately 2 to 3 times.

NOTICE:

Make sure the engine coolant temperature is 80 °C (176 °F) or more when performing this procedure.


HINT:

DTCs or Vehicle Control History may be stored when this procedure. Clear the DTCs or Vehicle Control History.



e.

Loosen the fuel tank cap assembly, and then discharge the pressure in the fuel tank completely.


f.

Install the fuel tank cap assembly.


g.

Install the EFI-MAIN No. 2 relay.


h.

Install the No. 2 relay block cover.


i.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY




FUEL LINE


a.

When disconnecting a high-pressure fuel line, a large amount of fuel will spray. Perform the following procedure:

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.

Discharge fuel system pressure.


ii.

Disconnect the fuel tube.


iii.

Drain the fuel remaining inside the fuel pump tube into a container.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.


v.

Put a container under the connection.



b.

Perform the following procedure when disconnecting the fuel tube connector (for quick type A).

i.

Check for dirt or mud on the pipe and around the connector before disconnection. Clean if necessary.


ii.
A147380C01
0,0 0,0 false
V100135

Pinch
V100136

Pull


Pinch the connector and disconnect the connector and pipe.

If the connector and the pipe are stuck together, pinch the connector, and then push and pull the pipe to disconnect the pipe and pull it out.

NOTICE:
·
A220697C03
1.458,1.771 1.458,1.188 true 1.458,1.51 1.302,1.51 1.302,1.51 1.302,1.177 true 0.583,1.729 0.75,1.729 0.75,1.729 1,1.313 true 0.813,1.052 0.479,1.052 true 0.646,0.458 0.813,0.458 0.813,0.458 0.99,0.875 true 2.604,0.469 2.406,0.469 2.406,0.469 2.198,0.885 true 1.396,1.802 1.583,1.99 0.188,0.188 10 false *a 0.396,1.646 0.594,1.833 0.198,0.188 10 false *b 0.281,0.958 0.479,1.146 0.198,0.188 10 false *c 0.458,0.365 0.656,0.563 0.198,0.198 10 false *d 2.646,0.375 2.833,0.573 0.188,0.198 10 false *e
*a O-Ring
*b Connector
*c Pipe
*d Retainer
*e Nylon Tube


Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.




iii.

Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.


iv.

To protect the disconnected pipe and connector from damage and contamination, cover them with a plastic bag.



c.

Perform the following procedure when connecting the fuel tube connector (for quick type A).

i.

Check that there is no damage or contamination in the connected part of the pipe.


ii.
A284670C01
1.646,1.667 1.719,1.635 false
V100135

Push


Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh spindle oil or gasoline on the tip of the pipe.

NOTICE:
·
A220697C03
1.458,1.771 1.458,1.188 true 1.458,1.51 1.302,1.51 1.302,1.51 1.302,1.177 true 0.583,1.729 0.75,1.729 0.75,1.729 1,1.313 true 0.813,1.052 0.479,1.052 true 0.646,0.458 0.813,0.458 0.813,0.458 0.99,0.875 true 2.604,0.469 2.406,0.469 2.406,0.469 2.198,0.885 true 1.396,1.802 1.583,1.99 0.188,0.188 10 false *a 0.396,1.646 0.594,1.833 0.198,0.188 10 false *b 0.281,0.958 0.479,1.146 0.198,0.188 10 false *c 0.458,0.365 0.656,0.563 0.198,0.198 10 false *d 2.646,0.375 2.833,0.573 0.188,0.198 10 false *e
*a O-Ring
*b Connector
*c Pipe
*d Retainer
*e Nylon Tube


Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.

·

After connecting the connectors and pipes, check if they are securely connected by trying to pull them apart.




iii.
A303841C01
1.542,1.563 1.698,1.76 0.156,0.198 10 false .
V100135

Pull


After having finished the connection, try to pull apart the pipe and connector to confirm that they are securely connected.


iv.

Check that there is no fuel leakage.



d.

Perform the following procedure when disconnecting a fuel tube connector (for quick type B).

i.

Check that there is no damage or foreign matter on the part of the fuel pipe that contacts the connector.


ii.
A293606C15
2.552,1.052 2.677,1.052 2.677,1.052 2.771,1.24 false 2.375,0.99 2.583,1.135 0.208,0.146 10 false *a
*a Retainer
V100135

Pull
V100136

Pull out


Pull the tabs of the fuel tube connector retainer as shown in the illustration to disconnect the fuel tube connector from the fuel pipe.

HINT:
A293524C07
0,0 0,0 false
V100135

Pull
V100136

Push


If the connector and fuel pipe are stuck, pinch the fuel pipe by hand and push and pull the connector to disconnect it.


NOTICE:
·

Check for any dirt and foreign matter contamination in the fuel pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the fuel pipe and fuel tube connector.

·

Do not use any tools to separate the fuel pipe and fuel tube connector.

·

Check for any dirt and foreign matter on the fuel pipe seal surface. Clean if necessary.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tube.

·

If the fuel pipe and fuel tube connector are stuck together, pinch the connector between your fingers and turn it carefully to free it. Then disconnect the fuel tube.




iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel pipes. Clean the surfaces if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with a plastic bag to prevent damage and contamination.



e.

Perform the following procedure when connecting a fuel tube connector (for quick type B).

i.

Check if there is any damage or foreign matter on the connecting parts of the fuel pipe.


ii.
A293526C14
2.688,1.292 2.417,1.125 2.417,1.125 2.281,1.125 false 2.094,1.042 2.406,1.198 0.313,0.156 10 false *a
*a Retainer
V100135

Push
V100136

Push Down


Line up the fuel pipe and fuel tube connector and push them together until a "click" sound is heard. If the connection is tight, apply a small amount of fresh engine oil to the tip of the fuel pipe.


iii.

Push down the retainer.


iv.
A293527C10
0,0 0,0 false
V100135

Pull


After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.


v.

Install the fuel hose clamp.


vi.

Attach the claw to close the cover of the fuel hose clamp.


vii.

Inspect for fuel leaks.



f.

Perform the following procedure when disconnecting a fuel tube connector (for quick type C).

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.

Check that there is no damage or foreign matter on the part of the fuel pipe that contacts the connector.


ii.
A224877C24
2.521,1.771 2.177,1.771 false 1.958,1.677 2.146,1.833 0.188,0.156 10 false *a
*a Retainer
V100135

Push
V100136

Down
V100137

Pull


Detach the 2 claws of the connector retainer. Push down on the connector and disconnect it from the pipe.

HINT:
A270474C02
2.635,1.5 2.948,1.656 0.313,0.156 10 false .
V100135

Pull
V100136

Push


If the connector and fuel pipe are stuck, pinch the fuel pipe by hand and push and pull the connector to disconnect it.


NOTICE:
·
A224889C27
1.052,1.594 1.052,1.354 false 1.896,1.188 1.896,1.708 false 2.125,1.719 1.708,1.719 1.708,1.719 1.708,1.198 false 0.604,0.302 0.521,0.302 false 0.521,0.302 0.521,0.927 false 1.438,0.302 1.365,0.302 1.365,0.302 1.094,0.74 false 2.948,0.302 2.875,0.302 2.875,0.302 2.729,0.781 false 0.656,0.24 0.969,0.396 0.313,0.156 10 false *b 1.5,0.229 1.813,0.385 0.313,0.156 10 false *a 2.979,0.229 3.292,0.385 0.313,0.156 10 false *c 0.938,1.615 1.25,1.771 0.313,0.156 10 false *d 2.177,1.635 2.49,1.792 0.313,0.156 10 false *e
*a Retainer
*b Fuel Pipe
*c Nylon Tube
*d Fuel Tube Connector
*e O-Ring


Check for any dirt and foreign matter contamination in the fuel pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the fuel pipe and connector.

·

Do not use any tools to separate the fuel pipe and connector.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Check for any dirt and foreign matter on the fuel pipe seal surface. Clean if necessary.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tube.

·

If the fuel pipe and connector are stuck together, pinch the tube between your fingers and turn it carefully to free it. Then disconnect the fuel tube.




iii.

Check for foreign matter on the seal surface of the disconnected fuel pipe. Clean it if necessary.


iv.

To protect the disconnected fuel pipe and connector from damage and foreign matter, cover them with a plastic bag.



g.

Perform the following procedure when connecting a fuel tube connector (for quick type C).

i.

Check for foreign matter on the fuel pipe and around the connector before connecting it. Clean it if necessary.


ii.
A303816C07
1.958,1.531 2.365,1.531 false 1.958,1.281 2.365,1.281 false 2.781,1.271 3.188,1.271 false 1.781,1.448 2.094,1.604 0.313,0.156 10 false *a 1.823,1.198 2.135,1.354 0.313,0.156 10 false *b 3.24,1.208 3.427,1.365 0.188,0.156 10 false *b
*a Retainer
*b Claw
V100135

Push
V100136

Push in


Align the axis of the connector with the axis of the fuel pipe. Push the fuel pipe into the connector, and then push up on the retainer.

NOTICE:
·

Before connecting the tube connectors to the fuel pipes, check if there is any damage or foreign matter in the connectors.

·
A227055C15
0,0 0,0 false
V100135

Pull


After connecting the fuel pipe and the connector, check that the fuel pipe and connector are securely connected by trying to pull them apart.





h.

Perform the following procedure when disconnecting a fuel tube connector (for Quick Type D).

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A398462C01
2.188,0.938 2.458,0.49 2.458,0.49 2.656,0.49 true 1.542,1.76 1.698,1.76 1.698,1.76 2.031,1.979 true 2.844,2.417 3.094,2.417 true 2.823,1.875 3.073,1.875 true 1.896,2.927 2.052,2.927 2.052,2.927 2.344,3.219 true 2.75,3.75 2.938,3.323 2.938,3.323 3.063,3.323 true 1.521,3.646 1.01,3.292 1.01,3.292 0.75,3.292 true 2.073,4.146 2.073,4.396 true 1.938,4.156 1.938,4.323 1.938,4.323 2.073,4.323 true 1.365,1.667 1.583,1.833 0.219,0.167 10 false *a 2.688,0.396 2.906,0.552 0.219,0.156 10 false *b 0.583,3.198 0.771,3.354 0.188,0.156 10 false *c 2,4.427 2.198,4.583 0.198,0.156 10 false *d 3.094,1.781 3.302,1.948 0.208,0.167 10 false *e 3.115,2.323 3.323,2.49 0.208,0.167 10 false *e 1.708,2.833 1.927,3 0.219,0.167 10 false *a 3.104,3.24 3.323,3.396 0.219,0.156 10 false *b
*a Retainer
*b Fuel Pipe
*c Fuel Tube Connector
*d O-Ring
*e Claw
V100135

Push
V100136

Pull out
V100137

Pull off


Disengage the 2 claws of the retainer. Pull out the retainer and disconnect the fuel tube connector from the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has an O-ring that seals the pipe (fuel pipe).




iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



i.

Perform the following procedure when connecting a fuel tube connector (for Quick Type D).

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A398463C01
1.521,2.292 1.083,2.042 1.083,2.042 0.906,2.042 true 2.271,2.188 2.688,2.188 true 2.281,2.74 2.698,2.74 true 0.719,1.948 0.917,2.125 0.198,0.177 10 false *a 2.719,2.094 2.938,2.26 0.219,0.167 10 false *b 2.719,2.656 2.938,2.823 0.219,0.167 10 false *b
*a Retainer
*b Claw
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.


ii.

Connect the fuel lines and push in the retainer to engage the 2 claws. Check that the fuel pipe and fuel tube connector are securely connected by pulling on them.


iii.

Inspect for fuel leaks.



j.

Perform the following procedure when disconnecting a fuel tube connector (for Quick Type E).

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.

Check that there is no foreign matter around the fuel tube connector before disconnecting it. Clean it if necessary.


ii.
A403898C01
1.833,2.344 2.073,2.031 2.073,2.031 2.219,2.031 false 2.271,1.948 2.583,2.104 0.313,0.156 10 false *a
*a Retainer
V100135

Retainer Holding Position
V100136

Pull out


While holding the retainer at the positions shown in the illustration, pull up the retainer to detach the lock claws.

HINT:
A403900C01
1.677,0.698 1.833,0.698 1.833,0.698 2.042,0.99 false 1.833,0.365 1.979,0.365 1.979,0.365 2.323,0.875 false 1.667,0.271 1.979,0.427 0.313,0.156 10 false *a 1.51,0.615 1.823,0.771 0.313,0.156 10 false *b
*a Retainer
*b Protective Tape


If the lock claws of the retainer are difficult to detach, detach them using a screwdriver with its tip wrapped with protective tape.



iii.
A403899C01
1.167,0.354 1.313,0.354 1.313,0.354 1.625,0.646 false 1.896,1.948 2.104,1.573 2.104,1.573 2.25,1.573 false 1.979,3.188 2.073,2.938 2.073,2.938 2.219,2.938 false 1.354,3.333 1.604,3.333 1.604,3.333 1.604,3.594 false 2.125,3.885 2.281,4.302 2.281,4.302 2.396,4.302 false 0.833,4.177 0.833,3.917 true 1.875,4.26 1.875,4.063 false 1.479,3.594 1.479,3.333 false 1,0.26 1.313,0.417 0.313,0.156 10 false *a 1.198,3.24 1.51,3.396 0.313,0.156 10 false *b 1.802,4.292 2.115,4.448 0.313,0.156 10 false *c 0.75,4.208 1.063,4.365 0.313,0.156 10 false *d 2.448,4.208 2.76,4.365 0.313,0.156 10 false *e 2.302,1.49 2.615,1.646 0.313,0.156 10 false *a 2.271,2.854 2.583,3.01 0.313,0.156 10 false *a
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Nylon Tube
*e Fuel Pipe
V100135

Retainer Holding Position
V100136

Pull out
V100137

Pull off


Pull up the retainer while holding it at the positions shown in the illustration and pull off the fuel tube connector.


iv.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Do not bend, twist, pinch or kink the nylon tube.




v.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


vi.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



k.

Perform the following procedure when connecting a fuel tube connector (for Quick Type E).

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A393281C01
1.167,2.354 1.448,2.354 false 1,2.25 1.313,2.406 0.313,0.156 10 false *a
*a Retainer
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, push the fuel tube connector onto the fuel pipe, and then push in the retainer to secure the connection.

NOTICE:

Confirm that the retainer makes a "click" sound when pushed.


HINT:

If it is difficult to push the fuel tube connector onto the fuel pipe, apply a small amount of clean gasoline to the tip of the fuel pipe.



ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.


iii.

Inspect for fuel leaks.




FUEL SUCTION TUBE WITH PUMP AND GAUGE TUBE ASSEMBLY


a.

Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge tube assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is welded to the plate.

A487503C01
0.365,0.156 0.677,0.313 0.313,0.156 10 false *A 4.094,0.156 4.406,0.313 0.313,0.156 10 false *B
*A for Single Tank Type *B for Double Tank Type