The transmission revolution sensor (NT) detects the input shaft rotation speed and sends it to the TCM.
Based on the transmission revolution sensor (NT) signal and the transmission revolution sensor (SP2) signals, the TCM controls engine torque and shift timing. Based on the input shaft rotation speed and the engine speed signal, lock-up control is performed.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P071512 | Input/Turbine Speed Sensor "A" Circuit Short to Battery | When the ignition switch is ON, the transmission revolution sensor (NT) input voltage is higher than 1.9 V for 4.5 seconds or more (1-trip detection logic). |
·
Harness and connector
·
Transmission wire
·
Transmission revolution sensor (NT)
·
TCM |
Comes on | DTC stored | SAE: P07C0 |
| P071514 | Input/Turbine Speed Sensor "A" Circuit Short to Ground or Open | When the ignition switch is ON, the transmission revolution sensor (NT) input voltage is below 0.1 V for 4.5 seconds or more (1-trip detection logic). |
·
Harness and connector
·
Transmission wire
·
Transmission revolution sensor (NT)
·
TCM |
Comes on | DTC stored | SAE: P07BF |
| P071531 | Input/Turbine Speed Sensor "A" No Signal | All conditions are met for 5 seconds or more (1-trip detection logic):
·
Transmission revolution sensor (SP2) value is 27 km/h (16.78 mph) or more.
·
Vehicle speed is 27 km/h (16.78 mph) or more.
·
Shift lever is in D.
·
Transmission revolution sensor (NT) value is less than 300 rpm. |
·
Harness and connector
·
Transmission wire
·
Transmission revolution sensor (NT)
·
TCM |
Comes on | DTC stored | SAE: P0717 |
The NT terminal of the TCM detects a pulse signal from the transmission revolution sensor (NT) (input RPM). The TCM calculates gear shifts comparing the transmission revolution sensor (NT) with the transmission revolution sensor (SP2).
While the vehicle is being driven with the shift lever in D, if the input shaft revolution (speed) is less than 300 rpm*1 when the output shaft speed is 27 km/h (16.78 mph) or more, the TCM interprets this as a malfunction, illuminates the MIL and stores a DTC.
*: Pulse is not output or is irregularly output.
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Perform the D Position Shift Test inspection in Road Test.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P071512, P071514 or P071531.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL |
·
DTC judgment completed
·
System normal |
| ABNORMAL |
·
DTC judgment completed
·
System abnormal |
| INCOMPLETE |
·
DTC judgment not completed
·
Perform driving pattern after confirming DTC enabling conditions |
| N/A |
·
Unable to perform DTC judgment
·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Perform registration and/or initialization when parts related to the automatic transmission are replaced.
DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| NT Sensor Speed | Input shaft speed | Min.: 0 rpm Max.: 12750 rpm |
·
Equal to engine speed: Lock-up on (after warming up engine)
·
Nearly equal to engine speed: Lock-up off (idling with shift lever in N) |
Data is displayed in increments of 50 rpm |
| Tester Display |
|---|
| NT Sensor Speed |
NT Sensor Speed is always 0 while driving: Open or short in the sensor or circuit.
NT Sensor Speed is always more than 0 and less than 300 rpm while driving the vehicle at 27 km/h (16.78 mph) or more: Sensor malfunction, improper installation, or intermittent connection malfunction in the circuit.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| NT Sensor Speed | Input shaft speed | Min.: 0 rpm Max.: 12750 rpm |
·
Equal to engine speed: Lock-up on (after warming up engine)
·
Nearly equal to engine speed: Lock-up off (idling with shift lever in N) |
Data is displayed in increments of 50 rpm |
| NT Sensor Voltage | NT sensor voltage | Min.: 0.000 V Max.: 4.999 V |
0.1 to 1.9 V: Idling | - |
| Tester Display |
|---|
| NT Sensor Speed |
| NT Sensor Voltage |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
Disconnect the transmission wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C33)Location & Routingewd_type=routing;type=c;code=C33 |
||
| C33-22 (NTO) - Body ground | Always | 99 to 101 Ω |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C33)Location & Routingewd_type=routing;type=c;code=C33 |
||
| C33-21 (NTB) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector (to Transmission Revolution Sensor (NT)) |
| *b | Component without harness connected (Transmission Wire) |
Disconnect the transmission revolution sensor (NT) connector.
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SPEED SENSOR>REMOVAL
Disconnect the transmission wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C33)Location & Routingewd_type=routing;type=c;code=C33 |
||
| Terminal 2 of the transmission revolution sensor (NT) connector - C33-21 (NTB) | Always | Below 1 Ω |
| Terminal 1 of the transmission revolution sensor (NT) connector - C33-22 (NTO) | Always | Below 1 Ω |
| Terminal 2 of the transmission revolution sensor (NT) connector or C33-21 (NTB) - Body ground | Always | 10 kΩ or higher |
| Terminal 1 of the transmission revolution sensor (NT) connector or C33-22 (NTO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the transmission wire connector.
Disconnect the TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C33,C36)Location & Routingewd_type=routing;type=c,c;code=C33,C36 |
||
| C33-21 (NTB) - C36-30 (NTB) | Always | Below 1 Ω |
| C33-22 (NTO) - C36-11 (NTO) | Always | Below 1 Ω |
| C33-21 (NTB) or C36-30 (NTB) - Body ground | Always | 10 kΩ or higher |
| C33-22 (NTO) or C36-11 (NTO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
NEXT