Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for V35A-FTS)
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0472752 AUTOMATIC TRANSMISSION SYSTEM(for V35A-FTS) C

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for V35A-FTS)  P070513  Transmission Range Sensor "A" Circuit Open  P070562  Transmission Range Sensor "A" Signal Compare Failure  


DESCRIPTION

The park/neutral position switch assembly detect the shift lever position and send signals to the TCM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P070513 Transmission Range Sensor "A" Circuit Open P, R, N and D input signals are all OFF simultaneously for 60 seconds or more (2-trip detection logic).
·

Wire harness or connector

·

Park/neutral position switch assembly

·

TCM


Comes on DTC stored SAE: P0705
P070562 Transmission Range Sensor "A" Signal Compare Failure 2 or more of the following signals are ON simultaneously for 2 seconds or more (2-trip detection logic):
·

P or N input signal

·

R input signal

·

D input signal


·

Wire harness or connector

·

Park/neutral position switch assembly

·

TCM


Comes on DTC stored SAE: P0705

DTC Detection Condition Patterns (P070562):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5
Diagnostic Condition Ignition switch is ON ○ ○ ○ ○ ○
Malfunction Condition P input signal is ON ○ ○ - - -
R input signal is ON ○ - ○ - ○
N input signal is ON - - ○ ○ -
D input signal is ON - ○ - ○ ○
Duration 2 seconds or more 2 seconds or more 2 seconds or more 2 seconds or more 2 seconds or more
Detection Logic 2-trip detection logic 2-trip detection logic 2-trip detection logic 2-trip detection logic 2-trip detection logic

HINT:

DTC P070562 is stored when any of the above detection patterns is met.


MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch assembly or the wire harness in the park/neutral position switch circuit.

The park/neutral position switch assembly detects the shift lever position and sends a signal to the TCM. For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch assembly sends a signal to the TCM according to the shift lever position (P, R, N or D).

The TCM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The TCM will then illuminate the MIL and store a DTC.

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

Wait with the shift lever in each position (P, R, N or D) for 60 seconds or more with the ignition switch ON.

4.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

5.

Input the DTC: P070513 or P070562.

6.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C458218E02
5.125,0.49 5.438,0.688 0.313,0.198 10 false 15 5.125,1.094 5.438,1.292 0.313,0.198 10 false 34 5.115,1.688 5.427,1.885 0.313,0.198 10 false 16 5.115,2.281 5.427,2.479 0.313,0.198 10 false 35 5.458,0.5 5.615,0.698 0.156,0.198 10 false P 5.448,1.688 5.604,1.885 0.156,0.198 10 false N 5.458,1.094 5.615,1.292 0.156,0.198 10 false R 5.448,2.292 5.604,2.49 0.156,0.198 10 false D 3.313,0.49 3.625,0.688 0.313,0.198 10 false PL 3.313,1.094 3.625,1.292 0.313,0.198 10 false RL 3.313,1.688 3.625,1.885 0.313,0.198 10 false NL 3.313,2.281 3.625,2.479 0.313,0.198 10 false DL 2.615,1.396 2.927,1.594 0.313,0.198 10 false RB 2.385,2.906 2.844,3.104 0.458,0.198 10 false C34 2.385,3.083 3.76,3.469 1.375,0.385 10 false Park/Neutral Position Switch Assembly 5.813,3.198 6.271,3.396 0.458,0.198 10 false C36 5.823,3.375 6.625,3.688 0.802,0.313 10 false TCM 3.615,0.49 3.771,0.688 0.156,0.198 10 false 6 3.625,1.094 3.781,1.292 0.156,0.198 10 false 1 3.615,1.688 3.771,1.885 0.156,0.198 10 false 9 3.615,2.281 3.771,2.479 0.156,0.198 10 false 7 2.365,1.396 2.521,1.594 0.156,0.198 10 false 2 0.396,1.521 2.385,1.719 1.99,0.198 10 false from BKUP LP Fuse

CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for V35A-FTS)>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.READ VALUE USING GTS (SHIFT SW STATUS)
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (P Range) Park/neutral position switch assembly status OFF or ON
·

OFF: Shift lever not in P

·

ON: Shift lever in P


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Shift SW Status (R Range) Park/neutral position switch assembly status OFF or ON
·

OFF: Shift lever not in R

·

ON: Shift lever in R


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Shift SW Status (N Range) Park/neutral position switch assembly status OFF or ON
·

OFF: Shift lever not in N

·

ON: Shift lever in N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Shift SW Status (D Range) Park/neutral position switch assembly status OFF or ON
·

OFF: Shift lever not in D, M, "+" or "-"

·

ON: Shift lever in D, M, "+" or "-"


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (D Range)
50003 373 15,14,13,28

Result:
Result Proceed to
Data List values are normal A
Data List values are not normal B



A

B

2.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
2.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C34)Location & Routing

Click Connector(C34)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Park/Neutral Position Switch Assembly

C34-2 (RB) - Body ground Ignition switch ON 11 to 14 V
C34-2 (RB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C193931C69
0.115,1.094 0.573,1.365 0.458,0.271 2.167,0.25 1.833,0.25 1.833,0.25 1.625,0.938 true 2.583,0.5 2.333,0.5 2.333,0.5 2.042,1 true 2.167,2 1.917,2 1.917,2 1.792,1.479 true 0.833,1.833 1.083,1.833 1.083,1.833 1.24,1.469 true 2.688,1.833 2.438,1.833 2.438,1.833 2.135,1.49 true 2.219,0.156 2.583,0.396 0.365,0.24 10 false RB 2.635,0.406 2.958,0.604 0.323,0.198 10 false RL 0.635,1.75 1.104,1.938 0.469,0.188 10 false NL 2.219,1.927 2.74,2.094 0.521,0.167 10 false DL 0.104,0.073 0.281,0.271 0.177,0.198 10 false *a 2.729,1.75 3.25,1.917 0.521,0.167 10 false PL 0.24,1.167 0.698,1.365 0.458,0.198 10 false C34
*a Component without harness connected
(Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C34)Location & Routing

Click Connector(C34)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Park/Neutral Position Switch Assembly

C34-2 (RB) - C34-6 (PL) Shift lever in P Below 1 Ω
Shift lever not in P 10 kΩ or higher
C34-2 (RB) - C34-1 (RL) Shift lever in R Below 1 Ω
Shift lever not in R 10 kΩ or higher
C34-2 (RB) - C34-9 (NL) Shift lever in N Below 1 Ω
Shift lever not in N 10 kΩ or higher
C34-2 (RB) - C34-7 (DL) Shift lever in D, M, "+" or "-" Below 1 Ω
Shift lever not in D, M, "+" or "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - TCM)

NG

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - TCM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C34,C36)Location & Routing

Click Connector(C34)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Park/Neutral Position Switch Assembly

Click Connector(C36)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Transmission Control ECU Assembly

C34-6 (PL) - C36-15 (P) Always Below 1 Ω
C34-1 (RL) - C36-34 (R) Always Below 1 Ω
C34-9 (NL) - C36-16 (N) Always Below 1 Ω
C34-7 (DL) - C36-35 (D) Always Below 1 Ω
C34-6 (PL) or C36-15 (P) - Body ground and other terminals Always 10 kΩ or higher
C34-1 (RL) or C36-34 (R) - Body ground and other terminals Always 10 kΩ or higher
C34-9 (NL) or C36-16 (N) - Body ground and other terminals Always 10 kΩ or higher
C34-7 (DL) or C36-35 (D) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR