Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM D

V35A-FTS ENGINE CONTROL  SFI SYSTEM  VEHICLE CONTROL HISTORY (RoB)  


DESCRIPTION (SFI SYSTEM)


·

Vehicle Control History is a function that captures and stores ECU data when triggered by specific vehicle behavior.

·

If the customer states that the engine stalls or will not start, it may be possible to diagnose the cause of the malfunction by checking the vehicle history information and freeze frame data.

·

The number of possible stored Freeze Frame Data sets, whether multi Freeze Frame Data is available, the number of freeze frame points, Freeze Frame Data items, the ECU internal range, etc., is different depending on the stored group.

·

The stored data items for Vehicle Control History Freeze Frame Data are different depending on the stored group. When the value of a data item does not change across all points, only the value of the detection point will be displayed. The content of the Freeze Frame Data is almost the same as that of the Data List.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST



PRECAUTIONS (SFI SYSTEM)


·

As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save Vehicle Control History before performing any inspections.

·

As Vehicle Control History may be stored when performing an Active Test, learning, etc., make sure to clear the Vehicle Control History before returning the vehicle to the customer.



CHECK VEHICLE CONTROL HISTORY (SFI SYSTEM)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55
HINT:

It is also possible to display Vehicle Control History during the Health Check, if "Store All Data" is selected.


Vehicle Control History Item
Code Item Trigger Description Stored Group Reference Inspection Procedure Link
X0800 Engine Stall
Detection Condition (Engine Stall)
·

Prerequisite Conditions: The engine is running (after engine is judged to be difficult to start)

·

Detection Conditions: The engine speed decreases to 200 rpm or less, or stops

·

Duration: 0.5 seconds or more


08 Flowchart [Engine Stalls] step 3 (Click here)
The engine stalled due to factors other than the operation of the ignition switch
X0803 Engine Stall (Compression Leakage) It is judged that the engine is stalled due to compression leakage 08 Flowchart [Engine Stalls] step 3 (Click here)
X0810 Engine Difficult to Start (Engine Starting Time Long)
Detection Condition (Engine Starting Time Long)
·

Prerequisite Conditions: STA signal is ON

·

Detection Conditions: The engine speed is less than 500 rpm for a long period of time (the starting time is long or the engine does not start)

·

Duration: Refer to Engine Difficult to Start Duration Judgment Region illustration


09 Flowchart [Engine Difficult to Start] step 3 (Click here)
The engine speed decreases or the engine stalls immediately after starting
X0811 Engine Difficult to Start (Engine Stall Immediately After Starting)
Detection Condition (Engine Stall Immediately After Starting)
·

Prerequisite Conditions: Within 2 seconds after the engine has started (engine speed is 500 rpm or more) and the engine coolant temperature is -15°C (5°F) or more

·

Detection Conditions: The engine speed decreases to 200 rpm or less (immediately after starting, the engine speed decreases or the engine stalls)

·

Duration: -


09 Flowchart [Engine Difficult to Start] step 3 (Click here)
The engine speed decreases or the engine stalls immediately after starting
X0812 Engine Difficult to Start (Immobiliser) Engine difficult to start due to immobiliser 09 Flowchart [Engine Difficult to Start] step 3 (Click here)
X0821 Rough Idle #1
Detection Condition (Rough Idle)
·

Prerequisite Conditions: The engine is idling with the vehicle stopped and the accelerator pedal is fully released

·

Detection Conditions: It is judged that combustion is unstable due to the instantaneous change in engine speed for each cylinder

·

Duration: Depending on the combustion status, between 2 and 10 seconds


03 Flowchart [Rough Idling] step 3 (Click here)
Idling is rough due to unstable combustion in the No. 1 cylinder
X0822 Rough Idle #2 Idling is rough due to unstable combustion in the No. 2 cylinder 03 Flowchart [Rough Idling] step 3 (Click here)
X0823 Rough Idle #3 Idling is rough due to unstable combustion in the No. 3 cylinder 03 Flowchart [Rough Idling] step 3 (Click here)
X0824 Rough Idle #4 Idling is rough due to unstable combustion in the No. 4 cylinder 03 Flowchart [Rough Idling] step 3 (Click here)
X0825 Rough Idle #5 Idling is rough due to unstable combustion in the No. 5 cylinder 03 Flowchart [Rough Idling] step 3 (Click here)
X0826 Rough Idle #6 Idling is rough due to unstable combustion in the No. 6 cylinder 03 Flowchart [Rough Idling] step 3 (Click here)
X082A Rough Idle (Plural Cylinders) Idling is rough due to multiple cylinders
As more than one cylinder is affected, the fuel system, etc. is suspected
03 Flowchart [Rough Idling] step 3 (Click here)
X082D Rough Idle (Compression Leakage) Idling is judged to be rough due to compression leakage 03 Flowchart [Rough Idling] step 3 (Click here)
X082E Rough Idle (Low Frequency) Slight rough idle symptoms are detected 3 times in 10 trips
HINT:

As the rough idle symptoms are slight, if rough idle codes other than rough idle (low frequency) code X082E are stored, this code will not be stored.


03 Flowchart [Rough Idling] step 3 (Click here)
X0844 Engine Lack of Power
Detection Condition (Engine Lack of Power)
·

Prerequisite Conditions: All of the following conditions are met

-

The accelerator opening angle 80% or more.

-

The engine speed is 1800 rpm or more.

-

The engine coolant temperature is 70°C (158°F) or higher

-

The intake air temperature is 60°C (140°F) or less.

-

The atmospheric pressure is 95 kPa(abs) [13.78 psi(abs)] or higher.

-

The STP signal is off.

-

The STA signal is off.

-

Shift lever is not in P or N.


·

Detects a condition where the output torque is insufficient approximately 40% or more relative to the requested torque (divided value of the output torque is approximately 0.6 less than the requested torque)

·

Duration: 3 seconds or more


04 Flowchart [Lack of Power] step 3 (Click here)
X0850 Engine Oil Pressure Low The engine oil pressure is low 05 - -
X0851 Engine Coolant Temperature High The engine coolant temperature is high (overheating) 05 - -
X0852 Engine RPM High The engine speed is high (over revving) 05 - -
X0854 Engine Coolant Temperature High (Low Voltage) The engine coolant temperature is high (overheating) due to a low engine water pump assembly voltage causing the engine water pump assembly to stop
HINT:

Only for vehicles equipped with an electric water pump (for engine).


05 - -
X263E Suspension Specification Information Learning Incomplete Suspension specification information is unlearned - Perform Switch Specification Information (Click here)
XF01B ECU Security Key Not Registered ECU security key has not been updated - - (Click here)

Engine Difficult to Start Duration Judgment Region (Engine Starting Time Long) (X0810)
A220316E34
0.314,1.64 1.192,1.824 0.878,0.184 10 Starting Time 1.276,0.37 1.960,0.554 0.684,0.184 10 (Seconds) 3.844,1.136 5.000,1.486 1.156,0.350 10 Region Indicating Malfunction 6.384,2.761 6.665,2.959 0.281,0.198 10 (°C) 1.43,2.26 1.553,2.437 0.123,0.177 10 2 1.892,2.78 2.132,2.936 0.239,0.156 10 -30 3.517,2.78 3.715,2.950 0.198,0.170 10 20 5.198,2.78 5.410,2.964 0.211,0.184 10 80 3.518,3.178 5.368,3.362 1.850,0.184 10 Engine Coolant Temperature

Stored Data
Stored Group Number of Records Number of Freeze Frame Points Multi Freeze Frame Data Sampling Period Note
03 1 code
HINT:
·

If the detection conditions for a code that is not currently stored are met, the code will be stored.

·

If the detection conditions for a code that is currently stored are met again in the same trip, the code will not be overwritten.

·

If the detection conditions for a code that is currently stored are met again in a different trip, the code will be overwritten.

·

If rough idle codes other than Rough Idle (Low Frequency) code X082E are stored, data for code X082E will not be overwritten.



7 points (1 point at detection + 6 points before detection)
HINT:

When the value of a data item does not change across all points, only the value at the detection point will be displayed.


0.5 seconds The data can be cleared by using the GTS or by disconnecting the cable from the negative (-) battery terminal.
04 1 code
HINT:
·

If the detection conditions for a code that is not currently stored are met, the code will be stored.

·

If the detection conditions for a code that is currently stored are met again in the same trip, the code will not be overwritten.

·

If the detection conditions for a code that is currently stored are met again in a different trip, the code will be overwritten.



7 points (1 point at detection + 6 points before detection)
HINT:

When the value of a data item does not change across all points, only the value at the detection point will be displayed.


0.5 seconds The data can be cleared by using the GTS or by disconnecting the cable from the negative (-) battery terminal.
05 2 codes
HINT:
·

If the detection conditions for a code that is not currently stored are met, the code will be stored.

·

If the detection conditions for a code that is currently stored are met again in the same trip, the code will not be overwritten.

·

If the detection conditions for a code that is currently stored are met again in a different trip, the code will be overwritten.



1 point (multi freeze frame data not available) -
·

The data can be cleared by using the GTS.

·

The data cannot be cleared by disconnecting the cable from the negative (-) battery terminal.


08 1 codes
HINT:
·

If the detection conditions for a code that is not currently stored are met, the code will be stored.

·

If the detection conditions for a code that is currently stored are met again in the same trip, the code will not be overwritten.

·

If the detection conditions for a code that is currently stored are met again in a different trip, the code will be overwritten.



12 points (1 point at detection + 8 points before detection + 3 points after detection)
HINT:

When the value of a data item does not change across all points, only the value at the detection point will be displayed.


0.5 seconds
·

The data can be cleared by using the GTS.

·

The data cannot be cleared by disconnecting the cable from the negative (-) battery terminal.


09 1 code
HINT:
·

If the detection conditions for a code that is not currently stored are met, the code will be stored.

·

If the detection conditions for a code that is currently stored are met again in the same trip, the code will not be overwritten.

·

If the detection conditions for a code that is currently stored are met again in a different trip, the code will be overwritten.



7 points (1 point at detection + 3 points before detection + 3 points after detection)
HINT:

When the value of a data item does not change across all points, only the value at the detection point will be displayed.


0.5 seconds The data can be cleared by using the GTS or by disconnecting the cable from the negative (-) battery terminal.

HINT:
·

Multi Freeze Frame Data makes it possible to display the engine condition (ECU data) both before and after the trigger detection point.

·

The number of available points differs depending on the stored group.

·

When the value of a data item does not change across all points, only the value at the detection point will be displayed.


A405050E02
2.948,1.552 2.844,1.552 2.844,1.552 2.844,1.385 false 0.156,0.083 2.917,0.323 2.76,0.24 12 false Stored Group 03, 04 1.854,0.635 3.458,0.906 1.604,0.271 10 false Point Before Detection 1.667,2.344 3.802,2.656 2.135,0.313 10 false Recording Time Before Detection 1.094,1.927 3.063,2.188 1.969,0.26 10 false Sampling Cycle (0.5 seconds) 3.542,0.104 5.135,0.396 1.594,0.292 10 false Trigger Detection Point 2.969,1.458 4.177,1.948 1.208,0.49 10 false Freeze Frame Data which can be read

A414224E01
5.406,1.688 5.208,1.615 5.208,1.615 5.208,1.479 false 0.302,0.156 1.677,0.354 1.375,0.198 12 false Stored Group 08 4.156,0.135 5.677,0.323 1.521,0.188 10 false Trigger Detection Point 5.604,0.458 7,0.656 1.396,0.198 10 false Point After Detection 1.885,0.458 3.479,0.688 1.594,0.229 10 false Point Before Detection 2.979,1.958 4.885,2.229 1.906,0.271 10 false Sampling Cycle (0.5 seconds) 5.448,1.615 6.875,2.01 1.427,0.396 10 false Freeze Frame Data which can be read 1.542,2.417 3.667,2.656 2.125,0.24 10 false Recording Time Before Detection 5.167,2.448 7.135,2.677 1.969,0.229 10 false Recording Time After Detection

A412793E01
5.063,1.625 4.927,1.625 4.927,1.625 4.833,1.458 false 3.302,0.177 5.073,0.396 1.771,0.219 10 false Trigger Detection Point 1.573,0.552 3.281,0.813 1.708,0.26 10 false Point Before Detection 4.833,0.542 6.594,0.75 1.76,0.208 10 false Point After Detection 2.031,1.948 4.115,2.198 2.083,0.25 10 false Sampling Cycle (0.5 seconds) 0.198,0.146 1.917,0.417 1.719,0.271 12 false Stored Group 09 5.135,1.563 6.375,2.104 1.24,0.542 10 false Freeze Frame Data which can be read 1.406,2.427 3.802,2.646 2.396,0.219 10 false Recording Time Before Detection 4.458,2.427 6.781,2.656 2.323,0.229 10 false Recording Time After Detection

Only 1 measurement point can be displayed for stored group 05 Freeze Frame Data.




CLEAR VEHICLE CONTROL HISTORY (SFI SYSTEM)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB) (Clear).

NOTICE:

By performing this procedure, all stored Vehicle Control History items will be cleared.




VEHICLE CONTROL HISTORY FREEZE FRAME DATA (SFI SYSTEM)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55

e.

Select a vehicle control history item to access the applicable freeze frame data.


f.

Check the freeze frame Data recorded with the Vehicle Control History.

Vehicle Control History Data
A485829

A485830

A485831



CHECK VEHICLE CONTROL HISTORY (AUTOMATIC TRANSMISSION SYSTEM)


HINT:
·

The vehicle control history (automatic transmission system) stores the history of system protection operations.

·

The number of occurrences is stored for each item.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55
Vehicle Control History Item
Code Tester Display Measurement Item Diagnostic Note
X090A Limited Slip Differential Speed Higher than Expected History of high differential control operation while driving
·

Shift operation is prohibited to protect the differential when driving on a road with different friction between the left and right drive wheels and it is predicted that a large rotational difference will occur due to slip at one of the wheels.

·

It can be understood that one of the wheels slipped.


X090B Lock Up On (High A/T Oil Temperature) History of lock-up control operation due to the A/T fluid rising to a high temperature Switches to a shift line that restricts the engine speed until the A/T fluid temperature drops, in order to protect the A/T.



CLEAR VEHICLE CONTROL HISTORY (AUTOMATIC TRANSMISSION SYSTEM)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB) (Clear).

NOTICE:

By performing this procedure, all stored Vehicle Control History items will be cleared.




VEHICLE CONTROL HISTORY FREEZE FRAME DATA (AUTOMATIC TRANSMISSION SYSTEM)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55

e.

Select a vehicle control history item to access the applicable freeze frame data.


f.

Check the freeze frame Data recorded with the Vehicle Control History.

Vehicle Control History Data
Tester Display Description
Acceleration Sensor Correct Value Acceleration sensor calibration value
Throttle Position for Shift Point Control Throttle position for shift point control
Stop Light SW Brake pedal operation availability
Shift Range Signal Shift range
Turbine Rotation Speed Input shaft speed
Speed (SP2) ECT vehicle speed
A/T Oil Temperature No.1 ATF temperature sensor value
Output Axis Speed Output shaft speed
Limited Slip Differential Speed Higher than Expected Count Occurrence count of Limited Slip Differential Speed Higher than Expected
Lock Up On Count (High A/T Oil Temperature) Occurrence count of Lock Up On (High A/T Oil Temperature)



VEHICLE CONTROL HISTORY (AIRBAG SYSTEM)


HINT:

A part of the control history can be confirmed using the vehicle control history.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>VEHICLE CONTROL HISTORY