Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100728 PARK ASSIST / MONITORING _0469676 PANORAMIC VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit is the power source circuit to operate the parking assist ECU. The parking assist ECU controls the panoramic view monitor system.

WIRING DIAGRAM

E301406E96
5.323,2.854 6.615,3.042 1.292,0.188 10 false Parking Assist ECU 5.313,2.708 5.625,2.896 0.313,0.188 10 false I60 5.302,2.125 5.75,2.323 0.448,0.198 10 false GND 5.302,1.708 5.646,1.896 0.344,0.188 10 false ACC 5.302,1.313 5.51,1.5 0.208,0.188 10 false IG 5.302,0.865 5.552,1.042 0.25,0.177 10 false +B 5.104,0.781 5.26,0.979 0.156,0.198 10 false 1 5.115,1.188 5.271,1.385 0.156,0.198 10 false 3 5.104,1.625 5.26,1.823 0.156,0.198 10 false 2 5.125,2.021 5.281,2.219 0.156,0.198 10 false 4 3.167,1.073 4.688,1.333 1.521,0.26 10 false ECU-DCC NO.1 3.188,1.479 4.344,1.74 1.156,0.26 10 false ECU-IGR NO.1 3.344,1.917 4.01,2.156 0.667,0.24 10 false ECU-ACC 1.438,0.885 2.802,1.115 1.365,0.229 10 false from Battery 0.844,1.302 2.323,1.51 1.479,0.208 10 false from IGR-NO.1 Relay 1.24,1.708 2.281,1.938 1.042,0.229 10 false from ACC Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuse for circuits related to this system before performing the following procedure.


HINT:

If the parking assist ECU does not operate due to a power source problem, other system DTCs may be stored due to a CAN communication interruption.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
a.

Disconnect the parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I60)Location & Routing

Click Connector(I60)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Parking Assist ECU

I60-4 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I60)Location & Routing

Click Connector(I60)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Parking Assist ECU

I60-1 (+B) - I60-4 (GND) Ignition switch off 11 to 14 V
I60-2 (ACC) - I60-4 (GND) Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
I60-3 (IG) - I60-4 (GND) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR