Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P071531  Input/Turbine Speed Sensor "A" No Signal  


DESCRIPTION

The transmission revolution sensor (NT) detects the input shaft rotation speed and sends it to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P071531 Input/Turbine Speed Sensor "A" No Signal No transmission revolution sensor (NT) signal to the main CPU while running
·

Open or short in transmission revolution sensor (NT) signal circuit

·

TCM

·

ECM


Comes on SAE: P0717

MONITOR DESCRIPTION

The NT signal is input from the transmission revolution sensor (NT) to the ECM and transmission control ECU while the vehicle is driven. When the NT signal is not input to the ECM only while the vehicle is driven, a malfunction in an NT signal circuit is judged, the MIL is illuminated and a DTC is stored.

MONITOR STRATEGY

Required Sensors/Components Transmission revolution sensor (NT)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Drive the vehicle at approximately 30 km/h (18.65 mph) for 30 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P071531.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A480736E01
5.188,1.458 5.646,1.656 0.458,0.198 10 false NTP 5.698,3.229 6.156,3.427 0.458,0.198 10 false ECM 1.167,3.208 1.625,3.406 0.458,0.198 10 false TCM 1.75,1.594 2.208,1.792 0.458,0.198 10 false NTOE 1.167,3.021 1.625,3.219 0.458,0.198 10 false C36 5.688,3.052 6.146,3.25 0.458,0.198 10 false C38 4.813,1.469 5.271,1.667 0.458,0.198 10 false 30 2.281,1.469 2.74,1.667 0.458,0.198 10 false 51

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P071531)
a.

Perform the Health Check using the GTS.


b.

Read the DTCs.

Result:
Result Proceed to
P071531 is output A
P071531 and other DTCs are output B


HINT:

If any DTCs other than P071531 are output, troubleshoot those DTCs first.




A

2.CHECK HARNESS AND CONNECTOR (TCM - ECM)

B

GO TO DTC CHART

2.CHECK HARNESS AND CONNECTOR (TCM - ECM)
a.

Disconnect the TCM connector.


b.

Disconnect the ECM connector.



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P071531)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P071531)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P071531 is output B




A

B

5.REPLACE TCM
5.REPLACE TCM

NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P071531)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P071531)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P071531 is output B




A

END

B