Home › Engine / Hybrid System › 1GR-FE (STARTING) › STARTER
RM38G0E _51 Engine / Hybrid System _101534 1GR-FE STARTING _0470526 STARTER A

1GR-FE STARTING  STARTER  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A488742N01
1.021,0.469 1.188,0.469 1.188,0.469 1.354,0.802 true 2.823,2.948 2.99,2.563 2.99,2.563 3.24,2.563 true 1.073,2.646 1.344,1.969 1.344,1.969 1.594,1.969 true 4.5,3.615 4.667,3.615 4.667,3.615 4.833,3.948 true 1.885,3.521 2.042,3.885 2.042,3.885 2.208,3.885 true 6.208,0.354 6.625,0.354 true 6.208,0.781 6.625,0.781 true 0.813,0.344 1.063,0.677 0.25,0.333 18 false 3 3.344,2.427 3.594,2.76 0.25,0.333 18 false 4 1.698,1.813 1.948,2.146 0.25,0.333 18 false 5 4.271,3.5 4.521,3.833 0.25,0.333 18 false 6 2.313,3.802 2.625,4 0.313,0.198 10 false *1 2.656,2.333 2.969,2.531 0.313,0.198 10 false x 2 5.906,0.198 6.156,0.531 0.25,0.333 18 true 1 5.896,0.635 6.146,0.969 0.25,0.333 18 true 2 3.521,3.229 3.833,3.427 0.313,0.198 10 false x 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
3 EXHAUST MANIFOLD ASSEMBLY LH 17150 - - -
4 STARTER COVER 28192 - - -
5 STARTER ASSEMBLY 28100 - - -
6 FLYWHEEL HOUSING SIDE COVER 11363A - - -

*1 ENGINE WIRE - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the starter assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)
·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 2)

·

Gas leaks from exhaust system


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 17150 3.REMOVE EXHAUST MANIFOLD ASSEMBLY LH

Hide 28192 4.REMOVE STARTER COVER

a.
A488738


Hide 28100 5.REMOVE STARTER ASSEMBLY

a.
A488739


Hide 11363A 6.REMOVE FLYWHEEL HOUSING SIDE COVER

a.
A488741