Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P042000  Catalyst System Efficiency Below Threshold Bank 1  P043000  Catalyst System Efficiency Below Threshold Bank 2  


MONITOR DESCRIPTION

The ECM uses air fuel ratio sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.

The first sensor, the air fuel ratio sensor (sensor 1), sends pre-catalyst information to the ECM. The second sensor, the air fuel ratio sensor (sensor 2), sends post-catalyst information to the ECM.

In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the output current of the air fuel ratio sensor (sensor 2) while performing active air fuel ratio control.

The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 30 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the cycle of the waveform for the air fuel ratio sensor (sensor 2) is long, the oxygen storage capacity is great. There is a direct correlation between the air fuel ratio sensor (sensor 2) and the oxygen storage capacity of the three-way catalytic converter.

The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, the ECM will illuminate the MIL and store a DTC.

This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P042000 Catalyst System Efficiency Below Threshold Bank 1 The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip detection logic).
·

Gas leak from exhaust system

·

Air fuel ratio sensor (bank 1 sensor 1)

·

Air fuel ratio sensor (bank 1 sensor 2)

·

Converter assembly RH (TWC: Front and rear catalyst)


Comes on SAE: P0420
P043000 Catalyst System Efficiency Below Threshold Bank 2 The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip detection logic).
·

Gas leak from exhaust system

·

Air fuel ratio sensor (bank 2 sensor 1)

·

Air fuel ratio sensor (bank 2 sensor 2)

·

Converter assembly LH (TWC: Front and rear catalyst)


Comes on SAE: P0430

CATALYST LOCATION

A485545C02
0.385,2.365 0.625,2.365 0.625,2.365 0.813,1.813 false 0.76,4.177 1,4.177 1,4.177 1.188,3.625 false 0.865,1.156 1.198,0.75 1.198,0.75 1.406,0.75 false 1.188,3.01 1.26,2.74 1.26,2.74 1.469,2.74 false 1.427,2.229 1.635,2.531 1.635,2.531 1.844,2.531 false 1.75,3.313 1.833,3.042 1.833,3.042 2.042,3.042 false 5.969,1.458 6.417,0.469 6.417,0.469 6.625,0.469 false 4,2.26 4.719,3.406 4.719,3.406 4.927,3.406 false 2.01,2.094 2.458,1.104 2.458,1.104 2.667,1.104 false 0.219,2.302 0.531,2.458 0.313,0.156 10 false *1 0.542,4.135 0.854,4.292 0.313,0.156 10 false *2 1.479,0.688 1.792,0.844 0.313,0.156 10 false *3 1.542,2.688 1.854,2.844 0.313,0.156 10 false *4 1.885,2.479 2.198,2.635 0.313,0.156 10 false *5 2.083,2.979 2.396,3.135 0.313,0.156 10 false *6 2.719,1.042 3.031,1.198 0.313,0.156 10 false *7 5,3.344 5.313,3.5 0.313,0.156 10 false *8 6.667,0.417 6.979,0.573 0.313,0.156 10 false *9
*1 Converter Assembly RH (TWC: Front and Rear Catalyst) *2 Converter Assembly LH (TWC: Front and Rear Catalyst)
*3 Air Fuel Ratio Sensor (Bank 1 Sensor 1) *4 Air Fuel Ratio Sensor (Bank 2 Sensor 1)
*5 Air Fuel Ratio Sensor (Bank 1 Sensor 2) *6 Air Fuel Ratio Sensor (Bank 2 Sensor 2)
*7 Front Exhaust Pipe Assembly *8 Center Exhaust Pipe Assembly
*9 Exhaust Tailpipe Assembly - -


MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor (sensor 1)
Air fuel ratio sensor (sensor 2)
Required Sensors/Components (Related) Intake air temperature (mass air flow meter sub-assembly)
Mass air flow meter sub-assembly
Crankshaft position sensor
Engine coolant temperature sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Response rate during fuel cut from rich condition Completed
Battery voltage 11 V or higher
Intake air temperature (mass air flow meter sub-assembly) -10°C (14°F) or higher
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa(abs) [11 psi(abs)] or higher
Idling Off
Engine speed Less than 3200 rpm
Sub feedback control Executing
Air fuel ratio sensor (sensor 1) status Activated
Fuel system status Closed loop
Engine load 10% or higher, and less than 140%
All of the following conditions are met 1, 2 and 3
1. Mass air flow 5 gm/sec or more, and less than 60 gm/sec
2. Front catalyst temperature (estimated) 540°C (1004°F) or higher, and less than 800°C (1472°F)
3. Rear catalyst temperature (estimated) 400°C (752°F) or higher, and less than 700°C (1292°F)

TYPICAL MALFUNCTION THRESHOLDS

Oxygen Storage Capacity (OSC) of catalyst (Normalized) Less than 1

CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.


A414842E05
1.323,0.865 1.781,0.375 1.781,0.375 2.01,0.375 false 2.063,0.292 5.427,0.49 3.365,0.198 10 false Between 75 to 100 km/h 0.698,1.135 4.063,1.333 3.365,0.198 10 false 60 km/h 0.896,2.219 4.26,2.417 3.365,0.198 10 false Idling 0.156,2.427 3.521,2.625 3.365,0.198 10 false Ignition Switch off 1.656,2.094 5.021,2.292 3.365,0.198 10 false [A] 2.573,1.01 5.938,1.208 3.365,0.198 10 false [B]* 3.479,2.104 6.844,2.302 3.365,0.198 10 false [D] 4.365,1.01 4.823,1.229 0.458,0.219 10 false [E]* 6.135,0.625 6.531,0.854 0.396,0.229 10 false [G]* 3.344,2.74 3.948,3.156 0.604,0.417 10 false Warming up 4.125,2.729 4.854,3.188 0.729,0.458 10 false 10 minutes or more 3.146,3.146 3.469,3.417 0.323,0.271 10 false [C] 1.49,2.729 2.094,3.146 0.604,0.417 10 false Warming up 2.323,2.74 3.052,3.198 0.729,0.458 10 false 10 minutes or more 6.771,3.146 7.094,3.417 0.323,0.271 10 false [H] 5.01,3.156 5.333,3.427 0.323,0.271 10 false [F] 5.906,2.729 6.635,3.188 0.729,0.458 10 false 10 minutes or more 1.365,3.458 6.813,3.719 5.448,0.26 10 false *: Drive the vehicle while keeping the engine load as constant as possible 0.344,0.229 3.708,0.427 3.365,0.198 10 false Vehicle Speed 6.74,3.417 7.125,3.646 0.385,0.229 10 false Time

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

8.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


9.

Turn the ignition switch off and wait for at least 30 seconds [C].

10.

Turn the ignition switch to ON and turn the GTS on.

11.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [D].

12.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


13.

Enter the following menus: Powertrain / Engine / Trouble Codes [F].

14.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



15.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

16.

Input the DTC: P042000 or P043000.

17.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE and no pending DTC is output, perform the following procedure.



18.

Drive the vehicle at a speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes or more [G].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


19.

Enter the following menus: Powertrain / Engine / Trouble Codes [H].

20.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



21.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

22.

Input the DTC: P042000 or P043000.

23.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

If a malfunction cannot be found when troubleshooting DTC P042000 or P043000, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P017100 and P017400 (System Too Lean) and P017200 and P017500 (System Too Rich).

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

DTC Suspected Area
P042000 Bank 1
P043000 Bank 2



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P042000 AND/OR P043000)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P042000 and/or P043000 is output A
P042000 and/or P043000 and other DTCs are output B


HINT:

If any DTCs other than P042000 and/or P043000 are output, troubleshoot those DTCs first.




A

2.READ FREEZE FRAME DATA (LONG FT B1S2 AND LONG FT B2S2)

B

GO TO DTC CHART

2.READ FREEZE FRAME DATA (LONG FT B1S2 AND LONG FT B2S2)
a.

Using the GTS, read the value displayed in the Freeze Frame Data.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA

Result:
GTS Display Result Proceed to
Long FT B1S2
Long FT B2S2
Less than 1.0% A
1.0% or higher B




A

3.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

14.CHECK FOR EXHAUST GAS LEAK
3.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.


b.

Warm up the air fuel ratio sensors at an engine speed of 2500 rpm for 90 seconds.


c.

Change the fuel injection volume using the GTS, and monitor the output current of the air fuel ratio sensor (sensor 1) (A/F (O2) Sensor Current B1S1 or A/F (O2) Sensor Current B2S1) and air fuel ratio sensor (sensor 2) (A/F (O2) Sensor Current B1S2 or A/F (O2) Sensor Current B2S2) displayed on the GTS.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
A/F (O2) Sensor Current B1S1
A/F (O2) Sensor Current B2S1
A/F (O2) Sensor Current B1S2
A/F (O2) Sensor Current B2S2
50004 372 8 230,432,564,609
HINT:
·

The Active Test "Control the Injection Volume for A/F Sensor" can be used to lower the fuel injection volume by 12.5% or increase the injection volume by 12.5%.

·

The air fuel ratio sensor (sensor 1) is displayed as A/F (O2) Sensor Current B1S1 or A/F (O2) Sensor Current B2S1, and the air fuel ratio sensor (sensor 2) is displayed as A/F (O2) Sensor Current B1S2 or A/F (O2) Sensor Current B2S2 on the GTS.

·

The air fuel ratio sensor (sensor 1) has an output delay of a few seconds and the air fuel ratio sensor (sensor 2) has a maximum output delay of approximately 20 seconds.

·

If the sensor output current does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard:
GTS Display
(Sensor)
Injection Volume Status Current
A/F (O2) Sensor Current B1S1
A/F (O2) Sensor Current B2S1
(Air fuel ratio (sensor 1))
12.5% Rich Below -0.075 mA
-12.5% Lean More than 0.037 mA
A/F (O2) Sensor Current B1S2
A/F (O2) Sensor Current B2S2
(Air fuel ratio (sensor 2))
12.5% Rich Below -0.86 mA
-12.5% Lean More than 0.33 mA


Result:
Status of A/F (O2) Sensor Current B1S1 or A/F (O2) Sensor Current B2S1 Status of A/F (O2) Sensor Current B1S2 or A/F (O2) Sensor Current B2S2 Actual air fuel ratio, air fuel ratio sensor (sensor 1) and air fuel ratio sensor (sensor 2) condition Main Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal
·

Three-way catalytic converter

·

Gas leak from exhaust system


A
Lean Lean/Rich Air fuel ratio sensor (sensor 1) malfunction
·

Air fuel ratio sensor (sensor 1)


B
Rich Lean/Rich Air fuel ratio sensor (sensor 1) malfunction
·

Air fuel ratio sensor (sensor 1)


Lean/Rich Lean Air fuel ratio sensor (sensor 2) malfunction
·

Air fuel ratio sensor (sensor 2)

·

Gas leak from exhaust system


C
Lean/Rich Rich Air fuel ratio sensor (sensor 2) malfunction
·

Air fuel ratio sensor (sensor 2)

·

Gas leak from exhaust system


Lean Lean Actual air fuel ratio lean
·

Extremely lean actual air fuel ratio

·

Gas leak from exhaust system


D
Rich Rich Actual air fuel ratio rich
·

Extremely rich actual air fuel ratio

·

Gas leak from exhaust system




Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor (sensor 1) output current (A/F (O2) Sensor Current B1S1 or A/F (O2) Sensor Current B2S1) is consistently more than 0.037 mA, and the air fuel ratio sensor (sensor 2) output current (A/F (O2) Sensor Current B1S2 or A/F (O2) Sensor Current B2S2) is consistently more than 0.33 mA.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor (sensor 1) output current (A/F (O2) Sensor Current B1S1 or A/F (O2) Sensor Current B2S1) is consistently below -0.075 mA, and the air fuel ratio sensor (sensor 2) output current (A/F (O2) Sensor Current B1S2 or A/F (O2) Sensor Current B2S2) is consistently below -0.86 mA.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output current of the air fuel ratio sensor (sensor 1) or air fuel ratio sensor (sensor 2) alternate correctly.


HINT:

Refer to "Data List / Active Test" [A/F (O2) Sensor Current B1S1, A/F (O2) Sensor Current B2S1, A/F (O2) Sensor Current B1S2, A/F (O2) Sensor Current B2S2].

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST




A

4.CHECK FOR EXHAUST GAS LEAK

B

5.REPLACE AIR FUEL RATIO SENSOR (SENSOR 1)

C

6.CHECK FOR EXHAUST GAS LEAK

D

8.CHECK FOR EXHAUST GAS LEAK
4.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks in exhaust system.



Result:
Proceed to
OK
NG



OK

13.CHECK DTC OUTPUT (DTC P042000 AND/OR P04300)

NG

10.REPAIR OR REPLACE EXHAUST SYSTEM
5.REPLACE AIR FUEL RATIO SENSOR (SENSOR 1)

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

11.CLEAR DTC
6.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks in exhaust system.



Result:
Proceed to
OK
NG



OK

7.REPLACE AIR FUEL RATIO SENSOR (SENSOR 2)

NG

10.REPAIR OR REPLACE EXHAUST SYSTEM
7.REPLACE AIR FUEL RATIO SENSOR (SENSOR 2)

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 2).

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

11.CLEAR DTC
8.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks in exhaust system.



Result:
Proceed to
OK
NG



OK

9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO

NG

10.REPAIR OR REPLACE EXHAUST SYSTEM
9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO
a.

Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P017100, P017200, P017400 and P017500 Inspection Procedure.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P017100


Result:
Proceed to
NEXT



NEXT

11.CLEAR DTC
10.REPAIR OR REPLACE EXHAUST SYSTEM
a.

Repair or replace exhaust system.

HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

11.CLEAR DTC
11.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P042000 and/or P043000 is output B




A

END

B

13.CHECK DTC OUTPUT (DTC P042000 AND/OR P04300)
13.CHECK DTC OUTPUT (DTC P042000 AND/OR P04300)
HINT:

Confirm the replacement parts, referring to the illustration in Catalyst Location.


a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P042000 is output A
P043000 is output B
P042000 and P043000 are output C




A

REPLACE CONVERTER ASSEMBLY RH (TWC: FRONT AND REAR CATALYST)

B

REPLACE CONVERTER ASSEMBLY LH (TWC: FRONT AND REAR CATALYST)

C

REPLACE CONVERTER ASSEMBLY RH AND LH (TWC: FRONT AND REAR CATALYST)

14.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks in exhaust system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

15.REPLACE AIR FUEL RATIO SENSOR (SENSOR 2)

NG

REPAIR OR REPLACE EXHAUST SYSTEM

15.REPLACE AIR FUEL RATIO SENSOR (SENSOR 2)

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 2).

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

16.CLEAR DTC
16.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:

DTCs are not output.



Result:
Proceed to
NEXT



NEXT

END