Home › Engine / Hybrid System › 1GR-FE (EMISSION CONTROL) › PURGE VALVE
RM38G0E _51 Engine / Hybrid System _101531 1GR-FE EMISSION CONTROL _0470512 PURGE VALVE A

1GR-FE EMISSION CONTROL  PURGE VALVE  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A489053N01
5.938,2.302 7.104,2.469 1.167,0.167 5.438,1.365 5.635,0.969 5.635,0.969 5.802,0.969 true 4.5,1.167 4.667,1.167 4.667,1.167 4.917,1.417 true 6.25,1.833 6.5,1.25 6.5,1.25 6.667,1.25 true 5.854,1.969 5.854,2.385 5.854,2.385 5.938,2.385 false 6.146,0.833 6.646,1.125 0.5,0.292 18 false 1 4.333,1.083 4.5,1.25 0.167,0.167 10 false *1 6.75,1.167 6.917,1.333 0.167,0.167 10 false *2 6.063,2.323 7.063,2.49 1,0.167 8 false 9.0 (92, 80 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PURGE VSV (NO. 1 VACUUM SWITCHING VALVE ASSEMBLY) 25860 (Click here) - -

*1 NO. 1 FUEL VAPOR FEED HOSE *2 FUEL VAPOR FEED HOSE
V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

PROCEDURE

Hide 25860 1.INSTALL PURGE VSV (NO. 1 VACUUM SWITCHING VALVE ASSEMBLY)

a.
A489034C01
1.396,4.042 1.583,3.583 1.583,3.583 1.667,3.583 true 2.542,4.135 2.917,4.292 2.917,4.292 3,4.292 true 1.729,3.51 1.896,3.677 0.167,0.167 10 false *a 3.052,4.208 3.219,4.375 0.167,0.167 10 false *a 1.531,4.438 1.698,4.604 0.167,0.167 10 false *b 2.969,3.708 3.135,3.875 0.167,0.167 10 false *c 2.5,3.49 2.667,3.656 0.167,0.167 10 false *d 0.135,0.104 0.417,0.458 0.281,0.354 18 false i 3.323,0.115 3.604,0.469 0.281,0.354 18 false ii 0.479,2.156 0.76,2.448 0.281,0.292 18 true iii 3.719,2.646 4,2.938 0.281,0.292 18 true iv
*a Paint Mark *b 2 to 5 mm (0.0788 to 0.1968 in.)
*c 120° *d Upper Side


i.

Install the purge VSV (No. 1 vacuum switching valve assembly) with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


ii.

Connect the connector.


iii.

Connect the fuel vapor feed hose to the purge VSV (No. 1 vacuum switching valve assembly) and slide the hose clip to secure it.

NOTICE:
·

Align the hose and the hose clip at the locations shown in the illustration and install them.

·

Make sure the fuel vapor feed hose is securely inserted to the stopper.




iv.

Connect the No. 1 fuel vapor feed hose to the purge VSV (No. 1 vacuum switching valve assembly).