Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for V35A-FTS)
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0472752 AUTOMATIC TRANSMISSION SYSTEM(for V35A-FTS) C

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for V35A-FTS)  P071000  Transmission Fluid Temperature Sensor "A" Circuit Range/Performance  


DESCRIPTION

The No. 1 ATF temperature sensor converts the fluid temperature into a resistance value for use by the TCM.

The TCM applies a voltage to the temperature sensor through terminal THO1 of the TCM.

The sensor resistance changes with the ATF temperature. As the temperature becomes higher, the sensor resistance decreases.

One terminal of the sensor is grounded so that the sensor resistance and voltage go down as the temperature becomes higher.

The TCM calculates the fluid temperature based on the voltage signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P071000 Transmission Fluid Temperature Sensor "A" Circuit Range/Performance Either condition is met: (2-trip detection logic)
·

Certain monitor enabling conditions are met and the ATF temperature is below 20°C (68°F)

·

Certain monitor enabling conditions are met and the ATF temperature is 100°C (212°F) or higher


·

Transmission fluid level

·

Transmission wire (No. 1 ATF temperature sensor)


Comes on DTC stored SAE: P0711

DTC Detection Condition Patterns
Vehicle Condition
Pattern 1 Pattern 2
Diagnostic Condition Certain monitor enabling conditions are met. ○ ○
Malfunction Condition ATF temperature is below 20°C (68°F). ○ -
ATF temperature is 100°C (212°F) or higher. - ○
Duration - -
Detection Logic 2-trip detection logic 2-trip detection logic

HINT:

This DTC is stored when either of the above detection patterns is met.


MONITOR DESCRIPTION

This DTC indicates that there is a problem with output from the No. 1 ATF temperature sensor and that the sensor itself is defective. The ATF temperature sensor converts the ATF temperature into an electrical resistance value. Based on the resistance, the TCM determines the ATF temperature and detects an opens or shorts in the ATF temperature circuit or a malfunction of the ATF temperature sensor.

After driving the vehicle for a certain period of time, the ATF temperature should increase. If the ATF temperature is below 20°C (68°F) after driving the vehicle for a certain period, the TCM interprets this as a malfunction, illuminates the MIL and stores this DTC.

When the ATF temperature is 100°C (212°F) or higher and the engine coolant temperature takes 10 seconds or more to reach 60°C (140°F) after a cold start, the TCM also determines this as a malfunction, illuminates the MIL and stores this DTC.

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

Drive the vehicle 8 km (4.97 mile) or more over a period of 22 minutes or more.

4.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

5.

Input the DTC: P071000.

6.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for V35A-FTS)>PRECAUTION


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values.


a.

Warm up the engine.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Powertrain / Transmission / Data List / A/T Oil Temperature No.1.


d.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Temperature No.1 ATF temperature sensor value Min.: -40°C (-40°F)
Max.: 150°C (302°F)
·

Approximately 80°C (176°F): After stall speed test

·

Equal to ambient temperature: While engine is cold


If value is -40°C (-40°F) or 150°C (302°F), ATF temperature sensor circuit is open or shorted
Powertrain > Transmission > Data List
Tester Display
A/T Oil Temperature No.1
50003 373 180
HINT:
·

When DTC P071011 is output and the GTS shows 150°C (302°F) or higher, there is a short circuit.

·

When DTC P071015 is output and the GTS shows -40°C (-40°F), there is an open circuit.

Check the temperature displayed on the GTS in order to check if a malfunction exists.



Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
150°C (302°F) or higher Short circuit

HINT:

If a circuit related to the ATF temperature sensor becomes open, P071015 will be stored in approximately 0.5 seconds. It is not necessary to inspect the circuit when P071000 is output.




PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P071000)
a.

Read the DTCs using the GTS.

Powertrain > Transmission > Trouble Codes
50001 373
Result:
Result Proceed to
Only DTC P071000 is output A
DTC P071000 and other DTCs are output B


HINT:

If any DTCs other than DTC P071000 are output, perform troubleshooting for those DTCs first.




A

2.INSPECT TRANSMISSION FLUID LEVEL

B

GO TO DTC CHART

2.INSPECT TRANSMISSION FLUID LEVEL

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION FLUID>ADJUSTMENT

OK:

Automatic transmission fluid level is correct.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE TRANSMISSION WIRE (NO. 1 ATF TEMPERATURE SENSOR)

NG