Use the following procedure to troubleshoot the parking support brake system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Measure the battery voltage with the ignition switch off.
11 to 14 V
If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.
| Proceed to |
|---|
| NEXT |
NEXT
Use the GTS to check if the CAN communication system is functioning normally.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output | A |
| CAN communication system DTCs are output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check the vehicle specification.
| Result | Proceed to |
|---|---|
| w/ Rear Crossing Vehicles Function | A |
| w/o Rear Crossing Vehicles Function and w/ Rear Pedestrians Function | B |
| w/o Rear Crossing Vehicles Function and w/o Rear Pedestrians Function | C |
A
B
C
Use the GTS to check if the blind spot monitor system is functioning normally.
| Result | Proceed to |
|---|---|
| DTCs are not output (w/ Rear Pedestrians Function) | A |
| DTCs are not output (w/o Rear Pedestrians Function) | B |
| DTCs are output | C |
A
B
C
Use the GTS to check if the panoramic view monitor system is functioning normally.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
A
B
Refer to Diagnostic Trouble Code Chart.
The clearance warning ECU assembly outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the parking support brake system are output, refer to Diagnostic Trouble Code Chart for the relevant systems.
| System | Proceed to |
|---|---|
| TOYOTA Parking Assist-sensor System | ( ) |
| Proceed to |
|---|
| NEXT |
NEXT
Refer to Vehicle Control History.
Check for vehicle control history and note any codes that are output.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Result | Proceed to |
|---|---|
| No vehicle control history is output (Problem symptom does not occur) | A |
| No vehicle control history is output (Problem symptom occurs) | B |
| X20C0 or X20C1 is output | C |
| Any vehicle control history other than X20C0 or X20C1 is output | D |
A
B
C
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>CALIBRATION
D
Refer to Symptom Simulation.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| Proceed to |
|---|
| NEXT |
NEXT
Refer to Problem Symptoms Table.
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
A
B
Operation Check
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>OPERATION CHECK
Terminals of ECU
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>TERMINALS OF ECU
Data List / Active Test
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT