Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P052012  Engine Oil Pressure Sensor/Switch "A" Circuit Short to Battery  P052014  Engine Oil Pressure Sensor/Switch "A" Circuit Short to Ground or Open  


DESCRIPTION

A107720E86
0.135,0.708 1.406,1 1.271,0.292 10 false Voltage (V) 0.344,1.031 0.573,1.24 0.229,0.208 10 false 4.5 0.333,2.156 0.563,2.365 0.229,0.208 10 false 0.5 0.74,2.417 0.854,2.625 0.115,0.208 10 false 0 2.542,2.417 2.948,2.688 0.406,0.271 10 false 1.0 1.198,2.688 2.615,2.927 1.417,0.24 10 false Oil Pressure (MPa) 0.146,0.177 3.083,0.646 2.938,0.469 10 false Characteristics of Oil Pressure Sensor:

The oil pressure sensor utilizes a semiconductor type pressure sensor that changes resistance in accordance with changes in pressure. An internal electrical signal that varies with the change in resistance is amplified and sent to the ECM as the engine oil pressure signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P052012 Engine Oil Pressure Sensor/Switch "A" Circuit Short to Battery The oil pressure sensor output voltage is higher than 4.78 V for 5 seconds or more (1 trip detection logic).
·

Open or short in oil pressure sensor circuit

·

Oil pressure sensor

·

ECM


Comes on SAE: P0523
P052014 Engine Oil Pressure Sensor/Switch "A" Circuit Short to Ground or Open The oil pressure sensor output voltage is below 0.23 V for 5 seconds or more (1 trip detection logic).
·

Open or short in engine oil pressure sensor circuit

·

Oil pressure sensor

·

ECM


Comes on SAE: P0522

Related Data List
DTC No. Data List
P052012 Engine Oil Pressure
P052014

MONITOR DESCRIPTION

The ECM calculates the engine oil pressure based on the output voltage of the oil pressure sensor. If the signal output from the engine oil pressure sensor is outside of the specified range, the MIL is illuminated and a DTC is stored.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Wait 10 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P052012 or P052014.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions




HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.



WIRING DIAGRAM

A478140E02
1.094,1.719 1.625,1.927 0.531,0.208 10 false PEO 1.198,1.031 1.729,1.24 0.531,0.208 10 false VC 1.198,2.5 1.729,2.708 0.531,0.208 10 false E2 4.75,0.938 5.281,1.146 0.531,0.208 10 false VCPE 4.479,0.938 5.01,1.146 0.531,0.208 10 false 80 4.49,2.385 5.021,2.594 0.531,0.208 10 false 79 4.49,1.625 5.021,1.833 0.531,0.208 10 false 73 4.896,2.115 5.427,2.323 0.531,0.208 10 false 200 kΩ 4.75,2.365 5.281,2.573 0.531,0.208 10 false EPEO 4.75,1.625 5.281,1.833 0.531,0.208 10 false PEO 5.5,3.292 6.031,3.5 0.531,0.208 10 false ECM 5.49,3.125 6.021,3.333 0.531,0.208 10 false C37 0.354,2.917 0.885,3.125 0.531,0.208 10 false C27 0.354,3.083 4.26,3.479 3.906,0.396 10 false Oil Pressure Sensor 1.5,0.927 2.031,1.135 0.531,0.208 10 false 3 1.51,1.615 2.042,1.823 0.531,0.208 10 false 2 1.51,2.396 2.042,2.604 0.531,0.208 10 false 1 6.115,0.688 6.646,0.896 0.531,0.208 10 false 5 V

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the oil pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(C27)Location & Routing

Click Connector(C27)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Oil Sensor Pressure

C27-3 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V
C27-2 (PEO) - Body ground Ignition switch ON Below 0.1 V



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C27)Location & Routing

Click Connector(C27)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Oil Sensor Pressure

C27-2 (PEO) - C27-1 (E2) Ignition switch off 190 to 210 kΩ
C27-1 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE OIL PRESSURE SENSOR (OIL PRESSURE SENDER GAUGE ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE OIL PRESSURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (ENGINE OIL PRESSURE SENSOR - ECM)
a.

Disconnect the oil pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C27,C37)Location & Routing

Click Connector(C27)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Oil Sensor Pressure

Click Connector(C37)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

C27-1 (E2) - C37-79 (EPEO) Always Below 1 Ω
C27-2 (PEO) - C37-73 (PEO) Always Below 1 Ω
C27-3 (VC) - C37-80 (VCPE) Always Below 1 Ω
C27-1 (E2) or C37-79 (EPEO) - Body ground and other terminals Always 10 kΩ or higher
C27-2 (PEO) or C37-73 (PEO) - Body ground and other terminals Always 10 kΩ or higher
C27-3 (VC) or C37-80 (VCPE) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR