Home › Engine / Hybrid System › 1GR-FE (STARTING) › STARTER
RM38G0E _51 Engine / Hybrid System _101534 1GR-FE STARTING _0470526 STARTER A

1GR-FE STARTING  STARTER  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
A488751N01
0.042,2.646 1,2.823 0.958,0.177 0.885,0.156 1.865,0.333 0.979,0.177 0.083,4.719 1.052,4.906 0.969,0.188 5.802,3.438 6.813,3.625 1.01,0.188 5.792,0.74 5.792,0.375 5.792,0.375 6,0.375 false 5.01,1.969 4.823,1.969 4.823,1.969 4.656,1.604 false 3.719,1.156 3.719,0.438 3.719,0.438 3.99,0.438 false 3.26,2.51 3.01,2.51 3.01,2.51 2.833,2.083 false 2.458,2.802 2.073,2.802 2.073,2.802 2.073,2.25 false 2.115,1.323 2.344,0.802 2.344,0.802 2.552,0.802 false 1.396,2.99 1.177,2.99 1.177,2.99 1.177,2.521 false 3.833,3.427 4.021,3.094 4.021,3.094 4.208,3.094 false 3.385,3.552 3.385,3.208 3.385,3.208 3.552,3.208 false 2.771,3.729 3.073,3.729 false 5.281,4.667 5.635,5.167 5.635,5.167 5.906,5.167 false 4.073,5.177 3.823,5.177 3.823,5.177 3.823,4.781 false 3.198,5.344 2.938,5.344 2.938,5.344 2.938,4.802 false 2.906,4.25 3.104,4.25 3.104,4.25 3.292,4.656 false 2.26,5.552 1.948,5.552 1.948,5.552 1.948,5.313 false 0.646,0.75 0.646,0.24 0.646,0.24 0.875,0.24 false 5.625,3.823 5.625,3.521 5.625,3.521 5.802,3.521 false 0.615,4.719 0.615,4.5 0.615,4.5 0.948,4.5 false 0.51,2.646 0.51,2.188 false 6.063,0.229 6.344,0.5 0.281,0.271 18 false 1 4.302,0.292 4.583,0.563 0.281,0.271 18 false 4 2.563,5.427 2.844,5.698 0.281,0.271 18 false 3 3.25,5.271 3.521,5.448 0.271,0.177 10 false *5 4.208,5.115 4.479,5.292 0.271,0.177 10 false *4 2.74,4.167 3.01,4.344 0.271,0.177 10 false *9 4.281,3.021 4.552,3.198 0.271,0.177 10 false *6 3.604,3.135 3.875,3.313 0.271,0.177 10 false *7 2.604,3.646 2.875,3.823 0.271,0.177 10 false *8 1.448,2.927 1.719,3.104 0.271,0.177 10 false *1 3.313,2.417 3.583,2.594 0.271,0.177 10 false ● 5.063,1.875 5.333,2.052 0.271,0.177 10 false ● 0.573,2.229 0.844,2.406 0.271,0.177 10 false x 2 2.26,1.271 2.531,1.448 0.271,0.177 10 false x 4 0.708,0.823 0.979,1 0.271,0.177 10 false x 2 2.771,2.667 3.052,2.938 0.281,0.271 18 false 2 5.958,5.094 6.229,5.271 0.271,0.177 10 false *3 5.49,3.938 5.76,4.115 0.271,0.177 10 false x 2 2.635,0.729 2.906,0.906 0.271,0.177 10 false *2 0.927,0.177 1.927,0.333 1,0.156 8 false 5.9 (60, 52 in.*lbf) 0.125,4.74 1.125,4.896 1,0.156 8 false 5.9 (60, 52 in.*lbf) 5.854,3.458 6.854,3.615 1,0.156 8 false 5.9 (60, 52 in.*lbf) 0.083,2.667 1.083,2.823 1,0.156 8 false 1.5 (15, 13 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 STARTER ARMATURE ASSEMBLY 28160 - - -
2 STARTER BRUSH HOLDER ASSEMBLY 28140 (Click here) - -
3 MAGNET STARTER SWITCH ASSEMBLY 28150 (Click here) - -
4 STARTER YOKE ASSEMBLY 28120 (Click here) - -

*1 STARTER COMMUTATOR END FRAME *2 SPRING
*3 STARTER DRIVE HOUSING *4 STARTER CLUTCH
*5 RETURN SPRING *6 IDLE GEAR
*7 RETAINER *8 CLUTCH ROLLER
*9 STEEL BALL - -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

High-temperature Grease - -

PROCEDURE

Hide 28160 1.INSTALL STARTER ARMATURE ASSEMBLY

Hide 28140 2.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
A489736C01
2.188,0.177 2.438,0.438 0.25,0.26 18 false i 2.177,0.49 2.427,0.75 0.25,0.26 18 false ii 0.417,2.01 0.667,2.313 0.25,0.302 18 false iii 4.51,2.083 4.76,2.354 0.25,0.271 18 false iv

i.

Install the starter brush holder assembly.


ii.

Connect the 4 brushes to the starter brush holder assembly.

1. Using a screwdriver, hold back the brush spring.

2. Connect the brush to the starter brush holder assembly.

NOTICE:

Check that positive (+) lead wires are not grounded.



iii.

Install a new O-ring in position on the starter yoke assembly.


iv.

Install the starter commutator end frame assembly to the starter yoke assembly with the 2 screws.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)



Hide 28150 3.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.
A489731C01
3.198,2.115 3.26,2.448 3.26,2.448 3.438,2.448 false 2.323,2.427 2.125,2.427 2.125,2.427 1.875,1.979 false 1.885,0.844 2.125,0.458 2.125,0.458 2.302,0.458 false 1.552,1.115 1.75,1.302 1.75,1.302 1.906,1.302 false 0.708,1.406 0.979,1.406 0.979,1.406 1.156,1.219 false 0.635,2.438 0.844,2.438 0.844,2.438 0.917,2.01 false 1.573,2.427 1.396,2.427 1.396,2.427 1.396,1.885 false 3.479,2.385 3.792,2.542 0.313,0.156 10 false *1 2.354,2.344 2.667,2.5 0.313,0.156 10 false *2 2.354,0.385 2.667,0.542 0.313,0.156 10 false *3 1.948,1.219 2.26,1.375 0.313,0.156 10 false *4 0.542,1.323 0.854,1.479 0.313,0.156 10 false *5 0.479,2.354 0.792,2.51 0.313,0.156 10 false *6 1.625,2.333 1.938,2.521 0.313,0.188 10 false *7 0.427,0.198 0.646,0.469 0.219,0.271 18 false i 4.094,0.208 4.313,0.479 0.219,0.271 18 false ii 0.385,0.563 0.854,0.875 0.469,0.313 18 false iii-v
*1 Starter Drive Housing Assembly *2 Starter Clutch Sub-assembly
*3 Idle Gear *4 Retainer
*5 Clutch Roller *6 Return Spring
*7 Steel Ball - -
V100135

High-Temperature Grease - -


i.

Apply high-temperature grease to the idle gear, steel ball, return spring, clutch roller and retainer.


ii.

Insert the steel ball into the starter clutch hole.


iii.

Insert the return spring to the starter clutch hole.


iv.

Install the starter clutch sub-assembly, idle gear, retainer and clutch roller to the starter drive housing assembly.


v.

Install the magnet starter switch assembly to the starter drive housing assembly with the 2 screws.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)



Hide 28120 4.INSTALL STARTER YOKE ASSEMBLY

a.
A488759C01
0.583,0.25 0.813,0.521 0.229,0.271 18 false i 3.719,0.25 3.958,0.5 0.24,0.25 18 false ii 1.958,2.125 2.49,2.417 0.531,0.292 18 false iii, iv

i.

Install a new O-ring to the groove of the starter yoke assembly.


ii.

Align the claw of the starter yoke assembly with the groove of the magnet starter switch assembly.


iii.

Install the starter yoke assembly and starter commutator end frame together with the starter armature assembly to the magnet starter switch assembly with the 2 bolts.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


iv.

Connect the lead wire to terminal C with the nut.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)