Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P023A12  Charge Air Cooler Coolant Pump Control Circuit Short to Battery  


DESCRIPTION

The intercooler cooling system is a water cooling system that is independent from the engine cooling system. It uses a dedicated radiator and electric water pump assembly to cool the intercooler and turbocharger. The electric water pump assembly uses the duty cycle signals sent from the ECM to provide stepless, optimal control of the electric water pump assembly speed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P023A12 Charge Air Cooler Coolant Pump Control Circuit Short to Battery The operation duty ratio signal (IWPO) of the electric water pump assembly is a certain value or more when the electric water pump assembly operation signal is being output (1 trip detection logic).
·

Short in electric water pump assembly circuit

·

Electric water pump assembly

·

ECM


- SAE: P023C

Related Data List
DTC No. Data List
P023A12
·

Intercooler Water Pump Speed

·

Intercooler Water Pump



MONITOR DESCRIPTION

The ECM outputs an operation duty signal (IWPO) to steplessly control the speed of the electric water pump assembly. The ECM outputs an operation duty signal (IWPO) to the electric water pump assembly and monitors the actual duty signal (IWPO) being output. When the actual operation duty signal (IWPO) exceeds a certain value when outputting an operation duty signal (IWPO) to the electric water pump assembly, the ECM detects a malfunction and stores a DTC.

CONFIRMATION DRIVING PATTERN

1.
A330723E40
3.042,1.854 2.635,1.344 2.635,1.344 2.438,1.344 false 0.25,0.292 1.354,0.542 1.104,0.25 10 false Vehicle Speed 0.76,0.677 1.375,0.875 0.615,0.198 10 false 50 km/h 0.927,2.042 1.542,2.24 0.615,0.198 10 false Idling 0.417,2.385 1.333,2.771 0.917,0.385 10 false Ignition switch ON 5.625,3.375 5.99,3.625 0.365,0.25 10 false [C] 1.427,1.26 2.729,1.563 1.302,0.302 10 false Fully depressed 2.198,1.885 2.656,2.083 0.458,0.198 10 false [A] 3.313,1.219 3.792,1.417 0.479,0.198 10 false [B]

2.

Connect the GTS to the DLC3.

3.

Turn the ignition switch to ON.

4.

Turn the GTS on.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Turn the ignition switch off and wait for at least 30 seconds.

7.

Turn the ignition switch to ON.

8.

Turn the GTS on.

9.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

10.

Accelerate to 50 km/h (31 mph) or more with the accelerator pedal fully depressed [B].

NOTICE:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P023A12.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [B] through [C] again.




WIRING DIAGRAM

A408338E02
0.729,4.104 1.438,4.375 0.708,0.271 10 false Battery 0.51,3.094 1.51,3.5 1,0.406 10 false SUB R/B-NO. 1 0.49,2.729 1.604,3 1.115,0.271 10 false EFI MAIN NO. 1 1.531,3.01 2.646,3.281 1.115,0.271 10 false EFI NO. 2 5.677,2.865 6.26,3.073 0.583,0.208 10 false MREL 2.052,3.208 3.167,3.479 1.115,0.271 10 false EFI MAIN NO. 1 0.563,0.583 1.677,0.854 1.115,0.271 10 false EFI MAIN NO. 3 1.958,1 3.073,1.271 1.115,0.271 10 false EFI MAIN NO. 3 3.125,1.365 4.24,1.635 1.115,0.271 10 false EFI-B NO. 4 5.729,0.26 6.26,0.448 0.531,0.188 10 false IWPO 3.198,0.552 4,0.792 0.802,0.24 10 false EFI NO. 4 5.677,1.531 6.208,1.719 0.531,0.188 10 false IWPI 3.917,2.156 5.219,2.563 1.302,0.406 10 false Electric Water Pump Assembly 4.594,0.385 5,0.667 0.406,0.281 10 false SWP 4.167,0.375 4.573,0.656 0.406,0.281 10 false +B 4.156,1.646 4.604,1.885 0.448,0.24 10 false PGND 4.604,1.646 5.01,1.927 0.406,0.281 10 false NWP 6.125,3.531 6.708,3.74 0.583,0.208 10 false B1 6.146,3.708 6.729,3.917 0.583,0.208 10 false ECM 5.458,2.719 5.604,2.906 0.146,0.188 10 false 3 5.438,1.542 5.625,1.74 0.188,0.198 10 false 38 5.438,0.271 5.625,0.469 0.188,0.198 10 false 37 5.021,1.531 5.167,1.719 0.146,0.188 10 false 2 3.979,1.51 4.125,1.698 0.146,0.188 10 false 1 5.042,0.26 5.188,0.448 0.146,0.188 10 false 3 3.948,0.25 4.094,0.438 0.146,0.188 10 false 4 2.875,0.26 3.021,0.448 0.146,0.188 10 false 5 2.875,2.438 3.021,2.625 0.146,0.188 10 false 5 2.875,0.531 3.021,0.719 0.146,0.188 10 false 2 2.875,2.729 3.021,2.917 0.146,0.188 10 false 2 2.031,0.26 2.177,0.448 0.146,0.188 10 false 3 2.052,2.438 2.198,2.625 0.146,0.188 10 false 3 2.042,0.552 2.188,0.74 0.146,0.188 10 false 1 2.052,2.719 2.198,2.906 0.146,0.188 10 false 1 3.927,1.979 4.51,2.188 0.583,0.208 10 false B29

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ELECTRIC WATER PUMP ASSEMBLY)
a.

Disconnect the electric water pump assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B29)Location & Routing

Click Connector(B29)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Electric Water Pump Assembly

B29-3 (SWP) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT ECM (SWP TERMINAL)

NG

3.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - ECM)
2.INSPECT ECM (SWP TERMINAL)
a.

Disconnect the electric water pump assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Powertrain > Engine > Active Test
Tester Display
Control the Intercooler Water Pump
50004 372 9
Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B29)Location & Routing

Click Connector(B29)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Electric Water Pump Assembly

B29-3 (SWP) - Body ground Active Test OFF → ON Active Test OFF: Resistance stabilized → ON: Resistance changes*


HINT:

*: The transistor inside the ECM performs duty control according to the Active Test being operated. The resistance of the SWP terminal changes while the Active Test is on due to duty control. If the resistance is stable while the Active Test is off and changes while the Active Test is on, the transistor is working correctly. If the transistor does not operate when the Active Test is on, there may be a malfunction in the ECM.



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRIC WATER PUMP ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - ECM)
a.

Disconnect the electric water pump assembly connector.


b.

Disconnect the ECM connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR