Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P2AB715  Wastegate Position Sensor "A" Circuit Short to Battery or Open  P2ABA15  Wastegate Position Sensor "B" Circuit Short to Battery or Open  


DESCRIPTION

Refer to DTC P2AB711.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P2AB711

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P2AB715 Wastegate Position Sensor "A" Circuit Short to Battery or Open The ball valve position sensor (bank 1) output voltage is higher than 4.8 V for 3 seconds or more (1 trip detection logic).
·

Open or short in waste gate position sensor (waste gate valve actuator assembly (bank 1)) circuit

·

Waste gate position sensor (waste gate valve actuator assembly (bank 1))

·

ECM


- SAE: P2AB9
P2ABA15 Wastegate Position Sensor "B" Circuit Short to Battery or Open The ball valve position sensor (bank 2) output voltage is higher than 4.8 V for 3 seconds or more (1 trip detection logic).
·

Open or short in waste gate position sensor (waste gate valve actuator assembly (bank 2)) circuit

·

Waste gate position sensor (waste gate valve actuator assembly (bank 2))

·

ECM


- SAE: P2ABC

MONITOR DESCRIPTION

If the output voltage transmitted by the waste gate valve position sensor remains high, the ECM interprets this as a malfunction in the sensor circuit, stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

6.

Turn the ignition switch off and wait for at least 30 seconds.

7.

Turn the ignition switch to ON.

8.

Turn the GTS on.

9.

Start the engine.

10.

Idle the engine for 5 seconds or more.

11.

Enter the following menus: Powertrain / Engine / Trouble Codes.

12.

Read the DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P2AB715 or P2ABA15.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

DTC Suspected Area
P2AB715 Bank 1
P2ABA15 Bank 2



PROCEDURE

1.CHECK HARNESS AND CONNECTOR
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the waste gate valve actuator assembly (turbocharger sub-assembly) connector.


b.

Turn the ignition switch to ON.



d.

Turn the ignition switch off and wait for at least 30 seconds.



Result:
Proceed to
OK
NG


HINT:

Perform "Inspection After Repair" after replacing the turbocharger sub-assembly.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



OK

REPLACE WASTE GATE VALVE ACTUATOR ASSEMBLY (TURBOCHARGER SUB-ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (WASTE GATE VALVE ACTUATOR ASSEMBLY (TURBOCHARGER SUB-ASSEMBLY) - ECM)
2.CHECK HARNESS AND CONNECTOR (WASTE GATE VALVE ACTUATOR ASSEMBLY (TURBOCHARGER SUB-ASSEMBLY) - ECM)
a.

Disconnect the waste gate valve actuator assembly (turbocharger sub-assembly) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C45,C37,C46)Location & Routing

Click Connector(C45)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>No. 1 Turbocharger Sub-Assembly

Click Connector(C37)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C46)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>No. 2 Turbocharger Sub-Assembly

C45-3 (AWGR) - C37-99 (WGA) Always Below 1 Ω
C45-4 (EWGR) - C37-106 (EWGA) Always Below 1 Ω
C46-3 (AWGL) - C37-98 (WGA2) Always Below 1 Ω
C46-4 (EWGL) - C37-104 (EWG2) Always Below 1 Ω
C45-4 (EWGR) or C37-106 (EWGA) - Body ground and other terminals Always 10 kΩ or higher
C46-4 (EWGL) or C37-104 (EWG2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR