Home › Power Source / Network › 1GR-FE (BATTERY / CHARGING) › GENERATOR
RM38G0E _57 Power Source / Network _101114 1GR-FE BATTERY / CHARGING _0470530 GENERATOR A

1GR-FE BATTERY / CHARGING  GENERATOR  REASSEMBLY  


CAUTION / NOTICE / HINT

A484900N01
6.115,2.76 7.094,2.906 0.979,0.146 4.115,1.771 5.063,1.917 0.948,0.146 3.448,3.125 4.469,3.292 1.021,0.167 6.052,3.448 7.073,3.635 1.021,0.188 4.833,4.667 5.813,4.833 0.979,0.167 1.417,2.792 2.25,3.125 0.833,0.333 5.875,3.094 5.875,2.844 5.875,2.844 6.125,2.844 false 0.729,2.771 0.833,3.167 0.833,3.167 0.917,3.167 false 1.25,2.667 1.333,2.917 1.333,2.917 1.417,2.917 false 2.25,1.177 2.167,1.177 2.167,1.177 2,1.427 false 3,1.917 3.083,2.167 3.083,2.167 3.25,2.167 false 3.667,0.667 3.5,0.667 3.5,0.667 3.417,1.354 false 3.792,1.427 4.042,1.844 4.042,1.844 4.125,1.844 false 4.531,0.813 4.615,0.396 4.615,0.396 4.781,0.396 false 5.333,0.583 5.25,0.583 5.25,0.583 5.167,0.833 false 2.979,5.042 3.031,5.365 3.031,5.365 3.115,5.365 false 3.365,3.615 3.365,3.198 3.365,3.198 3.448,3.198 false 4.083,4.115 4.417,5.25 4.417,5.25 4.583,5.25 false 4.26,3.802 4.667,4.75 4.667,4.75 4.833,4.75 false 4.792,3.177 4.875,2.76 4.875,2.76 4.958,2.76 false 5.365,2.938 5.51,2.635 5.51,2.635 5.594,2.635 false 1.365,4.021 1.531,3.854 1.531,3.854 1.698,3.854 false 5.719,3.542 6.052,3.542 false 6.156,2.76 7.115,2.906 0.958,0.146 8 false 6.2 (63, 55 in.*lbf) 5.667,3.625 5.917,3.771 0.25,0.146 10 false x 3 6.125,3.469 7.125,3.604 1,0.135 8 false 4.6 (47, 41 in.*lbf) 1.094,3.031 1.375,3.385 0.281,0.354 18 false 8 0.969,3.073 1.125,3.271 0.156,0.198 10 false ● 2.74,2.833 3.021,3.188 0.281,0.354 18 false 7 2.302,1.115 2.615,1.313 0.313,0.198 10 false *1 3.75,2.01 4.031,2.365 0.281,0.354 18 false 1 3.635,2.063 3.792,2.26 0.156,0.198 10 false ● 3.75,0.594 4.031,0.948 0.281,0.354 10 false *4 3.885,1.375 4.156,1.552 0.271,0.177 10 false x 4 4.146,1.771 5.104,1.948 0.958,0.177 8 false 2.3 (23, 20 in.*lbf) 4.875,0.271 5.156,0.625 0.281,0.354 18 false 2 5.406,0.5 5.719,0.698 0.313,0.198 10 false *2 1.771,3.74 2.052,4.094 0.281,0.354 18 false 5 3.531,5.313 3.813,5.667 0.281,0.354 18 false 3 3.479,3.573 3.865,3.781 0.385,0.208 10 false x 4 3.5,3.135 4.573,3.281 1.073,0.146 8 false 5.9 (60, 52 in.*lbf) 4.354,3.677 4.583,3.865 0.229,0.188 10 false x 2 5.073,5.156 5.354,5.51 0.281,0.354 18 false 4 4.854,4.677 5.813,4.854 0.958,0.177 8 false 1.8 (18, 16 in.*lbf) 5.021,2.615 5.302,2.969 0.281,0.354 18 false 6 5.625,2.542 5.938,2.74 0.313,0.198 10 false *3 1.51,2.813 2.25,3 0.74,0.188 8 false 80 (816, 59) 1.5,2.958 2.219,3.135 0.719,0.177 8 false 64 (653, 47)*

Procedure Part Name Code
Z101186

Z101188

Z101187

1 GENERATOR DRIVE END FRAME BEARING 27310B (Click here) - -
2 GENERATOR ROTOR ASSEMBLY 27330 - - -
3 GENERATOR COIL ASSEMBLY 27360 (Click here) - -
4 GENERATOR BRUSH HOLDER ASSEMBLY 27370 (Click here) - -
5 GENERATOR TERMINAL INSULATOR 27387B - - -
6 GENERATOR REAR END COVER 27039 - - -
7 GENERATOR PULLEY WITH CLUTCH 27415 (Click here) - -
8 GENERATOR PULLEY CAP 27416 - - -

*1 GENERATOR DRIVE END FRAME *2 GENERATOR WASHER
*3 CORD CLIP *4 RETAINER PLATE
V100146

N*m (kgf*cm, ft.*lbf): Specified torque * For use with SST
● Non-reusable part - -

PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A461907C04
1.281,0.948 0.781,0.458 0.781,0.458 1.323,0.375 true 2.615,0.51 2.948,0.333 2.948,0.333 2.708,0.677 true 5.656,0.49 6.198,0.74 true 6.229,1.115 6.813,1.5 true 2.927,0.146 3.385,0.344 0.458,0.198 10 false SST 0.5,0.396 0.958,0.594 0.458,0.198 10 false SST 5.417,0.365 5.875,0.563 0.458,0.198 10 false *a 6.875,1.438 7.135,1.708 0.26,0.271 10 false *b 0.427,0.073 0.906,0.406 0.479,0.333 18 false i 4.073,0.063 4.688,0.396 0.615,0.333 18 false ii,iii
*a Tab *b Cutout


i.

Using SST and a press, install a new generator drive end frame bearing.

SST
09950-60011  (09951-00470)
09950-70010  (09951-07100)


ii.

Fit the tabs of the retainer plate into the cutouts of the generator drive end frame to install the retainer plate.


iii.

Install the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)



Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

Hide 27360 3.INSTALL GENERATOR COIL ASSEMBLY

a.
A484863N01
1.146,0.094 1.427,0.448 0.281,0.354 18 false i 4.26,0.052 4.813,0.406 0.552,0.354 18 false ii

i.

Using a 21 mm deep socket wrench and press, slowly press in the generator coil assembly.


ii.

Install the 4 bolts.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)



Hide 27370 4.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A461910C03
0.813,0.479 1.219,0.302 1.219,0.302 1.948,0.615 true 6.365,1.094 6.365,0.865 false 1.208,0.854 1.49,1.208 0.281,0.354 18 false i 0.417,0.104 0.698,0.458 0.281,0.354 18 false i 2.698,0.031 2.979,0.385 0.281,0.354 18 false ii 5.302,0.031 5.583,0.385 0.281,0.354 18 false iii 1.167,0.135 1.479,0.333 0.313,0.198 10 false *a 6.292,1.146 6.604,1.344 0.313,0.198 10 false *a
*a Pin (1.0 mm) - -
V100136

Pull out - -


i.

While pushing the 2 brushes into the generator brush holder assembly, insert a 1.0 mm (0.0394 in.) pin into the generator brush holder assembly hole.


ii.

Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


iii.

Pull out the pin from the generator brush holder assembly hole.



Hide 27387B 5.INSTALL GENERATOR TERMINAL INSULATOR

Hide 27039 6.INSTALL GENERATOR REAR END COVER

a.
A484901C01
4.25,0.333 4.333,0.333 4.333,0.333 4.583,0.5 true 2.344,1.365 2.5,1.563 0.156,0.198 10 false A 2.594,0.375 2.75,0.573 0.156,0.198 10 false A 1.49,0.635 1.646,0.833 0.156,0.198 10 false A 4.646,1.156 4.802,1.354 0.156,0.198 10 true B 3.99,0.25 4.302,0.448 0.313,0.198 10 false *1
*1 Cord Clip - -


Torque:
Nut A : 4.6 N*m (47 kgf*cm, 41 in.*lbf)
Nut B : 6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 27415 7.INSTALL GENERATOR PULLEY WITH CLUTCH

a.
A461912C02
5.125,0.625 5.396,0.625 false 5.969,1.177 6.281,0.917 false 1.406,2.438 1.615,2.208 true 0.635,3.115 0.635,2.719 true 1.698,3 1.76,2.823 false 5.042,2.302 5.25,2.073 true 4.51,3.313 4.51,2.917 true 5.552,2.99 5.719,2.823 false 4.625,0.563 5.542,0.76 0.917,0.198 10 false SST(A) 6.229,0.719 7.146,0.917 0.917,0.198 10 false SST(B) 0.417,3.188 1.333,3.385 0.917,0.198 10 false SST(A) 1.427,3.063 2.344,3.26 0.917,0.198 10 false SST(A) 1.698,2.083 2.615,2.281 0.917,0.198 10 false *a 5.313,2 6.229,2.198 0.917,0.198 10 false *1 5.188,3.031 6.104,3.229 0.917,0.198 10 false SST(B) 4.302,3.365 5.219,3.563 0.917,0.198 10 false SST(B) 0.427,0.094 0.958,0.563 0.531,0.469 18 false i 2.438,0.083 2.969,0.552 0.531,0.469 18 false ii 5.01,0.063 5.542,0.531 0.531,0.469 18 false iii 0.417,1.885 0.948,2.354 0.531,0.469 18 false iv 4.073,2 4.604,2.469 0.531,0.469 18 false v
*1 Generator Pulley with Clutch - -
*a Rotor Shaft - -


i.

Secure the generator drive end frame in a vise between aluminum plates.


ii.

Temporarily install a new generator pulley with clutch to the rotor shaft.


iii.

Install SST (A) to SST (B) as shown in the illustration.

SST
09820-63021  


iv.

Fit the rotor shaft end into SST (A).


v.

Fit SST (B) to the generator pulley with clutch.



b.
A461913C02
0.885,0.469 1.219,0.708 false 0.76,0.875 1.021,0.875 false 0.26,0.813 1.177,1.01 0.917,0.198 10 false SST(A) 0.396,0.385 1.313,0.583 0.917,0.198 10 false SST(B) 2.313,1 3.229,1.198 0.917,0.198 10 false *b 1.604,1.615 1.844,1.792 0.24,0.177 10 true *a 1.167,2.042 1.406,2.219 0.24,0.177 10 true *c 0.406,0.063 1.104,0.427 0.698,0.365 18 false i 3.802,0.521 4.5,0.885 0.698,0.365 18 false ii,iii 5.688,0.531 6.385,0.896 0.698,0.365 18 false iv
*a Torque Wrench Fulcrum Length *b Turn
*c Hold - -


i.

Tighten the generator pulley with clutch by turning SST (B) as shown in the illustration.

Torque:
Specified tightening torque : 80 N*m (816 kgf*cm, 59 ft.*lbf)

NOTICE:
·

Check that the generator drive end frame is secured in the vise tightly.

·

Hold SST (A) tightly during the operation.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 100 mm (3.94 in.)) + torque wrench (fulcrum length of 400 mm (1.31 ft.)): 64 N*m (653 kgf*cm, 47 ft.*lbf)




ii.

Remove SST (A) and (B) from the generator pulley with clutch.


iii.

Check that the generator pulley with clutch rotates smoothly.


iv.

Remove the generator drive end frame from the vise.



Hide 27416 8.INSTALL GENERATOR PULLEY CAP