Home › Engine / Hybrid System › 1GR-FE (FUEL) › FUEL SYSTEM
RM38G0E _51 Engine / Hybrid System _101386 1GR-FE FUEL _0470051 FUEL SYSTEM G

1GR-FE FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 23220A 1.CHECK FOR FUEL PUMP OPERATION AND FUEL LEAK

a.

Check the fuel pump operation.

NOTICE:

Do not start the engine.


Powertrain > Engine > Active Test
Tester Display
Control the Fuel Pump Duty Ratio (Brushless)
50004 372 39
i.

Check for pressure in the fuel inlet tube from the fuel line. Check that the sound of fuel flowing in the fuel tank can be heard.

If there is no sound, check the relay, fuel pump, ECM and wiring connector.



b.

Inspect for fuel leaks.

i.

Check that there are no fuel leaks after performing maintenance anywhere on the system.

If there are fuel leaks, repair or replace parts as necessary.



Hide 2.CHECK FUEL PRESSURE


b.

Discharge the fuel system pressure.

Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION


c.

Disconnect the cable from negative (-) battery terminal.

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY



d.

Remove the fuel pipe clamp.


e.
A487615

Disconnect the No. 1 fuel pipe sub-assembly from the fuel pipe.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


f.
A487608C01
0.438,2.271 0.573,2.271 0.573,2.271 0.74,2.594 false 1.333,4.01 1.573,4.01 false 0.802,0.625 1.042,0.625 false 0.438,0.906 0.583,0.906 0.583,0.906 0.677,1.115 false 1.323,1.052 1.438,1.219 1.438,1.219 1.594,1.219 false 3.26,1.344 3.26,1.104 3.26,1.104 3.188,0.958 false 1.927,2.406 2.26,2.406 false 1.313,0.448 1.604,0.448 false 1.5,4.344 1.729,4.344 false 2.302,2.323 2.615,2.479 0.313,0.156 10 false *1 0.25,2.177 0.49,2.385 0.24,0.208 10 false *a 1.146,3.927 1.354,4.135 0.208,0.208 10 false *b 1.635,1.125 1.948,1.281 0.313,0.156 10 false *c 3.156,1.375 3.344,1.594 0.188,0.219 10 false *d 1.635,0.365 1.948,0.521 0.313,0.156 10 false *e 1.344,4.271 1.521,4.479 0.177,0.208 10 false *f 0.26,0.823 0.427,1.031 0.167,0.208 10 false *b 0.625,0.542 0.813,0.75 0.188,0.208 10 false *b
*1 No. 1 Fuel Pipe Sub-assembly
*a SST (Hose)
*b SST (Hose Band)
*c SST (T Joint)
*d SST (Pressure Gauge)
*e SST (Hose Joint)
*f SST (Fuel Tube Connector)


Install SST (pressure gauge) as shown in the illustration.

SST
09268-45101  (09268-41250, 09268-41260, 09268-41280, 09268-41500, 09268-41700, 95336-08070)


g.

Wipe off any gasoline.


h.

Connect the cable to the negative (-) battery terminal.


i.

Operate the fuel pump.

NOTICE:

Do not start the engine.


Powertrain > Engine > Active Test
Tester Display
Activate the Circuit Relay (Brushless)
50004 372 40

j.

Measure the fuel pressure.

Standard fuel pressure:

321 to 327 kPa (3.3 to 3.3 kgf/cm2, 46.5 to 47.4 psi)


If the pressure is higher than the specification, replace the fuel pressure regulator assembly.

If the pressure is below the specification, check the fuel hoses and connections, fuel pump, fuel filter assembly and fuel pressure regulator assembly.


k.

Start the engine.


l.

Measure the fuel pressure.

Standard fuel pressure:

321 to 327 kPa (3.3 to 3.3 kgf/cm2, 46.5 to 47.4 psi)


If the pressure is not as specified, check the fuel pump, fuel pressure regulator assembly and fuel injector assemblies.


m.

Stop the engine.


n.

Check that the fuel pressure remains as specified for 5 minutes after the engine has stopped.

Standard fuel pressure:

147 kPa (1.5 kgf/cm2, 21 psi) or higher


If the pressure is not as specified, check the fuel pump, fuel pressure regulator assembly and fuel injector assembly.


o.

Disconnect the cable from the negative (-) battery terminal and carefully remove SST and the fuel tube connector to prevent gasoline from spraying.


p.

Connect the No. 1 fuel pipe sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION


q.

Install the fuel pipe clamp.


r.

Check that there are no fuel leaks after performing maintenance anywhere on the system.

If there are fuel leaks, repair or replace parts as necessary.