Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › ECM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0467365 ECM A

V35A-FTS ENGINE CONTROL  ECM  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A486357N01
2.688,1.083 3.021,1.083 false 5.281,1.385 5.5,1.656 5.5,1.656 5.708,1.656 false 3.313,1.646 3.771,1.646 false 1.26,0.948 1.625,0.677 1.625,0.677 1.813,0.677 false 6.427,0.26 6.885,0.26 false 6.438,0.646 6.844,0.646 false 2.448,0.938 2.729,1.292 0.281,0.354 18 false 4 3.125,1.5 3.406,1.854 0.281,0.354 18 false 6 5.813,1.521 6.094,1.875 0.281,0.354 18 false 5 4.354,1.448 4.813,1.646 0.458,0.198 10 false x 2 5.771,1.188 6.229,1.385 0.458,0.198 10 false x 2 1.927,0.542 2.208,0.896 0.281,0.354 18 false 3 4.188,0.958 4.646,1.156 0.458,0.198 10 false x 2 6.219,0.125 6.5,0.479 0.281,0.354 18 false 1 6.229,0.51 6.51,0.865 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
3 AIR WITH ELEMENT CLEANER ASSEMBLY LH 17800 - - -
4 ECM 89661 (Click here) - -
5 NO. 2 ECM BRACKET 89668 - - -
6 NO. 1 ECM BRACKET 89667E - - -

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ECM removal/installation are shown below.

CAUTION / NOTICE / HINT

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
ECM The Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output (Click here)

Heavy Knock History

-

Save history

-

Write history



- (Click here)
Perform switch specification information Vehicle control history (RoB) [X263E] is stored (Click here)
Update ECU security key Vehicle control history (RoB) [XF01B] is stored (Click here)
Perform code registration Engine start See Service Bulletin for the registration method.
Disconnect cable from negative battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function when Necessary Procedure not Performed Necessary Procedure Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system


·

Learning completes when vehicle is operated normally

Effect/Inoperative Function when Necessary Procedure not Performed Necessary Procedure Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 17800 3.REMOVE AIR WITH ELEMENT CLEANER ASSEMBLY LH

Hide 89661 4.REMOVE ECM

a.
A486437N01
0.448,0.052 0.604,0.333 0.156,0.281 18 true ii 4.646,0.615 4.844,0.906 0.198,0.292 18 true iii 2.781,0.573 2.927,0.854 0.146,0.281 18 true i 4,0.031 4.229,0.323 0.229,0.292 18 true iv

i.

Detach the 2 wire connector clamps.


ii.

Push in the locks on the 3 levers, raise the 3levers, and disconnect the 3 ECM connectors.

NOTICE:

After disconnecting the ECM connectors, make sure that dirt, water and other foreign matter does not contact the connecting parts of the ECM connectors.



iii.

Detach the 3 wire harness clamps.


iv.

Remove the 3 bolts and ECM.

NOTICE:

If the ECM has been struck or dropped, replace it.




Hide 89668 5.REMOVE NO. 2 ECM BRACKET

A486359

Hide 89667E 6.REMOVE NO. 1 ECM BRACKET

A486360